BlueControl Flyer, PDF, english

HANTZ
+ PARTNER
The Upgrade Company! www.hantz.com
HANTZ
+ PARTNER
The Upgrade Company! www.hantz.com
BlueControl CL-I
BlueControl CL-I
Signal Description
Electrical Characteristics
No.
1
2
3
4
Name
NC
NC
RESET
MISO
Type
5
CSB
IN
IN
OUT
6
CLK
IN
7
MOSI
IN
8
9
10
11
12
CTS
TXD
RTS
RXD
USBD-
IN
OUT
OUT
IN
I/O
13
USBD+
I/O
14
15
GND
VCC3
Power
Power
16
17
18
19
20
21
22
23
24
25
26
27
28
PCMOUT
PCMSYNC
PCMIN
PCMCLK
SDA/PIO7
SCL/PIO6
DTR/PIO5
DCD/PIO4
DSR/PIO3
RI/PIO2
NC
NC
VCC
OUT
I/O
IN
I/O
I/O
I/O
I/O
I/O
I/O
I/O
A
A
Analogue
Power
Description
Not connected
Not connected
Reset input, active high
SPI data out
Only used for firmware download and configuration with
development kit. Leave unconnected for normal operation.
SPI chip select
Only used for firmware download and configuration with
development kit. Leave unconnected for normal operation.
SPI clock
Only used for firmware download and configuration with
development kit. Leave unconnected or connect to GND for
normal operation.
SPI data in.
Only used for firmware download and configuration with
development kit. Leave unconnected or connect to GND for
normal operation.
UART CTS
UART transmit data
UART RTS
UART receive data
USB D+ (note 1)
Connect to GND if not used
USB D- (note 1)
Connect to GND if not used
System ground
Regulated 3.3 Volt power input or output.
Connect to VCC if used as input.
PCM data out (note 2)
PCM sync (note 2)
PCM data in (note 2)
PCM clock (note 2)
I2C Data or general purpose I/O
I2C clock output or general purpose I/O
UART DTR output or general purpose I/O
UART DCD input / output or general purpose I/O
UART DSR input or general purpose I/O
UART RI input / output or general purpose I/O
Not connected
Not connected
Unregulated power supply. Connect to VCC3 if a regulated 3.3 V
power supply is used.
external antenna connector 50 Ohm
Connector type MMCX
Notes:
1
USB operation is subject to firmware support.
2
Codec operation is subject to firmware support.
2
1
NC
2
NC
3
RESET
VCC
28
NC
27
NC
4
MISO
26
RI/PIO2
5
25
CSB
DSR/PIO3
24
6
CLK
DCD/PIO4
23
7
MOSI
DTR/PIO5
22
8
CTS
SCL/PIO6
21
9
TXD
SDA/PIO7
20
10
RTS
PCMCLK
19
11
RXD
PCMIN
18
12
USBD-
PCMSYNC
17
13
USBD+
PCMOUT
16
14
GND
VCC3
15
A
Device Pin Out
Mechanical Dimensions
Absolute maximum ratings
Stresses above those listed here can cause permanent damage to the device.
Supply Voltage (VCC)
Supply Voltage (VCC3)
Storage temperature
20 V
3.6 V
-40 ... +85 °C
Recommended Operation Conditions
Item
Min
Operating Voltage VCC
4
Operating Voltage VCC3
3.2
Operation Temperature
-40
DC Electrical Characteristics
Item
Digital Terminals (except USB)
VIL Input Low Voltage
VIH Input High Voltage
VOL Output Low Voltage (IO=4mA)
VOH Output High Voltage (IO=-4mA)
USB Terminals
VIL Input Low Voltage
VIH Input High Voltage
VOL Output Low Voltage (IO=4mA)
VOH Output High Voltage (IO=-4mA)
Power Consumption
Operation Current Tx active at
maximum power
Device Idle
Notes:
1) VCC3 is 3.3 Volt typical when internal
Radio Characteristics
Item
Carrier Frequency
RF Antenna Impedance
RF Output Power
RF Receiver Sensitivity
Min
Typ.
3.3
Max
10
3.4
+70
Unit
V
V
°C
Notes
Typ.
Max
Unit
Notes
-0.4
0.7VCC3
0.8
V
VCC3+0.4 V
0.2
V
V
VCC3-0.2
0.3VCC3
0.7VCC3
0
2.8
110
0.2
VCC3
V
V
V
V
150
mA
tbd
1
1
1
1
mA
voltage regulator is used.
Min
2402
11
Typ.
50
14
-80
Max
2480
17
-70
Unit
MHz
Ohm
dBm
dBm
Notes
0.1% BER
Application Information
Serial Port
The BlueControl serial port supports all Bluetooth defined standard baud rates between
2400 bps and 230400 bps. By default RTS/CTS hardware handshake is used.
Antenna
When the internal antenna options is used make sure not to place any copper traces or
ground plane underneath the antenna because this can severely degrade the RF
performance of the device.
No traces within this area
3
BLUETOOTH is a trademark by the Bluetooth SIG Inc. Windows is a registered trademark of Microsoft.
BLUETOOTH is a trademark by the Bluetooth SIG Inc. Windows is a registered trademark of Microsoft.
HANTZ
+ PARTNER
The Upgrade Company! www.hantz.com
c
Class I + II Products
BlueControl CL-I
Bluetooth Class 1 Module
The Transparent Cable Replacement
BlueControl EVA-Board
The BlueControl CLI module is the perfect solution for your
with BlueControl CL-1
wireless control and measurement application. It integrates a
complete Bluetooth wireless solution in an easy to use dual in line
package. An RS232 type serial port, digital I/Os, an optional I2C master i n t e r f a c e
and a PCM codec interface for voice applications are available.
In normal operation mode one RFCOMM channel is used to transfer data to / from the serial
port. This is transparent to the application. A second RFCOMM channel can be used to control
the digital I/Os and / or I2C operation. Future firmware releases may also support other
protocols (like the HID protocol).
To configure the module for a specific application a developers kit is available. It comes with
an easy to use software for configuration and evaluation of the BlueControl module. The
developers kit is also compatible with industry standard software for advanced applications.
FEATURES
! Embedded Bluetooth 7 Protocol
Stack
! Host or Client roles supported
! External Stub Antenna
(Allows mounting in metal case)
! Range up to 30m with Bluetooth7
Some examples of possible applications follow:
! Range up to 100m with
Bluetooth7 Class 1
!
!
!
! Bluetooth 1.1 compliant
!
!
!
SERIAL INTERFACE
! Supported Baudrate 300-921Kbps
!
!
!
Commercial Systems, POS, Barcodescanner, printers, POS, CreditCard terminals
Sensors and measurement devices, building technology
Computer peripherals (Modem, ISDN, DSL, serial printer, Plotter, mobile phones +
PDA)
Industrial control, robotics, access control, parking lot control, signal controls
Medical technology, analyses (Glukometer, Breathcontrol aso.)
Military technology, save, non disturbish data/voice, target control systems,
Telemetrics
Embedded Systems, Mainboards, lock systems, Navigation systems
Technical Service, system configuration (ex. phone/PBX systems, Diagnostic
systems)
Automotive, car diagnostics, CAN-Bus control
PROTOCOLS
! L2CAP
! SDP
! RFCOMM
BLUETOOTH7 PROFILE
d
Key Features
!
Complete wireless solution including all Bluetooth protocol software components.
!
Bluetooth Class 1, up to 100 meter range.
!
Bluetooth Serial Port Profile
transparent operation, no software modifications or programming needed
! Generic Access Profile (GAP)
I
HANTZ + PARTNER GMBH
Gewerbestrasse 37
D-79194 Gundelfingen i.Br.
Phone +49-(0)761-592100
Telefax +49-(0)761-585228
E-Mail [email protected]
Internet www.hantz.de
Deutschland:
Schweiz:
HANTZ
+
PARTNER
Tel.: 0761 / 59 21 00
Tel.: 061 / 27 311 - 31
Fax: [email protected]
/ 58 52 28
Fax: 061 / 27 311 - 39
Support-Hotline
+49-5606-561111
The Upgrade Company!
www.hantz.com
*
! Service Discovery Profile (SDP)
!
RS232 interface with 3.3 V level
! Serial Port Profile (SPP)
!
Up to 6 digital I/Os
! LAN Access
!
Optional I2C master interface
! Dial Up Networking
!
PCM codec interface
!
Internal or external antenna
!
Regulated (3.3 Volt) or unregulated (4..10 Volt) power supply.
!
Can supply regulated 3.3 Volt to external devices.
!
DIL 28 standard package
! Fax
Österreich:
Tel.: 01 / 58 55 430
Fax: 01 / 58 55 460
July 2004 -T All Specifications are subject to change without notice
Class 2
Support-Hotline
+49-5606-561111 * [email protected]
Suppor
*
BLUETOOTH is a trademark by the Bluetooth SIG Inc. Windows is a registered trademark of Microsoft.