Booster Adapter Adap-Roco
Transcription
Booster Adapter Adap-Roco
Littfinski DatenTechnik (LDT) Operating Instruction Instructionedienungsa Booster Adapter Adap-Roco A maximum of four Roco-Booster respectively three RocoBooster and one Booster Adapter Adap-Roco can be operated on each Roco-Command Station 10761 or 10764. Up to ten DigitalBooster DB-2 can be connected to each Booster-Adapter Adap-Roco. If you need more digital current on your layout you can use a second booster adapter AdapRoco for further ten DigitalBooster DB-2. For this assembly is it possible to use one case LDT-01 for two booster adapter Adap-Roco. from the Digital-Professional-Series! Adap-Roco-G Part-No.: 088403 >> finished module in a case << By using the Booster-Adapter Adap-Roco you can implement our low-cost DigitalBooster DB-2 on a Roco-command station 10761 or 10764. With each Adapter Adap-Roco is it possible to connect up to ten DigitalBooster DB-2 on a Rococommand station! This product is not a toy! Not suitable for children under 14 years of age! The kit contains small parts, which should be kept away from children under 3! Improper use will imply danger or injuring due to sharp edges and tips! Please store this instruction carefully. Introduction/Safety Instruction: Connecting the DigitalBooster DB-2: You have purchased the Booster Adapter Adap-Roco that is supplied within the assortment of Littfinski DatenTechnik (LDT). Insert the 5-poles plug-connector of the booster bus cable that way onto the pin bar plug ST1 of the booster adapter Adap-Roco that the white single wire of the booster bus cable corresponds to the white marking next to the pin bar. The plug shall never be inserted offset to the pin bar. We wish you having a good time using this product. • Please read the following instructions carefully. Warranty will expire due to damages caused by disregarding the operating instructions. LDT will also be not liable for any consequential damages caused by improper use or installation. The finished module in a case comes with 24 month warranty. Connecting the adapter to the RocoCommand Station or to the Roco-Booster: • Attention: Please switch off your digital control unit and unplug all transformers from AC-current before starting to assemble the unit. The booster adapter Adap-Roco will be supplied together with a cable for the connection of the Booster Adapter to the Roco-Command Station 10761 or 10764. Insert one of the two connection cable plugs into the socket “IN” of the booster adapter “Adap-Roco” and the second plug into the socket “Booster Out” of the Roco-Command Station 10761 or 10764. If you already use one or more Roco-Booster 10762 or 10765 please connect the Booster Adapter Adap-Roco with the socket “Booster Out” of the last Roco-Booster. Adapter to the Connect the DigitalBooster DB-2 to the transformer and the rail in accordance to the operation manual of the DB-2. The rail sections which are supported by the RocoCommand Station or by a Roco-Booster and a DigitalBooster DB-2 have to be electrical separated on both sides. If it comes to a short circuit during a train is passing the rail splitting (Lokmaus or multiMAUS indicates “short circuit“) you should change the two digital wires “red” and “brown” (clamp KL2) at the DigitalBooster DB-2. Two track sections which are supported by two different DigitalBooster DB-2 have to be separated on one side only which will be supported by the digital wire “red“. The galvanic separation between DigitalBooster DB-2 and Command Station 10761/10764 will be provided by optical coupling devices on the booster adapter Adap-Roco and assures therefore a safe electrical operation. As soon as the booster adapter Adap-Roco will get current supply from the switched-on DigitalBooster DB-2 the red light emitting diode of the adapter lightens up and indicates that the adapter is ready to operate. Colored sample connections can found within our Web-Site www.ldt-infocenter.com at he area “Downloads”. Littfinski DatenTechnik (LDT) OUT Rev. 1.1 LED1 ST1 Adap-Roco Digital-Profi werden! Adap-Roco Boosteradapter für den Betrieb von bis zu 10 Digitalbooster DB-2 pro Adapter an einer Roco Digitalzentrale (z.B. 10761 /10764). Littfinski DatenTechnik (LDT) D-25492 Heist Multi-Digital www.ldt-infocenter.com BU1 BU2 IN OUT Connecting the first DigitalBooster DB2 via the Booster-Adapter Adap-Roco with the Fleischmann Command Station 680801 Ç Ç braun brown rot red FLEISCHMANN multiMAUS STOP OK 2abc def 3 5jkl mno 6 8 tuv wxyz9 0 MENU weiss white KK1 OUT 7 pqrs Littfinski DatenTechnik (LDT) 1 4 ghi DB-2 Rev. 2.4 Rev. 1.1 ST1 Adap-Roco 680801 LED1 FLEISCHMANN MF1 Digital-Profi werden! Digital-Profi werden! Adap-Roco DigitalBooster-2 Boosteradapter DB-2 für den Betrieb von bis zu 10 Digitalbooster DB-2 pro Adapter an einer Roco Digitalzentrale (z.B. 10761 /10764). Littfinski DatenTechnik (LDT) D-25492 Heist Multi-Digital 2,5 Ampere Booster für die Digitalformate Marklin-Motorola, mfx®, M4 und DCC. Multi-Digital www.ldt-infocenter.com Power Track Booster in out out Slave BU1 Master IN Nur für trockene Räume, Keep dry www.ldt-infocenter.com KL2 BU2 OUT Littfinski DatenTechnik (LDT) D-25492 Heist + LED1 red brown K J ST1 OUT Littfinski DatenTechnik (LDT) weiss white Vom Modellbahntrafo From transformer KL1 ST2 IN brown yellow 16...18V~ braun gelb brown yellow Vom Modellbahntrafo From transformer Made in Europe by Littfinski DatenTechnik (LDT) Kleiner Ring 9 D-25492 Heist/Germany Phone: 0049 4122 / 977 381 Fax: 0049 4122 / 977 382 Internet: http://www.ldt-infocenter.com Subject to technical changes and errors. 03/2015 by LDT