98-422-0 LightSpectrumSensor LSS

LightSpectrumSensor LSS
Item no.: 98-422-0
For project use – on request only
Digital light sensor with multiple colour sensor for measuring complete visible light spectrum plus UVA
sensor element. Two section housing with interface and sensor box. Connection to standard ethernet
10/100 Mbit power over Ethernet (PoE) Interface. Functionality only in combination with Eutrac NetComposer and project software on a monitoring PC (not included).
Technical Manual:
The LightSpectrumSensor offers precise light controlling in combination with the NetComposer and
project software for light sensitive areas. With the optional project software the measured values can be
saved in a database. Finally a detailed specification has to be appointed for every project.
Hardware:
Sensor head can be mounted up to 1 m (3.28 ft) from the interface box
Sensor specification:
-
LUX level: 7-1000 LUX, resolution 7 LUX, +/- 10%
RGB light levels for calculation of light colour, tolerance +/- 15%
UVA light 310-370 nm, min. sensitivity 2 µW/cm², resolution 0,5 µW/cm², tolerance +/- 15%
Temperature -40°C (-40°F) to +123°C (253.4°F), resolution 0,01°C, typical tolerance +/- 1,0°C
Humidity sensor 0-100% RH, resolution 0,05%, typical tolerance +/- 5% (20-80% RH)
Interface box: Standard ethernet network 10/100 Mbit with Power over Ethernet (PoE)
Software:
-
All light data (LUX, R, G, B, UV) can be saved in project data base
Actual LightColour is calculated and shown on monitoring page
Precise constant light controlling with adjustable delay time via Ne tComposer
Analysis of data base depends on project case (specified with customer)
Measurement interval: 3 s
Important note: The Sensor is not conforming to standard luxmeters because it has a higher angle addiction. Comparison can be done on site. Calibration for lamp type necessary on site, each sensor can
be calibrated to one lamp type only!
Colour sensor is not usable for mixed light or areas with daylight incidence!
Technical changes reserved – 06.2012 – EUTRAC GmbH
Wiring diagram:
+24VDC
-24VDC
TCP/IP LAN
TCP/IP
LightSpectrum
Sensor LSS
FE
NC
C
NO
Sensor
Ethernet
10/100
CONTROL OUT
max. 1m
NetComposer NCR
DMX A
24V DC
+
-
A+
B- GND
DMX B
A+
B- GND
DALI A
DALI B
D+ D-
D+ D-
DALI line with
a max.bis
of max.
64 participating
devices
DALI-Linie
64 Teilnehmer
max. 300 1,5 mm²
DA
DA
DALIBallast
L N PE
DA
DA
DALIBallast
L N PE
DA
DA
DALIBallast
L N PE
DMX Line DMX-Linie
accordinggem.
to DMX
standard with
a max.
of 512 addresses
DMX-Richtlinie
bis 512
Adressen
+
G
DMXBallast
L N PE
+
G
+
G
DMXBallast
L N PE
+
G
+
G
DMXBallast
+
G
L N PE
L
N
PE
Mounting and installation instructions:
•
•
•
Mounting the sensor head on walls
Mounting interface box hidden in walls
maximum distance from the interface box 1m (Extansion on request)
Technical Data:
Dimensions:
Weight:
Permissible ambient
temperature:
Inputs:
Mounting:
Outputs:
Input voltage:
Housing material:
Protection:
EMC according to:
80x80x25 mm Interface-Box
80x15x8 mm Sensor head
ca. 120 g Interface-Box
ca. 30 g Sensor head
0 … +50°C
Standart Ethernet 10/100 Mbit
wall Mount
light intensity, RGB light colour,
UV-intensity, temperature, humidity
PoE via Ethernet
Metal black coating (I-Box),
Plastic (sensor)
IP20
EN55015, EN 61000-3-2
For more information about NetComposer System have a look to:
www.intelligentlighting.de
Datenblätter in Deutsch und weitere Informationen finden Sie auf:
www.intelligentlighting.de
Technical changes reserved – 06.2012 – EUTRAC GmbH