Transcription
pdf
SikaMur ®-InjectoCream-100 3. Injection Required numbers of Sausages / Cartridges Length of the wall Wall thickness 110 mm 220 mm 330 mm 440 mm 10 m 1.5 /3.0 3.0 /6.0 5.1 /10.2 7.0 /14.0 20 m 3.0 /6.0 6.0 /12.0 10.2 /20.4 13.0 /26.0 30 m 4.6 /9.2 9.0 /18.0 15.3 /30.6 21.0 /42.0 40 m 6.1 /12.2 12.0 /24.0 20.4 /40.8 28.0 /56.0 Know-how from Site to Shelf SikaMur ®InjectoCream-100 Horizontal damp proof course for rising damp treatment Insert the delivery tube into the full depth of the pre-drilled hole. Backfill each hole fully with SikaMur®InjectoCream-100 to within 1 cm of the surface. For the required numbers of cartridges for your application please refer to the table above. Plug or fill drilled holes with a suitable Sika Mortar. After Treatment The Insertion of chemical damp-proof course does not immediately dry out damp walls; it only controls the further vertical migration of moisture from the ground. Therefore, if possible delay the ancillary and additional works for as long as it is practically possible to facilitate the maximum period of drying. How to ensure long lasting good result: Sika – Specialised Trade Partner 1. Provide good ventilation to allow drying of the wall. 3. Replaster using the SikaMur® drying plaster. 4. Fill externally drilled holes with suitable mortar e.g. Sika® MiniPack repairing mortar. 5. It is recommended to cover outside part of wall with Sikagard®-703 W water-reppelent impregnation for walls and facades. All orders are accepted subject to our current terms of sale and delivery. Users should always refer to the most recent issue of the Product Data Sheet for the product concerned. Sika Services AG Business Unit Distribution CH-8048 Zürich Switzerland Phone +41 58 436 40 40 Fax +41 58 436 46 86 www.sika.com © Sika Services AG / BUD / 06.11 / CMS 2. Ensure that the damp-proof membrane of any new solid floor overlaps with the inserted dampproof course. If no DMP is present, apply 2 coats of Sika® MiniPack waterproofing slurry across the solid floor for 50 – 100 mm and up the wall to overlap with the DPC. SikaMur ®-InjectoCream-100 SikaMur®-InjectoCream-100 Silane-based injectable damp proof course for rising damp treatment How to use it 1. Wall Preparation Blistered paint work, peeled wallpaper, dry rot, timber decay, and bad “musty” smell – not really an environment of enjoyable living. This is the case thogh in many (old) buildings and the cause is rising Damp. Before treatment After treatment Remove skirting boards and/ or plaster/ render to expose the masonry to be treated. Measure thickness of the wall. If the plaster/ render is polluted with salts or has been damaged, it must be completely removed. Drill holes with a diameter of 12 mm at the junction of the vertical and horizontal mortar courses, not further than 120 mm apart. The depth of the holes required for various wall thicknesses is showing the Table below. After the drilling operation, each individual hole needs to be thoroughly cleaned using a manual air pump. Required depth of the holes for different wall thicknesses Sikamur®-InjectoCream-100 is a water repellent cream, it is inserted into a series of holes drilled into a mortar course of the masonry using a simple application gun. No special injection pump is required! Once injected to the mortar course, Sikamur®-InjectoCream-100 will diffuse within the damp wall to form a water repellent barrier and block future rising damp. Box with 12 Cartridges + 3 extension tubes/box Shelf life: 12 month SikaMur -InjectoCream-100 is: ® Economic and effective n Consistent application rate (easy to calculate the amount of required material) n Concentrated formula with more than 80% active ingredients n Very low wastage Easy to apply 110 mm 220 mm 330 mm 440 mm Depth of hole required 100 mm 190 mm 310 mm 420 mm Saving time Drilling Paterns n Fast to install (no ‘double drilling’, no waiting for liquid to penetrate). n Fast to inject (no waiting times required to pump in the material compared to pressure injection systems) Stretching Bond Double flemish Bond Random 150 mm above ground level 150 mm above ground level 150 mm above ground level Safe application n 1-component, ready to use n Simple application by gun, does not require a special pump n No risk of increased efflorescence (as with siliconate rising damp treatments). For all types of masonry walls Box with 10 Sausages Shelf life: 12 month Wall thickness n Can be used to treat rising damp in almost all types of masonry walls n Solid brick walls n Cavity walls n Random form stone and rubble infill walls, etc. n Low hazard, water based – noncaustic, nonfl ammable – not injected under pressure. n Spillage & mess virtually eliminated from the site (no problem with fluids flooding through party walls, cavities or service ducts). 2. Sausage /Cartridge Preparation Left, Sausage: Insert SikaMur®InjectoCream-100 into the gun. Cartridges: Insert it into the gun, puncture the breech and place the application nozzle at the end of the gun. Right, Sausage: Cut or puncture the visible end of the sausage. Cartridges: Place the delivery tube on the special graduated Nozzle.