De la caractérisation micromécanique du vieillissemnt
Transcription
De la caractérisation micromécanique du vieillissemnt
Références bibliographiques ADAMSON M.J., Thermal expansion and swelling of cured epoxy resin used in graphite/epoxy composite materials, J. Mater. Sci., 1980, Vol. 15, pp. 1736-1745 AFNOR, Essais de délaminage en flexion, NFT57 – 104, Paris : AFNOR 1986 AHLSTROM C., GERARD J.F., The adhesion of elastomer coated glass fibers to an epoxy matrix. Part I: the effect of the surface treatments on the tensile strength of the glass fibers, Polym. Compos., 1995, Vol. 16, pp. 305-312 AHLSTROM C., Interface fibre de verre / matrice polyépoxy - Introduction d’une interphase à propriétés contrôlées, Thèse de Doctorat, Institut National des Sciences Appliquées, 1991, 295 p. AMDOUNI N., Caractérisation et rôle d’une interphase élastomère au sein de matériaux composites polyepoxy / renfort de verre (particulaire ou fibreux), Thèse de Doctorat, Institut National des Sciences Appliquées de Lyon, 1989, 335 p. AMER M.S., KOCZAK M.J., SCHADLER L.S., Relating hydrothermal degradation in single fibre composites to degradation behaviour in bulk composites, Composites, 1996, Vol. 27A, pp. 861-867 ANTOON M.K., KOENIG J.L., Fourier-Transform Infrared study of the irreversible interactions of water and a cross-linked epoxy-matrix, J. Polym. Sci., Polym. Phys., 1981, Vol. 19, pp. 1567-1575 APICELLA A., D’AMORE A., MENSITIERI G., NICOLAIS L., Water sorption in thermoplastics and thermosetting matrices for advanced composites, European Symposium on Polymeric Materials, 1st meeting, Lyon-France, September 14-18 1987 GPI08 1-9 ARMISTEAD J.P., SNOW A.W., Influence of matrix properties on fragmentation test, J. Adhesion, 1995, Vol. 52, pp. 209-222 ARORA P.S., MATISONS J.G., PROVATAS A., SMART R.S., Aminohydroxysiloxanes on E-glass fibers, Langmuir, 1995, Vol. 11, pp. 2009-2017 ASHBEE K.H.G., WYATT R.C., Water damage in glass fibre / resin composites, Proc. Roy. Soc., 1969, Vol. A312, pp. 553-564 ASLOUN EL M., DONNET J.B., GUILPAIN G., NARDIN M., SCHULTZ J., On the estimation of tensile strength of carbon fibres at short lengths, J. Mater. Sci., 1989, Vol. 24, pp. 3504-3518 ASLOUN EL M., Etude thermodynamique et mécanique de l'interface et de l'interphase fibre de carbone - poly (Ether Ether Cetone) (PEEK) dans les matériaux composites à hautes performances, Thèse de Doctorat, Université de Haute Alsace, 1991, 173 p. BAHL O.P., MATHUR R.B., DHAMI T.L., Tensile strength of carbon fibres, Polym. Eng. Sci., 1984, Vol. 24, pp. 455-467 BANERJEE A., SUN L., MANTELL S.C., COHEN D., Model and experimental study of fibre motion in wet filament winding, Compos., 1998, Vol. 29A, pp. 251-263 201 Références bibliographiques BANKS L., ELLIS B., The glass transition of an epoxy resin and the effect of absorbed water, Polym. Bull., 1979, Vol. 1, pp. 377-382 BARRERE C., Relations entre les propriétés de la résine et le phénomène de perlage de tubes composites verre – époxy, Thèse de Doctorat, Université de Paris IV, 1998, 206 p. BARTON J.M., GRENNFIELD D.C.L., The use of dynamic mechanical methods to study the effect of absorbed water on temperature-dependant properties of an epoxy resincarbon fibre composite, Brit. Polym. J., 1986, Vol. 18, N°1, pp. 51-56. BASCOM W.D., GWEON S.Y., Fractography and failure mechanisms of polymers and composites. A.C. Roulin-Moloney Ed., London : Elsevier Applied Science, 1989. Ch. 9, Fractography and failure mechanisms of carbon fiber reinforced composite materials, pp. 351386 BEETZ C.P., The analysis of carbon fibre strength distributions exhibiting multiple modes of failure, Fibre Sci. Tech., 1982, Vol. 16, pp. 45-59 BERGMAN B., Estimation of Weibull parameters using a weight function, J. Mater. Sci. Lett., 1986, Vol. 5, pp. 611-614 BERGMAN B., On the estimation of the Weibull modulus, J. Mater. Sci. Lett., 1984, Vol. 3, pp. 689-692 BIAN X.S., AMBROSIO L., KENNY J.M., NICOLAIS L., DIBENEDETTO A.T., Effect of water absorption on the behaviour of E-glass fiber / nylon-6 composites, Polym. Compos., 1991, Vol. 12, N°5, pp. 333-337 BONNIAU P., Effets de l’absorption d’eau sur les propriétés électriques et mécaniques des matériaux composites à matrice organique, Thèse de Doctorat, Ecole Nationale Supérieure des Mines de Paris, 1983, 197 p. BOUKHILI R., HUBERT P., GAUVIN R., Loading rate effect as a function of the span to depth ratio in three bend testing of unidirectionnal pultruded composites, Compos., 1991, Vol. 22, N°1, pp. 39-45 BOWLING J., GROVES G.W. The debonding an pull-out of ductile wires from a brittle matrix, J. Mater. Sci., 1979, Vol. 14, pp. 431-442 BOWLING J., GROVES G.W., The propagation of cracks in composites consisting of ductile wires in a brittle matrix, J. Mater. Sci, 1979, Vol. 14, p. 443-449 BOYER R.F., Mechanical motions in amorphous and semicrystalline polymers, Polymer, 1976, Vol. 17, pp. 996-1008 BRADLEY W.L., Composite Materials Series Vol. 6. R.B. Pipes, K. Fischer Ed., Hamburg : Elsevier, 1989. Ch. 5, Relationship of matrix toughness to interlaminar fracture toughness, pp. 159-188 BRAHATHEESWARAN C., GUPTA V.P., Internal stress in a cured epoxy resin system, Polymer, 1993, Vol. 34, N°2, pp. 289-294 202 Références bibliographiques BREWIS D.M., COMYN J., SHALASH R.J.A., TEGG J.L., Interaction of water with some epoxide adhesives, Polymer Reports, 1980, Vol. 21, pp. 357-360 BROWNING C.E., The mechanisms of elevated property loss in high performance structural epoxy resin matrix materials after exposure to high humidity environments, Polym. Eng. Sci., 1978, Vol. 18, N°1, pp. 16-24 BURGMAN J.A., HUNIA E.M., The effect of fibre diameter, environmental moisture, and cooling time during fibre formation on the strength of E-glass fibres, Glass Technol., 1970, Vol. 11, N°6, pp. 147-152. CARFAGNA C., APICELLA A., NICOLAIS L., The effect of the prepolymer composition of amino-hardened epoxy resins on the water sorption behaviour and plasticization, J. Appl. Polym. Sci, 1982, Vol. 27, pp. 105-112 CARFAGNA C., APICELLA A., Physical degradation by water clustering in epoxy resins, J. Appl. Polym. Sci, 1983, Vol. 28, N°9, pp. 2881-2885 CARSWELL W.S., GEMMEL R., Effect of resin flexibility on the strength of glass filament wound tubes. Part 1: biaxial loading. National Engineering Laboratory Report, Department of Industry, Royaume Uni, 1977, N°643 CARTER H.G., KIBLER K.G., Entropy model for glass transition in wet resins and composites, J. Compos. Mater., 1977, Vol. 11, pp. 265-275 CARTER H.G., KIBLER K.G., Langmuir-type model for anomalous moisture diffusion in composite resins, J. Compos. Mater., 1978, Vol. 12, pp. 118-131 CHAMIS C.C., SINCLAIR J.H., Ten-deg off axis test for shear properties in fiber composites, Experimental Mechanics, 1977, pp. 339-346 CHARLESWORTH J.M., Effect of crosslinking density on molecular relaxations in diepoxyde / diamine network polymers. Part I. The glassy region, Polym. Eng. Sci., 1988, Vol. 28, pp. 221-229. CHATEAUMINOIS A., Comportement viscoélastique et tenue en fatigue statique de composites verre / epoxy. Influence du vieillissement hygrothermique, Thèse de Doctorat, Université Claude Bernard Lyon I, 1991, 209 p. CHENEAU-HENRI P., Evolution avec la température des propriétés de l’interface dans les composites T800H / Bismaléimide, Thèse de Doctorat, Université de Paris 8, 1993, 206 p. CHOU C.T., GAUR U., MILLER B., The effect of microvise gap on microbond pull-out test results, Compos. Sci. Tech., 1994, Vol 51, pp. 111-116 CHRISTIANSEN A.W., LILLEY J., SHORTALL J.B., A three point bend test for fibre reinforced composites, Fiber. Sci. Tech., 1974, Vol. 7 pp. 1-13 COHEN D., Influence of filament winding parameters on composite vessel quality and strength, Compos., 1997, Vol. 28A, pp. 1035-1047 203 Références bibliographiques COHN D., MAROM G., A proposal for a coefficient of hygroelasticity, Polym. Eng. Sci., 1978, Vol. 18, N°13, pp. 1001-1005 COX H.L., The elasticity and strength of paper and other fibrous materials, Brit. J. Appl. Phys., 1952, Vol 3, pp. 72-79 CRANCK J., PARK G.S., Diffusion in Polymers. New York : Academic Press, 1968, 357 p. CRANCK J., The mathematics of diffusion. London : Oxford University Press, 1975, 441 p. CUKIERMAN S., Analyse moléculaire des relaxations entre structure chimique et propriétés dynamiques mécaniques de réseaux époxy modèles, Thèse de Doctorat, Université Paris VI, 1991, 168 p. CULLER S.R., ISHIDA H., KOENIG J.L., FT-IR characterization of the reaction at the silane / matrix resin interphase of composite materials. In 40e Ann. Conf., Reinforced Plastics Composites Institute, The Society of the Plastic Industry Inc., 1985, Vol. 17A, pp. 1-7 CULLER S.R., ISHIDA H., KOENIG J.L., The silane interphase of composites : effect of process conditions on γ-APS, Polym. Compos., 1986 Vol. 7, N°4, pp. 231-238 DAL MASO F., Canalisations en composites – Etude du perlage, Techniques de l’Ingénieur, Traité Plastiques et Composites, 1999, AM 5 551, pp. 1-9 DALY J., BRITTEN A., GARTON A. et al., An additive for increasing the strength and modulus of amine cured epoxy resins, J. Appl. Polym. Sci., 1984, Vol. 29, pp. 1403-1414 DANIELS B.K., HARAKAS N.K., JACKSON R.C., Short beam shear tests of graphite fiber composite, Fiber. Sci. Tech.,1971, Vol. 3, pp. 187-208 DAVIES P., POMIES F., CARLSSON L.A., Influence of water and accelerated aging on the shear fracture properties of glass / epoxy composite, Appl. Compos. Mater., 1996, Vol. 3, pp. 71-87 DAY J.R., MARQUEZ M., The micromechanics of the microbond test. In Interfacial Phenomena in Composite Materials 91, Proceedings of the Second international Conference Leuven (Belgique), September 17-19 1991, Verpoest I., Jones F.(Ed.), Butterworth Heinemann, Science Publishing Co., Inc., 1991, pp. 73-76 DE CHARENTAY F.X., KAMIMURA K., Effet des contraintes de cisaillement fibre / matrice dans les matériaux composites, Annales des composites, 1982, Vol. 24, pp. 332 DE LASI R.J., SCHULTE R.L., Moisture detection in composites using nuclear reaction analysis, J. Compos. Mater., 1979, Vol. 33, pp. 303-308 DE NEVE B., Etude du vieillissement hygrothermique de joints colles adhésif époxydique / aciers : relations entre l’évolution des propriétés mécaniques et les modifications physico-chimiques de l’adhésif et de l’interface, Thèse de Doctorat, Ecole Nationale Supérieure des Mines de Paris, 1993, 260 p. 204 Références bibliographiques DE NEVE B., SHANAHAN M.E.R., Physical and Chemical effects in an epoxy resin exposed to vapour, J. Adhesion, 1995, Vol. 49, pp. 165-176 DELATYCKI O., SHAW J.C., WILLIAMS J.G., Viscoelastic properties of epoxy / amine networks, J. Appl. Polym. Sci., 1969, Vol. 7, pp. 753-762 DERAMBURE J.L., Etude de l’hydrolysabilité de molécules modèles des résines époxydiques, Thèse de Doctorat, Université de Bordeaux-1, 1996, 182 p. DEWIMILLE B., Vieillissement hygrothermique d’un matériau composite fibres de verre-résine époxyde, Thèse de Doctorat, Ecole Nationale Supérieure des Mines de Paris, 1981, 189 p. DHAOUI W., Relations structure / propriétés des réticulats époxyde / amine, Thèse de Doctorat, Ecole Nationale Supérieure d'Arts et Métiers, 1988, 151 p. DI FRANCIA C., WARD T.C., CLAUS R.O., The single-fibre pull-out test. 1. Review and interpretation, Compos., 1996, Vol. 27A, pp. 597-612 DI FRANCIA C., WARD T.C., CLAUS R.O., The single-fibre pull-out test. 2.Quantitative evaluation of an uncatalysed TGDDM/DDS epoxy cure study, Compos., 1996, Vol. 27A, pp. 613-624 DIAMANT Y., MAROM G., BROUTMAN L.J., The effect of network structure on moisture absorption of epoxy resins, J. Appl. Polym. Sci., 1981, Vol. 26, pp. 3015-3027 DIBENEDETTO A.T., LEX P.J., Evaluation of surface treatments for glass fibers in composite materials, Polym. Eng. Sci., 1989, Vol. 29, N°8, pp. 543-555 DIBENEDETTO A.T., Measurement of the thermomechanical stability of interphases by the embedded single fiber test, Compos. Sci. Tech., 1991, Vol. 42, pp. 103-123 DIBENEDETTO A.T., SCOLA D.A., Characterization of S-glass / polymer interfaces using scattering spectroscopy and scattered ions mass spectroscopy, J. Coll. Inter. Sci., 1978, Vol. 64, N°3, pp. 480-500 DIXON R.R., Measuring moisture by dielectric analysis, SPI 37th ANTEC New Orleans, 1979, pp. 835-836 DOUGLASS D.A., WEITSMAN Y., Stresses due to environmental conditionning of cross-ply graphite-epoxy laminates. In Advances in Composites Materials, Proceeding of ICCM 3, 1980, Vol. 1, pp. 85-98 DROWN E.K., MOUSSAWI H.AL., DRZAL L.T., Glass fiber sizing and their role in fiber-matrix adhesion, J. Adh. Sci. Tech., 1991, Vol. 5, N°10, pp. 865-881 DUSEK K., Are cured thermoset resins inhomogeneous ?, Die Angewandte Makromolekulare Chemie, 1996, Vol. 240, pp. 1-15 DUSEK K., BLEHA M., LUNAK S., Curing of epoxide resins : Model reactions of curing with amine, J. Polym. Sci., Polym. Chem. Ed., 1977, Vol. 15, pp. 2393-2400 205 Références bibliographiques DUSEK K., PLESTIL J., LEDNICKY F., LUNAK S., Are cured epoxy resins inhomogeneous ?, Polymer, 1978, Vol. 19, pp. 393-397 EAKINS W.J., A restrained layer at the glass – resin interface ?, Proc., 20th Anniversary Conf., Reinforced Plastic Division, Soc. of the Plastic Industry, 1965, Vol. 15C, pp. 158-167 EAKINS W.J., Effect of water on glass fiber – resin bonds, Interfaces in Composites Materials, ASTM STP 452, American Society for Testing and Materials, 1969, pp. 137-148 ECKSTEIN Y., Role of the silane in adhesion Part I. Dynamic mechanical properties of silane coatings on glass fibres, J. Adhesion Sci. Technol., 1988, Vol. 2, N°5, pp. 339-348 EMADIPOUR H., CHIANG P., KOENIG J.L., Interfacial strength studies of fibrereinforced composites, Res. Mechanica, 1982, Vol. 5, pp 165-176 ENNS J.B., GILLHAM J.K., Effect of the extent of cure on the modulus, glass transition, water absorption and density of an amine-cured epoxy, J. Appl. Polym. Sci., 1983, Vol. 28, pp. 2831-2840 EUSTACHE R.P., LAUPRETRE R., CUKIERMAN S., HALARY J.L., MONNERIE L., FERNAGUT F., LEFEBVRE J.M., ESCAIG B., Investigation of the molecular processes involved in the plastic deformation of model epoxy networks, 8th Int. Conf. On Deformation, Yield and Fracture of Polymers, Cambridge (GB), 1991, april 8-11 FAVRE J.P., DEWAS J.N., Diffusion d’eau dans les composites carbone-époxyde. Test d’un modèle basé sur l’absorption d’eau dans la matrice, Comptes Rendus des Quatrièmes Journées Nationales sur les Composites, JNC4, Paris, 11-13 septembre 1984, pp. 615-630 FEILLARD P., Contribution à l’étude micromécanique de l’interface et des phénomènes élémentaires d’endommagement dans les composites modèles fibre de verre / résine époxyde, Thèse de Doctorat, Institut National des Sciences Appliquées de Lyon, 1993, 164 p. FEILLARD P., DESARMOT G., FAVRE J.P., A critical assessment of the fragmentation test for glass / epoxy systems, Compos. Sci. Tech., 1993, Vol. 49, pp. 109-119 FELLER J.F., Interphase modèle dans un composite polypropylène / fibre de verre à partir de la synthèse de nouveaux agents de couplage, Thèse de Doctorat, Université Claude Bernard Lyon I, 1995, 194 p. FIGUEROA J.C., CARNEY T.E, SCHADLER L.S., LAIRD C., Micromechanics of single filament composites, Compos. Sci. Tech., 1991, Vol. 42, pp. 77-101 FISCHER S., ROMAN I., HAREL H., MAROM G., WAGNER H.D., Simultaneous determination of shear and Young’s moduli in composites, J. Test. Eval., JTEVA, 1981, Vol. 9, N°15, pp. 303-307 FOX T.G., Influence of diluent and of copolymer composition on the glass temperature of a polymer system, Bull. Amer. Phys. Soc., 1956, Vol. J5, p. 1123 206 Références bibliographiques FULLER R.T., FORNES R.E., MEMORY J.D., NMR study of water absorbed by epoxy resin, J. Appl. Polym. Sci., 1979, Vol. 23, pp. 1871-1874 FULLER R.T., SHERROW S., FORNES R.E., MEMORY J.D., Hydrogen exchange between water and epoxy resin, J. Appl. Polym. Sci., 1979, Vol. 24, pp. 1383-1385 GANEM M., MORTAIGNE B., BELLENGER V., VERDU J., Rev. Sci. Tech. de la Défense, numéro spécial bicentenaire, 1994, pp. 198-213 GAO Y.C., MAI Y.W., COTTEREL B., Fracture of fiber reinforced materials, J. Appl. Mathematic Phys. (ZAMP), 1988, Vol. 39, pp. 550-572 GAUR U., CHOU C.T., MILLER B., Effect of hydrothermal ageing on bond strength, Compos., 1994, Vol. 25, N°7, pp 609-612 GAUR U., MILLER B. Microbond method for determination of the shear strength of a fiber / resin interface : Evaluation of experimental parameters, Compos. Sci. Tech., 1989, Vol 34, pp. 35-51 GAUR U., MILLER B., Effects of environmental exposure on fiber / epoxy interfacial shear strength, Polym. Compos., 1990, Vol. 11, N°4, pp 217-222 GAZIT S., Dimensional changes in glass filled epoxy resins as a result of absorption of atmospheric moisture, J. Appl. Polym. Sci., 1978, Vol. 22, pp. 3547-3558 GHOSH P., BOSE N.R., FRP composites based on different types of glass fibers and matrix resins : a comparative study, J. Appl. Polym. Sci., 1995, Vol. 58, pp. 2177-2184 GOMEZ J.A., KILGOUR J.A., The effect of surface coatings on fiber strengths and the distribution of flaws, Osi Specialities, 1993, Note Technique, 15 p. GONON L., MOMTAZ A., VAN HOYWEGHEN D., CHABERT B., GERARD J.F., GAERTNER R., Physicochemical and micromechanical analysis of the interface in a poly(phenylene sulfide) / glass fiber composite – A microbond study, Polym. Compos., 1996, Vol. 17, N°2, pp. 265-274 GRAVE C., McEWAN I., PETHRICK R.A., Influence of stochiometric ratio on water absorption in epoxy resins, J. Appl. Polym. Sci., 1998, Vol. 69, pp. 2369-2376 GRAY R.J. Analysis of the effect of embended fiber length on fiber debonding and pull-out from an elastic matrix. Review of theories, J. Mater. Sci., 1984, Vol 19, pp. 861-870 GREENWOOD J.H., German work on GRP design, Composites, 1977, Vol. 8, pp. 175-184 GRESZCZUK L.B. Theoretical studies of the mechanics of the fiber-matrix interface in composites, Interfaces in composites, ASTM STP 452, American Society for testing and materials, 1969, pp.42-58 GUPTA V.B., DRZAL L.T., LEE C.Y.C., RICH M.J., The temperature dependance of some mechanical properties of a cured epoxy resin system, Polym. Eng. Sci., 1985, Vol. 25, N°13, pp. 812-823 207 Références bibliographiques HAHN H.T., Hygrothermal damage in graphite / epoxy laminates, J. Eng. Mater. Tech., 1987, Vol. 109, pp. 3-9 HALARY J.L., CUKIERMAN S., MONNERIE L., Influence de la prise d’humidité sur les propriétés dynamiques mécaniques de réseaux epoxy modèles, Annales des Composites, 1992, Vol. 1-2, pp. 103-112 HALPIN J.C., KARDOS J.L., The Halpin-Tsaï equations : a review, Polym. Eng. Sci., 1976, Vol. 16, N°5, pp. 344-352 HAMADA H., KODOMOTO S., Determination of interfacial materials constants of glass/epoxy composite, J. Mater. Sci. Lett., 1997, Vol. 16, pp. 179-180 HATA N., KUMANOTANI J., Viscoelastic properties of epoxy resins. Effect of prepolymer structure on viscoelastic properties, J. Appl. Polym. Sci., 1971, Vol. 15, pp. 23712380 HATA N., YAMAUCHI R., KUMANOTANI J., Viscoelastic properties of epoxy resins. II Antiplasticization in highly crosslinked epoxy system, J. Appl. Polym. Sci., 1973, Vol. 17, pp. 2173-2181 HEISEY C.L., WOOD P.A., MCGRATH J.E., WIGHTMAN J.P., Measurement of adhesion between carbon fibers and bismaleimide resins, J. Adhesion, 1995, Vol.53, pp. 117-147 HERRERA-FRANCO P.J., DRZAL L.T. Comparison of methods for the measurement of fibre/matrix adhesion in composites, Compos., 1992, Vol 23, pp. 2-27 HODZIK A., KALYANASUNDARAM S., LOWE A., STACHURSKI Z., Analysis of microdroplet – single fibre test for composite materials, Proc. 37th Int. Symp. On Macromolecules, IUPAC, Gold Coast (Australia) 12-17 July 1998, p. 558 HODZIK A., KALYANASUNDARAM S., LOWE A., STACHURSKI Z.H., The microdroplet test : experimental and finite element analysis of the dependence of failure mode on droplet shape, Compos. Inter., 1999, Vol. 6, N°4, pp. 375-389 HOH K., ISHIDA H., KOENIG J.L., Multi-nuclear NMR spectroscopic and proton imaging studies on the effect of water on the silane coupling agent/matrix interface in glass fiber - reinforced composites, Polym. Compos., 1990, Vol. 11, N°3, pp. 192-199 HOH K.P., ISHIDA H., KOENIG J.L., Spectroscopic studies of the gradient in the silane coupling agent / matrix interface in fiberglass reinforced epoxy, Polym. Compos., 1988, Vol. 9, N°2, pp. 151-157 HSUEH C.H., Elastic load transfer from partially embedded axially loaded fibre to matrix, J. Mater. Sci. Lett., 1988, Vol. 7, pp. 497-500 HSUEH C.H., Interfacial debonding and fiber pull-out stresses of fiber-reinforced composites, Mater. Sci. Eng., 1990, Vol. A123, pp. 1-11 208 Références bibliographiques HSUEH C.H., Interfacial debonding and fiber pull-out stresses of fiber-reinforced composites II : Non-constant interfacial bond strength, Mater. Sci. Eng, 1990, Vol. A125, pp. 67-73 ISHIDA H., A review of recent progress in the studies of molecular and microstructure of coupling agents and their functions in composites, coatings and adhesive joints, Polym. Compos., 1984, Vol. 5, N°2, pp. 101-123 ISHIDA H., CHIANG C., KOENIG J.L., The structure of aminofunctional silane coupling agents : 1. γ-APS and its analogues, Polymer, 1982, Vol. 23, pp. 251-257 ISHIDA H., KOENIG J.L., A fourier – transform infra-red spectroscopic study of the hydrolytic stability of the silane coupling agents on E-glass fibers, J. Appl. Polym. Sci., 1980, Vol. 18, pp. 1931-1943 ISHIDA H., NAVIROJ S., TRIPATHY S.K., FITZERALD J.J., KOENIG J.L., The structure of an aminosilane coupling agent in aqueous solutions and partially cured solids, J. Polym. Sci., Polym Phys Ed., 1982, Vol. 20, pp. 701-718 JEANNE P., Contribution à l’étude des zones interfaciales dans les composites polyépoxyde – fibres de verre, Thèse de Doctorat, Ecole Centrale de Lyon, 1986, 253 p. JELINSKY L.W., DUMAIS J.J., STARK R.E., ELLIS T.S., KARASZ F.E., Interaction of epoxy resins with water. A quadrupole echo deuterium NMR study, Macromolecules, 1983, Vol. 16, pp. 1019-1021 JELINSKY L.W., DUMAIS J.J., STARK R.E., ELLIS T.S., KARASZ F.E., Nature of the water-epoxy interaction, Macromolecules, 1985, Vol. 18, pp. 1091-1095 JONES C.J., DICKSON R.F., ADAM T., REITER H., HARRIS B., The environmental fatigue behaviour of reinforced plastics, Proc. Roy. Soc., 1984, Vol. A396, pp. 315-337 JONES F.R., Interphase formation in fibre composite materials, Key Eng. Mater., 1996, Vol. 116-117, pp. 41-59 JONES M.L.C., HULL D., Microscopy of failure mechanisms in filament-wound pipe, J. Mater. Sci., 1979, Vol. 14, pp. 165-174 JORDAN W.M., BRADLEY W.L., Micromechanics of fracture in toughened graphite epoxy laminates. Toughened Composites, ASTM STP 937. Edited by N.J. Johnston, Philadelphia: American Society for Testing Materials, 1987, pp. 95-114 KAELBLE D.H., DYNES P.J., CRANE L.W., Interfacial mechanisms of moisture degradation in epoxy-graphite composites, J. Adhesion., 1975, Vol. 7, N°1, pp. 25-54 KAELBLE D.H., DYNES P.J., MAUS L., Hydrothermal aging of composite materials. Part 1: interfacial aspects, J. Adhesion, 1976, Vol. 8, pp. 121-144 KEENAN J.D., SEFERIS J.C., Effects of moisture and stoechiometry on the dynamic mechanical properties of a high performance structural epoxy, J. Appl. Polym. Sci., 1979, Vol. 24, pp. 2375-2381 209 Références bibliographiques KELLEY F.N., BUECHE F., Viscosity and glass temperature relations for polymerdiluent systems, J. Polym. Sci., 1961, Vol. L, 549-556 KELLY A., TYSON W.R., Tensile properties of fibre reinforced metals : Copper / Tungsten and Copper / Molybdenum, J. Mech. Phys. Solids, 1965, Vol. 13, pp. 329-350. KELLY A., TYSON W.R., Tensile properties of fibre reinforced metals -II: Creep of silver - tungsten, J. Mech. Phys. Solids, 1966, Vol. 14, pp. 177-186. KIM J.K., BAILLIE C., MAI Y.W., Interfacial debonding and fibre pull-out stresses. Part I. Critical comparison of existing theories with experiments, J. Mater. Sci., 1992, Vol. 27, pp. 3143-3154 KOENIG J.L., EMADIPOUR H., Mechanical characterization of the interfacial strength of glass - reinforced composites, Polym. Compos., 1985, Vol. 6, N°3, pp 142-150 KONDO K., TAKI T., Moisture diffusivity of unidirectionnal Composites, J. Compos. Mater., 1982, Vol. 16, pp. 82-93 KONG E.S.W., ADAMSON M.J., Physical ageing and its effect on the moisture sorption of amine cured epoxy, Polymer Comm., 1983, Vol. 24, pp. 171-173 LACHENAL G., Structural investigations and monitoring of polymerisation by NIR spectroscopy, J. NIR Spectroscopy., 1998, Vol. 6, pp. 299-306 LACRAMPE V., Influence du type d’ensimage sur la nature des zones interfaciales dans les matériaux composites polyepoxy / fibres de verre, Thèse de Doctorat, Institut National des Sciences Appliquées de Lyon, 1992, 291 p. LASNE M., NAGOT F., PAYS M.F. et al., Matériaux composites : de bons tuyaux pour les circuits de sûreté des centrales nucléaires?, Epure, Direction des Etudes et Recherches EDF, 1999, N°61, pp. 15-27 LAWING D., FORNES R.E., GILBERT R.D., MEMORY J.D., Temperature dependance of broadline NMR spectra of water soaked epoxy graphite composites, J. Appl. Phys., 1981, Vol. 52, N°10, pp. 5906-5912 LAWRENCE P. Some theoretical considerations of fibre pull-out from an elastic matrix, J. Mater. Sci., 1972, Vol 7, pp. 1-6 LEROY F.H., Rupture des composites unidirectionnels à fibres de carbone et matrice thermodurcissable : approche micro-macro, Thèse de Doctorat, Université de Bordeaux I, 1996, 226 p. LEUKEL J., BURCHARD W., Mechanism of the anionic copolymerization of anhydride cured epoxies – analyzed by matrix-assisted laser desorption ionization time-offlight mass spectroscopy (MALDI-TOF-MS), Macromol. Rapid Commun., 1996, Vol. 17, pp. 359-366 LUBLIN G., DONOHUE P., Real life properties of composites, SP1 31 1980 Section 17E 1-13 210 th ANTEC, Références bibliographiques MACANDER A., SILVERGLEIT M., The effect of a marine environment on stressed and unstressed graphite-epoxy composite, Naval Eng. J., 1977, Vol. 89, N°4, pp. 6572 MADHUKAR M.S., DRZAL L.T., Fiber matrix adhesion and its effect on composite mechanical properties : IV. Mode I and mode II fracture toughness of graphite / epoxy composites, J. Compos. Mater., 1992, Vol. 26, N°7, pp. 936-968 MAGGANA C., PISSIS P., Water absorption and diffusion in an epoxy resin system, J. Polym. Sci., Polym Phys., 1999, Vol. 37, pp. 1165-1182 MAI C., GERARD J.F., Matériaux hybrides. Paris : Masson 1996. Ch. IIIA, Propriétés mécaniques des matériaux hybrides inorganiques-organiques, pp. 91-113 MAI K., MAEDER E., MUEHLE M., Interphase characterization in composites with non-destructive methods, Compos., 1998, Vol. 29A, pp. 1111-1119 MAROM G., Composite Materials Series Vol. 6. R.B. Pipes, K. Fischer Ed., Hamburg: Elsevier, 1989. Ch. 10 Environmental effects on fracture mechanical properties of polymer composites, pp. 397-424 MAROM G., Polymer permeability. J. Comyn Ed., New York: Elsevier applied science publishers LTD, 1985. Ch. 9, The role of water transport in composite materials, pp. 341-374 MAROM G., Swelling and hygroelasticity of polymeric composites, Polym. Eng. Sci., 1977, Vol. 17, N°11, pp. 799-802 MAROTZKE C., Determination of the stress field in the single fiber pull-out test with the aid of the finite element method, In Interfacial Phenomena in Composite Materials 91, Proceedings of the Second international Conference Leuven (Belgique), September 17-19 1991, Verpoest I., Jones F.(Ed.), Butterworth Heinemann, Science Publishing Co., Inc., 1991, pp. 69-72 MAROTZKE C., HAMPE A., Fracture mechanical analysis of pull-out and fragmentation tests, Proc. ICCM-11, Gold Coast, Australia, 14-18 july 1997, pp. V-863 - V872 MAROTZKE C., The elastic stress field arising in the single fiber pull-out test, Compos. Sci. Tech., 1994, Vol. 50, pp. 393-405 MATEJKA L., LOVY J., POKORNY S., BOUCHAL K., DUSEK K., Curing epoxy resins with anhydrides. Model reaction and reaction mechanism, J. Polym. Sci., Polym Chem. Ed., 1983, Vol. 21, pp. 2873-2885 MATEJKA L., POKORNY S., DUSEK K., Acid curing of epoxy resins. A comparison between the polymerization of diepoxide-diacid and monoepoxide-cyclic anhydride systems, Makromol. Chem., 1985, Vol. 186, pp. 2025-2036 MAY C.A., TANAKA Y., Epoxy resins chemistry and technology. New York : Dekker, M. Inc., 1973, 801 p. 211 Références bibliographiques McCARTNEY L.N., New theoretical model of stress transfer between fibre and matrix in a uniaxially fibre reinforced composite, Proc. Roy. Soc., 1989, Vol. A425, pp. 215244 McDONOUGH W.G., ANTONUCCI J.M., DUNKERS J.P., Evaluation of dental adhesion and durability by means of the microbond test, Proc. 21st annual Meeting of the Adhesion Society, Savannah, Georgia, Feb. 22-25, 1998, pp. 129-131 McKAGUE E.L., REYNOLDS J.D., HALKIAS J.E., Swelling and glass transition relations for epoxy matrix materials in humid environments, J. Appl. Polym. Sci, 1978, Vol. 22, pp. 1643-1654 MENGES G., GITSCHNER H.W., Sorption behaviour of glass fiber reinforced composites an dthe influence of diffusion media on deformation and failure behaviour, Proceeding of . ICCM 3, 1980, Vol. 1, pp. 25-48 METCALFE A.G., SCHMITZ G.K., Effect of length on the strength of glass fibers, Proceedings, American Society of Testing Materials, 1964, Vol. 64, pp. 1075-1093 MIERAS H.J.M.A., Irreversible creep of filament wound glass reinforced resin pipes, Plastics and Polymers, 1973, Vol. 41, pp. 84-88 MIJOVIC J., Time dependant changes in mechanical properties of neat and reinforced epoxy resins, J. Appl. Polym. Sci; 1982, Vol. 27, pp. 2919-2931 MIJOVIC J., TSAI L., Correlations between dynamic mechanical properties and nodular morphology of cured epoxy resins, Polymer, 1981, Vol. 22, pp. 902-906 MIKOLS W.J., SEFERIS J.C., APICELLA A., NICOLAIS L., Evaluation of structural changes in epoxy systems by moisture sorption – desorption and dynamic mechanical studies, Polym. Compos., 1982, Vol. 3, N°3, pp. 118-127 MILLER B., GAUR U., HIRT D.E. Measurement and mechanical aspect of the microbond pull-out technique for obtaining fiber / resin interfacial shear strength, Compos. Sci. Tech., 1991, Vol. 42, pp. 207-219 MILLER D.G., The use of DMA for characterization of organic coatings on multiple glass fiber strands, American Laboratory, 1982, pp. 21-26 MIN B.G., SHIN D.K., STACHURSKI Z.H., HODGKIN J.H., A study of water absorption characteristics of DGEBA / DDS resin system using near infrared spectroscopy, Polymer Bull., 1994, Vol. 33, pp. 465-470 MONETTE L., ANDERSON M.P., GREST G.S., The meaning of the critical length concept in composites : study of matrix viscosity and strain rate on the average fiber fragmentation length in short - fiber polymer composites, Polym. Compos., 1993, Vol. 14, N°2, pp. 101-115 MOON C.K., LEE J., CHO H.H. et al. Effect of diameter and surface treatment of fiber on interfacial shear strength in glass fiber/epoxy and HDPE, J. Appl. Polym. Sci., 1992, Vol. 45, pp. 443-450 212 Références bibliographiques MOREL E., BELLENGER V., VERDU J., Structure water absorption relationship for amine cured epoxy resins, Polymer, 1985, Vol. 26, pp. 1719-1724 MORGAN R.J., KONG F.M., WALKUP C.M., Structure property relations of polyethertriamine-cured bisphenol-A diglycidyl ether epoxies, Polymer, 1984, Vol. 25, pp. 375-384 MORGAN R.J., MONES E.T., The effect of thermal environment and sorbed moisture on the durability of epoxies, 11th National SAMPE Technical Conference, November 13-15, 1979, pp. 218-232 MORGAN R.J., O’NEAL J.E., The durability of epoxies, Polym. Plast. Technol Eng., 1978, Vol. 10, N°1, pp. 49-116 MOUSSAWI H.AL., DROWN E.K., DRZAL L.T., The silane / sizing composite interphase, Polym. Compos., 1993, Vol. 14, N°3, pp. 195-200 MOY P., KARASZ F.E., Epoxy-water interactions, Polym. Eng. Sci., 1980, Vol. 20, N°4, pp. 315-319 NAIRN J.A., A variational mechanics analysis of the stresses around breaks in embedded fibers, Mech. Mater., 1992, Vol. 13, N°2, pp. 131-154 NAIRN J.A., LIU Y.C., Stress transfer into a fragmented, anisotropic fiber through an imperfect interface, Int. J. Solids Struct., 1997, Vol. 34, N°10, pp. 1255-1281 NAIRN J.A., Thermoelastic analysis of residual stresses in unidirectionnal high performance composites, Polymer Composites, 1985, Vol. 6, N°2, pp. 123-130 NARKIS M., CHEN E.J.H., PIPES R.B., Review of methods for characterization of interfacial fiber - matrix interactions, Polym. Compos., 1988, Vol. 9, N°4, pp. 245-251 NETRAVALI A.N., SCHWARTZ P., PHOENIX S.L., Study of interfaces of highperformance glass fibers and DGEBA-based epoxy resins using single-fiber-composite test, Polym. Compos., 1989, Vol. 10, N°6, pp. 385-388 OCHI M., IESAKO H., NAKAJIMA S. et al., Mechanical relaxation mechanism of epoxyde resins cured with acid anhydrides. II. Effect of the chemical structure of the anhydrides on the β relaxation mechanism, J. Polym. Sci, Polym. Phys. Ed., 1986, Vol. 24, pp. 251-261. OCHI M., IESAKO H., SHIMBO M., Mechanical relaxation mechanism of epoxide resins cured with diamines, Polymer, 1985, Vol. 26, pp. 457-461 OCHI M., IESAKO H., SHIMBO M., Relaxations mechanisms of epoxyde resins cured with acid anhydrides. III. Effect of alkyl side chains on mechanical and dielecric β relaxations, J. Polym. Sci. Part B, Polym. Phys., 1986, Vol. 24, pp. 1271-1282 OCHI M., KAGEYAMA H., SHIMBO M., Mechanical and dielectric relaxations of poly(hydroxyethers) : 1. Low temperature relaxations, Polymer, 1988, Vol. 29, pp. 320-324 213 Références bibliographiques OCHI M., SHIMBO M., SAGA M., TAKASHIMA N., Mechanical and dielectric relaxations of epoxide resins containig the spiro-ring structure, J. Polym. Sci., Polym. Phys., 1986, Vol. 24, pp. 2185-2195 OCHI M., YAMASHITA K., SHIMBO M., The mechanism for occurrence of internal stress during curing epoxide resins, J. Appl. Polym. Sci., 1991, Vol. 43, pp. 20132019 OCHI M., YOSHIZUMI M., SHIMBO M., Mechanical and dielectric relaxations containing the spiro-ring structure. II. Effect of the introduction of methoxy branches on low temerature relaxations of epoxy resins. J. Polym. Sci., Polym. Physics, 1987, Vol. 25, pp. 1817-1827 OCHI M., ZHU S., SHIMBO M., Mechanical relaxation properties of spiro-type epoxyde resins cured with acid anhydrides, Polymer, 1986, Vol. 27, pp. 1569-1573 ONDRUS D.J., BOERIO F.J., GRANNEN K.J., Molecular structure of polymer metal interphases, J. Adhesion, 1989, Vol. 29, pp. 27-38 OSHAWA T., NAKAYAMA A., MIWA M., HASEGAWA A., Temperature dependence of critical fiber length for glass fiber – reinforced thermosetting resins, J. Appl. Polym. Sci., 1978, Vol. 22, pp. 3203-3212 OSTERHOLZ F.D., POHL E.R., Kinetics of the hydrolysis and condensation of organofunctional alkoxysilanes : a review, J. Adh. Sci. Tech., 1992, Vol. 6, N°1, pp. 127-149 OUTWATER J.O., MURPHY M.C. On the fracture energy of unidirectional laminates Paper presented at "24th annual Technical Conf.", Reinforced Plastic Composites Division, The Society of Plastic Industry Inc., 1969, Section 11-C, p. 1-8 PABIOT J., KRAWCZAK P., MONNIER C., Behaviour of glass fiber pipes under internal pressure as a function of composite cohesion parameters, 49th annual Conference, Composites Institute, The Society of the Plastic Industry Inc., 1994, 7-9 février. PASCAULT J.P., Matériaux hybrides. Paris : Masson 1996. Ch. IIB, Polymères et hybrides organiques-inorganiques, pp. 59-74 PAWLAK A., GALESKI A., Measurements of characteristic parameters in polymer composites by means of a micropolariscope, Optical Engineering, 1995, Vol. 34, N°12, pp. 3398-3404 PAWLAK A., GALESKI A., Photoelastic method of three-dimensionnal stress determination around axisymetric inclusions, Polym. Eng. Sci., 1996, Vol. 36, N°22, pp. 2736-2749 PAWLAK A., GALESKI A., Residual stresses in epoxy systems by 3-D photoelastic method, Polym. Eng. Sci., 1996, Vol. 36, N°22, pp. 2727-2735 PAWSON D., JONES F.R., The effect of sodium ions on the stability of the interphase region of glass fibre reinforced composites, J. Adhesion, 1995, Vol. 52, pp. 187207 214 Références bibliographiques PENN L.S., CHOU C.T., Identification of factors affecting single filament pull-out test results, J. Compos. Tech. Res., 1990, Vol. 12, N°3, pp.164-171 PENN L.S., LEE S.M., Interpretation of experimental results in the single pull-out filament test, J. Compos. Tech. Res, 1989, Vol. 11, N°1, pp. 23-30 PERRET P., Caractérisation des réseaux polyepoxy, étude des zones interfaciales dans les composites unidirectionnels fibres de carbone / matrice polyepoxy DGEBA-DDM, Thèse de Doctorat, Institut National des Sciences Appliquées, 1988, 222 p. PETROVIC Z., STOJAKOVIC., Study of epoxy resin/filler interaction, Polym. Compos., 1988, Vol. 9, N°1, pp. 42-50. PHILIBERT J., Diffusion et transport de matière dans les solides. Paris : Les éditions de physique, 1990. Chap 1 : Diffusion et transport, pp. 8-69. PIERRE A., Aptitude à la déformation de polymères thermodurcissables appliqués en couche mince sur un substrat métallique, Institut National des Sciences Appliquées, 1997, 159 p. PIGGOTT M.R. Debonding and friction at fiber-polymer interface : I Criteria for failure and sliding, Compos. Sci. Tech., 1987, Vol 30, pp.295-306 PLUEDDEMANN E.P., Silane coupling agents. New York : Plenum Press, 1982, 235 p. POGANY G.A., Gamma relaxation in epoxy resins and related polymers, Polymer, 1970, Vol. 11, pp. 66-78. PUCK A., SCHNEIDER W., On failure mechanisms and failure criteria of filament wound glass fibre / resin composite, Plastics and Polymers, 1969, Vol. 37, pp. 33-44 RAO V., DRZAL L.T., The temperature dependence of interfacial shear strength for various polymeric matrices reinforced with carbon fibers, J. Adhesion., 1992, Vol. 37, pp. 8395 RAO V., HERRERA-FRANCO P., OZZELO A.D., DRZAL L.T., A direct comparison of the fragmentation test and the microbond pull-out test for determining the interfacial shear strength, J. Adhesion., 1991, Vol. 34, pp. 65-77 ROBESON L.M., CRISAFULLY S.T., Microcavity formation in engineering polymers exposed to hot water, J. Appl. Polym. Sci., 1983, Vol. 28, pp. 2925-2936 ROSEN B.W., Fiber Composite Material. Ohio : ASM, Metals Park, 1965. Ch. 3 Mechanic of composite strengthening, pp. 37-75 ROSENSAFT M., MAROM G., Evaluation of bending test methods for composites materials, J. Compos. Tech. Res., 1985, Vol. 7, N°1, pp. 12-16 ROUBY D., Application de l’émission acoustique à la caractérisation micromécanique de l’interface fibre / matrice, C.R des 6e Journées Nationales sur les Composites, JNC 6, Paris, 11-13 Octobre 1988, pp. 183-194 215 Références bibliographiques ROUBY D., FAVRE J.P., Studies of fibre failure in a single carbon fiber epoxy composite by using acoustic emission, 16th European Working Group and Acoustic Emission (EWGAE), London, Septembre 16-17, 1987. SABRA A.H., Etude des caractéristiques des réseaux époxydes d’enrobage appliqués aux condensateurs pour télécommunications, Thèse de Doctorat, Institut National des Sciences Appliquées de Lyon, 1985, 226 p. SALMON L., Etude de la dégradation hydrolytique de l’interface fibre – matrice dans les matériaux composites fibres de verre – résine époxyde, Thèse de Doctorat, Ecole Nationale Supérieure des Arts et Métiers, 1997, 138 p. SANADI A.R., SUBRAMANIAN R.V., MANORANJAN V.S., The interphasial regions in interlayer fiber composites, Polym. Compos., 1991, Vol. 12, N°6, pp. 377-383 SANCHEZ C., BABONNEAU F., Matériaux hybrides. Paris: Masson 1996. Ch. IIA, Chimie des matériaux hybrides élaborés par la méthode sol-gel, pp. 33-58 SCHEER R.J., NAIRN J.A. A comparison of several mechanics methods for measuring interfacial toughness with microbond tests, J. Adhesion, 1995, Vol. 53, pp. 45-68 SCHMITZ G.K., METCALFE A.G., Testing of fibres, Materials Research and Standarts, 1967, Vol 7, N°4, pp. 146-152. SCHROEDER J.A., MADSEN P.A., FOISTER R.T., Structure-property relationships for a series of crosslinked aromatic / aliphatic epoxy mixtures, Polymer, 1987, Vol. 28, N°5, pp. 929-940 SCHULZ U., KAISER N., Near-infrared spectroscopy for monitoring water permeability of optical coatings on plastics, Applied Optics, 1997, Vol. 36, N°4, pp. 862-865 SCHUTTE C.L., McDONOUGH W., SHIOYA M., McAULIFFE M., GREENWOOD M., The use of a single-fibre fragmentation test to study environmental durability of interfaces / interphases between DGEBA/mPDA epoxy and glass fibre: The effect of moisture, Compos., 1994, Vol. 25, N°7, pp. 617-624 SERIER A., Etude du système prépolymère époxyde / γ-APS : réactions – propriétés et application aux matériaux composites, Thèse de Doctorat, Institut National des Sciences Appliquées de Lyon, 1989, 208 p. SERIER A., PASCAULT J.P., LAM T.M., Reactions in aminosilane-epoxy prepolymer systems. II. Reactions of alkoxysilane groups with or without the presence of water, J. Appl. Polym. Sci., 1991, Vol. 29, pp. 1125-1131 SHEN C.H., SPRINGER G.S., Effects of moisture and temperature on the tensile strength of composite materials, J. Compos. Mater., 1977, Vol. 11, pp. 2-16 SHEN C.H., SPRINGER G.S., Environmental effects on the elastic moduli of composite materials, J. Compos. Mater., 1977, Vol. 11, pp. 250-264 SHEN C.H., SPRINGER G.S., Moisture absorption and desorption of composite materials, J. Compos. Mater., 1976, Vol. 10, pp. 2-20 216 Références bibliographiques SHIMBO M., OCHI M., ARAI K., Internal stresses of cured epoxide resin coatings having different network chains, J. Coat. Technol., 1984, Vol. 56, pp. 45-51 SHIMBO M., OCHI M., IESAKO H., Mechanical relaxation mechanism of epoxyde resins cured with acid anhydrides J. Polym. Sci. Part B, Polym. Phys. Ed., 1984, Vol. 22, pp. 1461-1470 SOLES C.L., CHANG F.T., BOLAN B.A., HRISTOV H.A., GIDLEY D.W., YEE A.F., Contribution of the nanovoid structure to the moisture absorption properties of epoxy resins, J. Polym. Sci., Polym. Phys. Ed., 1998, Vol. 36, pp. 3035-3048 STANG H., SHAH S.P., Failure of fibre reinforced composites by pull-out fracture, J. Mater. Sci., 1986, Vol. 21, pp. 953-957. STUETZ D.E., SULLIVAN R.E., EDWARDO A.D., HARDY G., RECCA O.D., Effect of moisture on chemical interaction of a polymer-fiber interface, New Jersey: 1979 Report AFML-TR-77 pp. 214-226 SUZUKI N., ISHIDA H., A review on the structure and characterization techniques of silane / matrix interphases, Macromol. Symp., 1996, Vol. 108, pp. 19-53 TAKAHAMA T., GEIL P.H., The β relaxation behaviour of bisphenol type resins. J. Polym. Sci., 1982, Vol. 20, pp. 1979-1986. TAKAHAMA T., WU C.S., CHEN A. et al., Low temperature relaxation behaviour of epoxy resins. Polymer Composites. B. Sedlacek Ed., Berlin: Walter de Gruyter and co., 1986., pp. 348-362 TAKAKU A., ARRIDGE R.G.C. The effect of interfacial radial and shear stresses on fibre pull-out in composite materials, J. Phys. Part D Appl. Phys., 1973, Vol.6 ,pp. 20382047 TAN N.B., McKNIGHT S.H., Chemical segregation in epoxy precursor mixtures at simulated fiber/matrix interfaces, Polymeric materials science and engineering, Proc. American chemical Soc. 1997, Vol. 77, pp. 640-641 TANIGUSHI K., OHIRA M., ISHII M., The effect of matrix resin on the mechanical properties of fiberglass reinforced pipes for the oil and gas production, 46th Annual Conference, Composites Institute, The Society of the Plastic Industry Inc., 1991, 18-21 Février. THOMASSON J.L., Investigation of composite interphase using dynamic mechanical analysis : artifacts and reality, Polym. Compos., 1990, Vol. 11, N°2, pp. 105-113 THOMASSON J.L., The interface region in glass fibre reinforced epoxy resin : 1. Sample preparation, void content and interfacial strength, Compos., 1995, Vol. 26, N°7, pp. 467-475 THOMASSON J.L., The interface region in glass fibre-reinforced epoxy resin composites : 2. Water absorption, voids and the interface, Compos., 1995, Vol. 26, pp. 477485 217 Références bibliographiques THOMSON K.W., WONG T., BROUTMAN L.J., The plasticization of an epoxy resin by dibutylphthalate and water, Polym. Eng. Sci., 1984, Vol. 24, N°16, pp. 1270-1276 TIMM D.C., AYORINDE A.J., FORAL R.F. et al., Epoxy mechanical properties : function of crosslink architecture, Brit. Polym. J., 1985, Vol. 17, N°2, pp. 227-232 TOLF G., CLARIN P., Comparison between flexural and tensile modulus of fibre composites, Fiber. Sci. Tech., 1984, Vol. 21, pp. 319-326 TRENS P., DENOYEL R., ROUQUROL J., Adsorption of γ-APS on silica from aqueous solution : a microcalorimetric study, Langmuir, 1995, Vol. 11, pp. 551-554 TRIPATHI D., CHEN F., JONES F.R., A comprehensive model to predict the stress field in a single fibre composite, J. Compos. Mater., 1996, Vol. 30, N°14, pp. 1514-1538 TRIPATHI D., JONES F.R., Measurement of the load-bearing capability of the fibre/matrix interface by single-fiber fragmentation, Compos. Sci. Tech., 1997, Vol. 57, N°8, pp. 925-935 TRIPATHI D., JONES F.R., Review, Single fibre fragmentation test for assessing adhesion in fibre reinforced composites, J. Mater. Sci., 1998, Vol. 33, pp. 1-16 URBACZEWSKI E., Influence de la nature des prépolymères diépoxydes et des comonomères sur la réactivité et les propriétés des réseaux ; application à l’enroulement filamentaire et à la tenue en fatigue de composites unidirectionnels, Thèse de Doctorat, Institut National des Sciences Appliquées de Lyon, 1989, 317 p. VAN MELE B., VERDONCK E., Physico-chemical characterization of the fibre/matrix interaction in polyethylene fiber / epoxy matrix composites. Part 2. Characterization of the interphase with FT-IR microspectroscopy, Compos. Inter., 1995, Vol. 3, N°2, pp. 101-119 VANLANDINGHAM R., EDULJEE R.F., GILLESPIE J.W. JR, Moisture diffusion in epoxy resin, J. App. Polym. Sci., 1999, Vol. 71, pp. 787-798 VENKATAKRISNHAIAH S., DHARANI L.R., Interfacial stresses in a microbond pull-out specimen, Europ. J. Mech. A/Solids, 1994, Vol. 13, N°3, pp. 311-325 VETROTEX, Verre textile pour renforcement des matières plastiques, – Centre Européen de Recherches et d’Essais de Vetrotex St Gobain, Chambery, Les cahiers du plastique armé, N° 7714, 1978, 51 p. WAGNER H.D., GALLIS H.E., WIESEL E., Study of the interface in Kevlar 49 – epoxy composites by means of microbond and fragmentation tests : effects of materials and testing variables, J. Mater. Sci., 1993, Vol. 28, pp. 2238-2244 WAGNER H.D., LUSTIGER A., Effect of water on the mechanical adhesion of the glass / epoxy interface, Compos., 1994, Vol. 25, N°7, pp 613-616 WAGNER H.D., NAIRN J.A., DETASIS M., Toughness of interfaces from initial fiber-matrix debonding in a single fiber composite fragmentation test, Appl. Compos. Mater., 1995, Vol. 2, N°2, pp. 107-125 218 Références bibliographiques WAGNER H.D., Residual stresses in microcomposites and macrocomposites, J. Adhesion., 1995, Vol. 52, pp 131-148 WAGNER H.D., RUBINS M., MAROM G., The significance of microcomposites as experimental models, Polym. Compos., 1991, Vol. 12, N°4, pp. 233-236 WAGNER H.D., Stochastic concepts in the study of size effects in the mechanical strength of highly oriented polymeric materials, J. Polym. Sci., Polym. Phys., 1989, Vol. 27, N°1, pp. 115-149 WANG D., JONES F.R., DENISSON P., ToF SIMS and XPS study of the interaction of hydrolysed γ-APS with E-glass surfaces, J. Adh. Sci. Technol, 1992, Vol. 6, N°1, pp. 79-98 WANG D., JONES F.R., Surface analytical study of the interaction between γ-APS and E-glass surface – Part I Time-of-flight ion mass spectrometry, J. Mater. Sci, 1992, Vol. 27, pp. 36-48 WANG D., JONES F.R., Surface analytical study of the interaction between γ-APS and E-glass surface – Part II X-ray photoelectron spectroscopy, J. Mater. Sci, 1992, Vol. 27, pp. 2481-2488 WANG D., JONES F.R., ToF-SIMS and XPS Studies of the interaction of silanes and matrix resins with glass surfaces, Surf. Int. Anal., 1993, Vol. 20, pp. 457-467 WANG H.B., LI S.J., YU T.Y., On the thermal behavior and mechanism of residual microstress buildup at the matrix interface in filled epoxy resins, Polym. Eng. Sci., 1993, Vol. 33, N°8, pp. 474-479 WEIBULL W. A statistical distribution function of wide applicability, J. Appl. Mech., 1951, Vol 18, pp.293-297 WELLS J.K., BEAUMONT P.W.R., Debonding and pull-out processes in fibrous composites, J. Mater. Sci., 1985, Vol 20, pp. 1275-1284 WILLIAMS J.G., European group on fracture : Kc and Gc methods for polymers, Polymer Testing, 1990, Vol. 9, pp. 15-26 WILLIAMS J.G., Fracture Mechanics of Polymers. New York: Ellis Horwood Limited, 1984, 302 p. WILLIAMS J.G., The β relaxation in epoxy resin based networks, J. Appl. Polym. Sci., 1979, Vol. 23, pp. 3433-3444. WILLIAMS J.G., The effect of tropical weathering on glass reinforced epoxy resin, Composites, 1977, Vol. 8, N°3, pp. 157-160 WOO M., PIGGOTT M., Water absorption of resins and composites : I. Epoxy homopolymers and copolymers, J. Compos. Tech. Res., 1987, Vol. 9, N°3, pp. 101-107 WOO M., PIGGOTT M., Water absorption of resins and composites : II. Diffusion in carbon and glass reinforced epoxies, J. Compos. Tech. Res., 1987, Vol. 9, N°4, pp. 162-166 219 Références bibliographiques WOO M., PIGGOTT M., Water absorption of resins and composites : IV. Water transport in fiber reinforced plastics, J. Compos. Tech. Res., 1988, Vol. 10, N°1, pp. 20-24 WU H.F., CLAYPOOL C.M. A finite element model of the use of the microbond test method for characterization of composite interfacial properties, J. Mater. Sci. Lett., 1991, Vol 10, pp. 1072-1075 WU H.F., CLAYPOOL C.M. An analytical approach of the microbond test method used in characterizing the fibre-matrix interface, J. Mater. Sci. Lett, 1991, Vol 10, pp. 260262 XIAO G.Z., SHANAHAN M.E.R., Water absorption and desorption in an epoxy resin with degradation, J. Polym. Sci., Polym. Phys. Ed., 1997, Vol. 35, pp. 2659-2670 YAVIN B., GALLIS, H.E., SCHERF J., EITAN A., WAGNER H.D., Continous monitoring of the fragmentation phenomenon in single fiber composite materials, Polymer Compos., 1991, Vol. 12, N°6, pp. 436-446 YUE C.Y., CHEUNG W.L. Interfacial properties of fibrous composites. Part II. Determination of interfacial shear strength, interfacial coefficient of friction, and the shrinkage pressure on the fibre, J. Mater. Sci., 1992, Vol. 27, pp. 3181-3191 YUE C.Y., CHEUNG W.L., Discrimination between strentgh-based and fracturebased approaches in debonding in glass-fibre-reinforced polypropylene composite, J. Mater. Sci. Lett, 1991, Vol. 10, pp. 1335-1337 YUE C.Y., CHEUNG W.L., Interfacial properties of fibrous composites. Part I. Model for the debonding and pull-out processes, J. Mater. Sci., 1992, Vol. 27, pp. 3173-3180 ZHANDAROV S., PISANOVA E., LAUKE B., Is there any contradiction between the stress and energy failure criteri in micromechanical tests? Part I. Crack initiation: stress controlled or energy controlled?, Compos. Inter., 1998, Vol. 5, N°5, pp. 387-404 ZHOU L.M., KIM J.K., MAI Y.W. Interfacial debonding and fibre pull-out stresses. Part II. A new model based on the fracture mechanics approach, J. Mater. Sci., 1992, Vol. 27, pp. 3155-3166 ZHOU X.F., NAIRN J.A., WAGNER H.D., Fiber matrix adhesion from the single fiber composite test : nucleation of interfacial debonding, Soumis. ZINCK P., PAYS M.F., REZAKHANLOU R., GERARD J.F., Extrapolation techniques at short gauge length based on the weakest link concept for fibres exhibiting multiple failure modes, Philos. Mag. A., 1999, Vol. 79, N°9, pp. 2103-2122 220