Install on XboX 360 SLIM (1/4)
Transcription
Install on XboX 360 SLIM (1/4)
How to install it http://www.x360glitchip.com/ Install on XboX 360 SLIM (1/4) There are 2 Trinity revision of the motherboard (Slim), but both are compatible with the Reset Hack Glitch. The installation is the same for both type of motherboard. WARNING : If your modchip is NOT PROGRAMMED YET, please refer to the manual « Flash of x360Glitchip » Use scotch to place the chip on the motherboard. Take care that the space is enough between JTAG Pins and your DVD Drive in order to avoid any electric hazards. If it’s not, please cut or short the pins AFTER having flashed it. Take care that short FAT1 and FAT2 are NOT made. Then start to short SLIM1 and SLIM2 on the x360 Glitchip in order to active the Slim mode on the modchip. Wire Points We advise you to make double your wire for 3.3v and GND. Indeed, the chip needs a good and stable voltage and Ground. Moreover, if you get bad result with the Ground on J2C3.12, take it directly on the video port. Wire Points are : J2C3.7 3.3v J2C3.12 GND C3B10 B J2C3.10 D J2C3.9 E This wires are under the motherboard : FT5R2 A FT4R2 F Install on XboX 360 SLIM (2/4) There are 2 Trinity revision of the motherboard (Slim), but both are compatible with the Reset Hack Glitch. The installation is the same for both type of motherboard. Begin to identify the area where to process on your Slim motherboard. There are 7 wires on Slims, 5 on the top of the motherboard, and 2 on the back. J2C3.7 3.3v J2C3.12 GND J2C3.9 E J2C3.10 D C3B10 B Double Wires on 3.3v and GND Install on XboX 360 SLIM (3/4) FT5R2 A FT4R2 F Install on XboX 360 SLIM (4/4) Here a complete installation with the recommended position for the chip Install on XboX 360 FAT (1/5) All Xbox 360 FAT are compatible with the Reset Glitch Hack (Except Xenon). Installation is same for all compatible revisions (Zephyr, Falcon, Jasper, JasperBB) WARNING : If your modchip is NOT PROGRAMMED YET, please refer to the manual « Flash of x360Glitchip » Use scotch to place the chip on the motherboard. Take care that short SLIM1 and SLIM2 are NOT made. Then start to short FAT1 and FAT2 on the x360 Glitchip in order to active the FAT mode on the modchip. Wires Points We advise you to make double your wire for 3.3v and GND. Indeed, the chip needs a good and stable voltage and Ground. Wire Points are : J2B1.7 3.3v J2B1.12 GND C3B2 B J8C1.2 F These wires are under the motherboard : FT6U7 A Under R7R17 C Install on XboX 360 FAT (2/5) All Xbox 360 FAT are compatible with the Reset Glitch Hack (Except Xenon). Installation is same for all compatible revisions (Zephyr, Falcon, Jasper, JasperBB) Begin to identify the area where to process on your FAT motherboard. There are 6 wires on FAT, 4 on the top of the motherboard, and 2 on the back. J2B1.7 3.3v J2B1.12 GND J8C1.2 F C3B2 B Install on XboX 360 FAT (3/5) Under R7R17 C FT6U7 A Install on XboX 360 FAT (4/5) Here a complete installation with the recommended position for the chip Install on XboX 360 FAT (5/5)