Matrix 424/832/832+
Transcription
Matrix 424/832/832+
Matrix 424/832/832+ Centrale d’alarme avec claviers et lecteurs de proximité Version Software 4 REMARQUES ACTUALISÉES Nouvelles fonctions Les nouvelles fonction suivantes ont été rajoutées à la version 4 CD Logiciel Le logiciel est maintenant actualisé pour coïncider avec les changements de la version 4. Système sans fil On peut maintenant raccorder jusqu’à 16 détecteurs sans fil (KX12DW ou UT3DW) à la Matrix 832+ par le nouveau MXRIX8DW (extension 8 zones sans fil). Jusqu’à 2 extensions sans fil peuvent être raccordées sur le bus. Télécommandes Le système Matrix peut maintenant être armé et désarmé par une télécommande (KF4DW). Autres actions également disponibles. Changements par rapport aux fonctions installateur existantes a: Trouver dispositifs sur le bus Matrix Comme le système sans fil a été rajouté, la fonction Scan pour dispositifs fonctionne et compte jusque 82. a#: En second lieu options du système, Option 3, Mode installateur pas possible quand armé Cette fonction a été supprimée. a: Quitter le menu installateur Quand le menu installateur a été quitté, et un sabotage a été reconnu, vous entendez une tonalité basse et le trouble sera affiché. Pour quitter le menu installateur, appuyez aet . Nouvelles options N° Fonc 201 Paramètres / Options en second lieu options système Réservé 3 202 OFF ON Réservé Réservé Ne cause pas sabotage Uniqu. pendant délai d’entrée [Cause alarme sabotage] [Toujours permis] [Non] Oui [Inactif] Actif [4] 8 [Suivant options transmission] Troisièmes options système 7 8 250 Trouble RF Jam quand armé Désarmement par télécommande Options zones globales 5 301 Zones fin de ligne simple EOL Attributs code d’utilisateur 6 610 Ré-armement forcé Deuxièmes options ligne tél. 3 Evénement recompose 4 Transmission MX485 RINS969-4 Envoyer tous Page 1 Matrix 424 832 832+ Release Notes French Nouvelles fonctions installateur a: Numéro version de la centrale Permet à l’installateur de vérifier le numéro version de la centrale, sans vérifier la puce principale de la centrale Matrix. a: Assigner des fonctions aux touches de la télécommande L’extension sans fil permet de programmer jusqu’à 32 télécommandes (KF4DW). Cette fonction permet à l’installateur de programmer les touches de fonction. Nouvelles sorties ortie N° 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Derscription des sorties Suivant alarme médicale Suivant trouble batterie suivant sous menace Suivant désarmé Suivant troubles système Suivant intrusion momentané Suivant momentané 24 HEURES Suivant momentané INCENDIE Suivant momentané MEDICAL Suivant momentané PA Suivant momentané SABOTAGE Suivant momentané SOUS MENACE Suivant momentané TROUBLE COM Suivant momentané TROUBLE RKP Suivant momentané APPEL TEST Sorties statut LED Télécommande contrôlée Nouveaux événements contact ID Groupe 4: MAINTENANCE 1 ou 3 344 Détection Jam Extension RF détecte trouble 01-04 000 1 ou 3 381 Perte supervision Détecteur arrête la supervision 01-04 016-032 1 ou 3 384 RF batterie faible Batterie faible dans un détecteur RF 01-04 016-032 Centrale d’alarme avec claviers et lecteurs de proximité Version Software 4+ New Options The following new options are now available: 610 Telephone Line Options 2 5 Event Duplication OFF ON No Yes Event Duplication: This function allows event signalling for partition 3 to follow partition 1, and partition 4 to follow partition 2. Partitions 3 and 4 cannot be used for any zones if this function is enabled; they are only used for signalling purposes. It then gives the option of signalling to extra telephone numbers for partitions 1 and 2. In the send options function, all partition 3 events need to be programmed the same as partition 1, and all partition 4 events need to be programmed the same as partition 2. An example of how this function works is shown below: Telephone Number Page 2 Back Up Tel No. Account Code ARC RINS969-4 Matrix 424 832 832+ Release Notes French Partition 1 Partition 3 Alarm Events 1 3 2 4 1111 1111 ARC 1 ARC 2 In the above scenario, if an alarm occurred on partition 1, it would dial to telephone number 1 with the account code 1111 to the first ARC. The events that partition 1 sent would then be duplicated to partition 3, which would dial telephone number 3 with the same account code, to the second ARC. Partition 2 would operate as follows: Partition 2 Partition 4 Alarm Events Telephone Number 1 3 Back Up Tel No. 2 4 Account Code 2222 2222 ARC ARC 1 ARC 2 In the above scenario, if an alarm occurred on partition 2, it would dial to telephone number 1 with the account code 2222 to the first ARC. The events that partition 2 sent would then be duplicated to partition 4, which would dial telephone number 3 with the same account code, to the second ARC. Engineer Reset If the below options are both turned ON; an Engineer Reset is only needed for any TAMPER ALARMS. A user code will be able to reset ALL OTHER ALARMS. FUNCTION 401 OPTION NUMBER 3 ON = ENGINEER RESET ENABLED OPTION NUMBER 4 ON = RESET REQUIRED AFTER ALL ALARMS temps de surveillance a: temps de surveillance Le temps de surveillance varie de 00 (off), à 99 (99 heures) et est utilisé pour vérifier la radio détecteurs / transmetteurs dans le système. OUTPUT NUMBER: 48 Centrale d’alarme avec claviers et lecteurs de proximité Version Software 5 64 Zones - Zone Doubling Using version 5 software it is possible to zone double up to 64 zones. Please see the installation manual. RINS969-4 Page 3