Fiche technique
Transcription
Fiche technique
Fiche technique SX Contractors SX Contractors Gun Grade PU Expanding Foam Gun grade PU expanding foam. Spécifications techniques Temperature d'application From +5°C to +35°C Type Polyurethane Structure 70% Temp de durcissement 50-150 mins Durcissement à coeur 50-100 mins Densité 18-25 kg/m3 Poids spécifique FEICA TM1004 -5% < DS < 0% Classe d'inflammabilité B3 Description du produit Capacité d'isolation phonique 58dB An easy to use, polyurethane based expanding foam for professional use in general construction and home improvement applications. Must only be used with a gun grade applicator - SX PU Foam Applicator Gun is recommended. Sec au toucher FEICA TM1014 From -40°C +90°C Résistance à la température Conductivité thermique m.K 30-35 W / Yield FEICA TM1003 750ml = 35-40 litres Avantages • - Expands up to 30 times it's original volume. • - Quick drying. 8-15 mins Restrictions Applications Filling large, irregular or awkward gaps where the foam will expand to completely fill the cavity. Fixing window and door frames, loose tiles and boards. Insulating between brickwork and cladding, around ductwork and through cavities carrying pipes and cables. Backing in low expansion joints can be used as a backing material in all types of sealant applications. • Not recommended for use on silicone, PTFE, PE, PP or greasy and oily surfaces • Not suitable for continuous water immersion or use in enclosed spaces • When exposed to sunlight apply sealant or render within 7 days as the foam is not resistant to UV light • The foam does provide a barrier to moisture, but allows water vapour to migrate through the foam Préparation des surfaces et finition Ensure surfaces to be treated are free from grease, dust and loose material. It is important to moisten surfaces well before use as this improves adhesion and finished cell structure of the foam. Can be cut, sanded, plastered or painted when fully cured. The foam should be painted or coated within 7 days if it is exposed to sunlight as it is not resistant to ultra violet light. Afterwards, normally the foam applicator gun should be left attached to a can of foam to ensure the entire system is closed. To reuse, simply break off the nib of foam at the end of the Den Braven France sarl. Z.I. Le Meux - Rue du buisson du roi - BP 20114 – FR 60881 LE MEUX CEDEX T +33 (0)3 44 91 68 68 | F +33 (0)3 44 91 68 92 | E [email protected] 2016-09-29 21:00:08 UTC Fiche technique SX Contractors SX Contractors Gun Grade PU Expanding Foam Gun grade PU expanding foam. gun applicator nozzle, shake can well and start application. Before replacing cans, close the gun valve and unscrew empty can. Immediately replace with a full can or clean the foam applicator gun thoroughly with SX PU Foam Cleaner. It is the user's responsibility to dispose of all packaging correctly. Mise en peinture Can be painted when fully cured. Nettoyage Clean the foam applicator gun thoroughly with SX PU Foam Cleaner. Couleur(s) standard(s) • Green Conditionnement • 700ml canister (packed 1 x 12). 1 pallet = 960 canisters Stockage et conservation Shelflife of 12 months after production date. Store upright with valve up in unopened original packaging betw Sécurité Avant l’utilisation du produit, la Fiche de Données de Sécurité (FDS) doit être lue et comprise. FDS disponible sur demande pour les utilisateurs professionnels et sur notre site internet. Garantie Den Braven garantit que son produit est conforme à sa spécification durant sa durée de conversation. Disclaimer Les informations dans ce document et aussi dans nos publications imprimées et digitales sont fondées sur nos connaissances et expériences actuelles. Den Braven n’est pas responsable des fautes, inexactitudes ou déficiences rédactionnelles qui sont le résultat de changements ou recherches technologiques entre la date de publication de ce document et la date de l’acquisition du produit. Den Braven se réserve le droit de changer des formulations. Avant d’appliquer le produit l’utilisateur doit se familiariser avec les informations présentées dans ce document et/ou dans tout autre document y afférent. Avant l’application du produit l’utilisateur doit effectuer les tests nécessaires pour assurer que le produit est adapté à l’application. La méthode d’application, les conditions lors du stockage et du transport échappent à notre contrôle et seront en conséquence pas de notre responsabilité. Une responsabilité pour cette fiche d’information produit ne peut pas être acceptée. Les livraisons se font uniquement à nos conditions de livraison et modalités de paiement. Les informations détaillées de la présente fiche technique sont données à titre indicatif et ne sont pas exhaustives. Den Braven France sarl. Z.I. Le Meux - Rue du buisson du roi - BP 20114 – FR 60881 LE MEUX CEDEX T +33 (0)3 44 91 68 68 | F +33 (0)3 44 91 68 92 | E [email protected] 2016-09-29 21:00:08 UTC