kandi stix ho
Transcription
kandi stix ho
KANDI STIX HO I N S T A L L A T I O N Verify electrical plan. KANDIscrew STIX holes. Rotate fixture to expose Make sure to use allEnd fourCap screw holes when mounting. 1 2 Ensure Power is Off! Junction Max Box Run Lengths: 110pc at 120v, 300pc at 277v 10’ KANDI STIX Leader Cable Not Included 3 Optional: 0-10v wiring diagram Optional Dimming With ON/OFF Control Wiring Diagram Using Lutron NTFTV & PP-20 (By others): Connect the NTFTV dimmer as shown below. Use only Lutron PP-20 Power Packs for AC line switching. Do not install the PP-20 in the same wallbox as the Low - Voltage Ballast Control. Refer to the wiring sheet included with the PP-20 for more information Max run 55 fixtures at 120v, 150 fixtures at 277v #55 #54 Optional 1’ Jumper Cable End Cap 0-10v Dimmer only Lutron Model: NTFTV Purple Gray 100-277v If dimming AC wire to: 50/60Hz Lutron PP-20 White #1 Black Black White Purple Gray 10’ KANDI STIX Leader Cable THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS. All MODA LIGHT products should be installed by a Licensed Electrician to local & national code. Do not modify, adapt or cut any MODA LIGHT components, plugs or accessories. Any modifications will void the warranty and may create a potential safety hazard. Do not put on the same circuit as inductive loads. Incorrect wiring will result in irreparable permanent damage to the LEDs and fixture. MODA LIGHT tests all products before shipping, and will not replace items that have been destroyed by incorrect wiring or handling. Ensure electrical circuit is switched off before wiring. See MODA LIGHT terms and conditions for product limited warranty. © Cop yrig ht 2 01 5 • 955 W hit e Dr iv e, Las Vega s , N V 8 9 11 9 • T: 7 0 2 4 0 7 7 7 7 5 • F : 7 0 2 4 0 7 7 7 7 3 • w w w.m o d a l i g h t.co m KANDI STIX HO I N S T A L L A T I O N 4 KANDI STIX End Cap Optional 1’ KANDI STIX Jumper Cable 5 #1 100-277v AC 50/60Hz #2 ..... Max Run Lengths: 55pcs at 120v, 150pcs at 277v #54 #55 End Cap Must be Placed on Last Fixture THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS. All MODA LIGHT products should be installed by a Licensed Electrician to local & national code. Do not modify, adapt or cut any MODA LIGHT components, plugs or accessories. Any modifications will void the warranty and may create a potential safety hazard. Do not put on the same circuit as inductive loads. Incorrect wiring will result in irreparable permanent damage to the LEDs and fixture. MODA LIGHT tests all products before shipping, and will not replace items that have been destroyed by incorrect wiring or handling. Ensure electrical circuit is switched off before wiring. See MODA LIGHT terms and conditions for product limited warranty. © Cop yrig ht 2 01 5 • 955 W hit e Dr iv e, Las Vega s , N V 8 9 11 9 • T: 7 0 2 4 0 7 7 7 7 5 • F : 7 0 2 4 0 7 7 7 7 3 • w w w.m o d a l i g h t.co m