AR10 Snap-On Smart Card Reader Compliance Insert

AR10 Snap-On Smart Card Reader Compliance Insert
Model 1000AA11
Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future
reference.
Users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories
other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the
compliance of this product and may result in the loss of the user’s authority to operate the equipment.
Caution: When charging the combination of the 70 Series and AR10 through the I/O connector at the base of the AR10, use
Intermec Model 1002UU01, 1002UU02, or 1002UU04. Use of incorrect charger may present a risk of fire or explosion.
U.S.A. Digital Emissions Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at their own expense.
Canadian Digital Apparatus Compliance
This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
CAN ICES-3 (A)/NMB-3 (A)
Pour les utilisateurs canadiens (fr)
Mise en garde : Cette marque indique que l’utilisateur doit lire toute la documentation incluse avant l’utilisation. Conservez ce
supplément pour référence future.
Les utilisateurs de ce produit sont mis en garde contre l’utilisation d’accessoires et de périphériques qui ne sont pas approuvés par Intermec
Technologies Corporation. L’utilisation d’accessoires autres que ceux recommandés ou des changements à ce produit qui ne sont pas
approuvés par Intermec Technologies Corporation peuvent annuler la conformité de ce produit et mettre fin au droit qu’a l’usager d’utiliser
l’équipement.
Mise en garde : Lors de la mise en charge de la combinaison de la série 70 et de l’AR10 par le biais d’un connecteur I/O à la base de
‘AR10 , utiliser le bloc d’alimentation Intermec modèles 1002UU01, 1002UU02, ou 1002UU04. L’utilisation d’un autre chargeur
risque de présenter un risque d’incendie ou d’explosion.
Conformité aux normes sur les émissions numériques
Cet appareil est conforme aux normes RSS avec exemption de licence d’Industrie Canada. L’utilisation est assujettie aux deux conditions
suivantes : (1) Ce dispositif ne doit pas causer d’interférence dommageable et (2) Ce dispositif doit tolérer toute interférence, incluant
l’interférence pouvant causer un fonctionnement indésirable.
CAN ICES-3 (A)/NMB-3 (A)
1
by Honeywell
AR10 Snap-On Smart Card Reader Compliance Insert
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
*933-317-001*
© 2014 Intermec by Honeywell
All rights reserved.
P/N 933-317-001, Revision A