3/2 126 SOLENOID VALVES ATEX
Transcription
3/2 126 SOLENOID VALVES ATEX
SOLENOID VALVES 2 manual reset type flameproof enclosure, II 2 GD EEx d IIC T6-T5 IP65 direct operated, poppet type 3 ports in body - 1/2 U 3/2 Series 1 3 126 ATEX FEATURES Solenoid valve with explosionproof operator type MB for use in potentially explosive atmospheres according to ATEX Directive 94/9/EC EC type examination certificate no.: LCIE 03 ATEX 6059 X Compliance with the Essential Health and Safety Requirements of the ATEX Directive has been assured by compliance with European Standards EN 50014, EN 50018, EN 50281-1-1 and EN 13463-1 Solenoid valve requiring manual resetting with coil energised after returning from the tripped state on loss of power Easy electrical connection with screw terminals Two types of seals for a wide range of applications, particularly at low temperatures The solenoid valves haveTÜV certified IEC 61508 Functional Safety data and can be used up to SIL 4/AK 7 (see Options page 2) ● ● ● ● ● ● GENERAL 0 to 10 bar [1 bar = 100 kPa] Differential pressure Response time 20 ms (on loss of voltage, with air ΔP = 6 bar) fluids (✴ ) seal materials (✴) NBR (nitrile) VMQ (silicone) temperature ranges (TS) 60°C - 10°C to + 60°C (1) - 40°C to + air, inert gas MATERIALS IN CONTACT WITH FLUID (✴ ) Ensure that the compatibility of the fluids in contact with the materials is verified Brass body Stainless steel body Body Brass AISI 316L SS Internal parts Stainless steel, brass Stainless steel Springs Stainless steel Stainless steel Seals NBR or VMQ NBR or VMQ LCIE T amb. / T cable ˚C ATEX T 0061 T ˚C YEAR SOL. TYPE Hz. MEDIUM CATALOGUE DO NOT O DELAY OP I WATTS T.P.L. SERIAL No ES FRANCE OTHER MATERIALS Solenoid operator housing Cover screw Core tube Core and plugnut Nameplate 1 Aluminium Steel Stainless steel Stainless steel Aluminium 2 3 ELECTRICAL CHARACTERISTICS Electrical safety Coil connection Standard voltages (Other voltages and 60 Hz on request) SAFETY CODE IEC 335 II 2 G EEx d IIC T6 - T5 Screw terminals II 2 D IP65 T 85°C - T 100°C DC (=) : 24V - 48V AC (~) : 24V - 115V - 230V / 50 Hz ambient temperature range/operator (TS) (W) (W) (°C) 13/18 10,4/12,5 -40 to +60 nominal power ratings hot/ hot/cold (*) cold ~ = solenoid operator reference MB - - electrical protection (EN 60529) safety code II 2GD EEx d IIC T5 spare coil ~ 230 V / 50 Hz (*) aluminium IP65 43004053 (C) = 24 V DC 43002092 1 (C)Construction type TEMPERATURE CLASSIFICATION Operator type MB, DC (=) Operator type MB, AC (~) coil size max. ambient temp.°C surface temperature Pn coil size max. ambient temp.°C surface temperature (*) AC : Rectified coil construction. Pn T6 T5 T4 T3 (Watt) 85°C 100°C 135°C 200°C insulation class H (180°C) 100 % E.D. 12,5 z 50 60 3/2 3/2 T6 T5 T4 T3 (Watt) 85°C 100°C 135°C 200°C insulation class H (180°C) 100 % E.D. 18 z 50 60 9 02 SPECIFICATIONS flow pipe orifice coefficient size size Kv 1 2 2 3 1 2 2 3 (NPT) (mm) (mm) (m3/h) (l/min) (m3/h) (l/min) operating pressure differential (bar) maximum (PS) air (✴ ) min. catalogue number solenoid operator type ~ = 0 10 10 MB 0 10 10 MB seals NBR VMQ (1) ~ = 126 00 003 126 00 004 126 00 015 126 00 016 ~ = 126 00 009 126 00 010 126 00 021 126 00 022 U - universal operation, brass body 1/2 10 10 2,1 35 2,1 35 U - universal operation, stainless steel body 1/2 (1) 10 10 2,1 35 2,1 35 Low temperature version: allowable temperatures: fluid -40°C to +60°C; minimum ambient: -40°C. Consult us for -50°C. All leaflets are available on:www.ascojoucomatic.com V902-52-GB-R8 SOLENOID VALVES - SERIES 126 OPTIONS ● ● ● ● ● ATEX cable gland certified to EEx d, 3/4 NPT, pre-installed on solenoid valve, supplied with cable clamp (see V1090) - for non-armoured cable of 8.5 to 16 mm dia., catalogue number 660 510 - for armoured cable of ID 8.5 to 16 mm / OD 12 to 21 mm, catalogue number 660 514 SIL certification (including NPT 1/2 stainless steel exhaust protector), catalogue number 610 544 For other cable diameters, consult us Exhaust protector: bronze for brass valve, catalogue number 560 595; stainless for stainless steel valve, catalogue number 560 594 Marine paint/anti-corrosive or dust environments INSTALLATION ● ● Always install solenoid valve with body vertical and solenoid upward Universal type solenoid valves of series 126 can be used for the following functions, depending on how the ports are connected: 2/2 NC 2/2 NO 2 3 ● ● ● ● ● ● 3/2 NC 3 1 3/2 NO 2 2 3 1 Mixing 2 1 3 Selector 2 3 1 2 1 3 1 These solenoid valves have 3 mounting holes IEC 61508 Functional Safety, allowable temperature range: -40°C to +60°C. Probability of failure on demand, consult ASCO/JOUCOMATIC Threaded pipe connection is standard NPT (ANSI 1.20.3) Valves (catalogue number 610 544) should be provided with a specific exhaust protector Installation/maintenance instructions are included with each valve Spare part kits and replacement coils are available DIMENSIONS (mm), WEIGHT (kg) TYPE 01 Solenoid operator type "MB" Aluminium EN50018 II 2 GD EEx d IIC 94 + 18 94 1 18,5 32 50 56 H G 57 360˚ 2 1 2 = 32 30 = = = 1 3 3 x 1/2 NPT 3 3 x Ø6,6 40 Ø39 = 40 = solenoid operator type MB = weight (1) 2,5 (brass) 2,1 (S.S.) (1) including coil. = = 62 3 = 1 Dimension to be added to allow for removal 2 Explosionproof cable gland to ATEX with clamp 3 Manual reset 4 To change the orientation of the solenoid operator relative to the ports, the screw (H) and the nut of the cover (G) must be loosened All leaflets are available on:www.ascojoucomatic.com V902-52-2 ASCO/JOUCOMATIC reserves the right to alter the availability, design and specifications without notice. 1 3/4 NPT 214 + 100 132,5 + 100 1 6