PC-Interface USB/SPI
Transcription
PC-Interface USB/SPI
JUMO PC-Interface USB/SPI B 709720.5 Betriebsanleitung Operating manual Notice de mise en service 2011-05-20/00553148 JUMO PC-Interface mit USB/SPIUmsetzer und Adapter (Buchse) B 709720.5 Betriebsanleitung 2011-05-20 1 Kurzanleitung 1.1 Sicherheitshinweise Allgemein Lesen Sie diese Anleitung, bevor Sie das Gerät in Betrieb nehmen. Bewahren Sie die Anleitung an einem für alle Benutzer jederzeit zugänglichen Platz auf. Sollten bei der Inbetriebnahme Schwierigkeiten auftreten, bitten wir Sie, keine Manipulationen vorzunehmen, die Ihren Gewährleistungsanspruch gefährden können! Bestimmungsgemäße Verwendung Das PC-Interface mit USB/SPI-Umsetzer ist für die Konfiguration oder den Abgleich von Messumformern des Typs 70703x geeignet. Das Interface ist lediglich für eine zeitlich begrenzte Schnittstellenverbindung konzipiert. Bitte darauf achten, dass nach dem Setup-Datentransfer die Schnittstellenverbindung wieder getrennt wird. Lieferumfang • 1 PC-Interface mit USB/SPI-Umsetzer • 1 USB-Kabel (grau) • 1 Verbindungskabel Umsetzer/Messumformer (grau) • 1 Adapter (Buchse) • 1 Mini-CD mit USB-Treiber • 1 Betriebsanleitung B 709720.5 3 1 Kurzanleitung 1.2 Treiberinstallation Schritt Tätigkeit 1 Laptop oder PC einschalten 2 Mini-CD (1) in das CD-Laufwerk einlegen ➥ Das Installationsprogramm startet mit der Sprachauswahl. 3 Sollte der Autostart nicht funktionieren, die Datei launch.exe auf der Mini-CD starten ➥ Das Installationsprogramm startet mit der Sprachauswahl. 4 Sprache des Installationsprogramms auswählen 5 Treiber anklicken ➥ Der Treiber wird automatisch installiert. 4 1 Kurzanleitung Schritt Tätigkeit 6 USB-Kabel (2) in die Buchse des Laptop/PC stecken ➥ Das Betriebssystem meldet die neu erkannte Hardware. 7 Gerät über den Adapter (3) mit dem Interface verbinden ➥ Jetzt kann der Anwender über das Setup-Programm eine Verbindung zum Gerät herstellen. � � � HINWEIS! Zur Konfiguration muss der Messumformer mit Spannung versorgt werden. Steht kein Netzgerät (Speisetrenner) zur Verfügung, kann der Messumformer zur Konfiguration mit Hilfe einer 9V-Blockbatterie versorgt werden. Die Setup-Schnittstelle darf nur kurzzeitig (zur Konfiguration) verwendet werden. Ein Dauerbetrieb ist nicht gestattet. 5 1 Kurzanleitung 1.3 • • CD-ROM Laufwerk freie USB-Schnittstelle 1.4 • Hardware-Voraussetzungen Software-Voraussetzungen Microsoft Windows 2000, XP, Vista oder Windows 7 (32 Bit und 64 Bit)1 1.5 Technische Daten Spannungsversorgung Leistungsaufnahme Galvanische Trennung Umwelteinflüsse Umgebungstemperaturbereich Lagertemperaturbereich Klimafestigkeit Elektromagnetische Verträglichkeit Störaussendung Störfestigkeit Gewicht USB/SPI-Umsetzer Kabel Gehäuse Material Farbe 1 6 DC 5 V (USB Bus powered) < 0,5 W DC 50 V 0 ... 50 °C -20 ... +70 °C 93 % rF ohne Betauung EN 55022, Klasse B EN 55024 ca. 55 g ca. 100 g Polycarbonat RAL 7001, Silbergrau Microsoft und Windows sind eingetragene Warenzeichen der Microsoft Corporation JUMO GmbH & Co. KG Moritz-Juchheim-Straße 1 36039 Fulda, Germany Telefon: Telefax: E-Mail: Internet: +49 661 6003-727 +49 661 6003-508 [email protected] www.jumo.net Technischer Support Deutschland: Telefon: Telefax: E-Mail: +49 661 6003-300 oder -653 oder -899 +49 661 6003-881729 [email protected] Lieferadresse: Mackenrodtstraße 14 36039 Fulda, Germany Postadresse: 36035 Fulda, Germany JUMO Mess- und Regelgeräte Ges.m.b.H Pfarrgasse 48 1232 Wien, Austria Telefon: Telefax: E-Mail: Internet: +43 1 610610 +43 1 6106140 [email protected] www.jumo.at Technischer Support Österreich: Telefon: Telefax: E-Mail: +43 1 610610 +43 1 6106140 [email protected] JUMO Mess- und Regeltechnik AG Laubisrütistrasse 70 8712 Stäfa, Switzerland Telefon: Telefax: E-Mail: Internet: +41 44 928 24 44 +41 44 928 24 48 [email protected] www.jumo.ch Technischer Support Schweiz: Telefon: Telefax: E-Mail: +41 44 928 24 44 +41 44 928 24 48 [email protected] JUMO PC interface with USB/SPI converter and adapter (socket) B 709720.5 Operating Manual 2011-05-20 1 Brief instructions 1.1 Safety information General information Please read this manual before commissioning the device. Keep the manual in a place accessible to all users at all times. If difficulties occur during commissioning, please refrain from carrying out any manipulations that could jeopardize your warranty rights. Intended Use The PC interface with USB/SPI converter is suitable for the configuration or the calibration of transmitter, type 70703x. The interface is only designed for a time-limited interface connection. Please ensure that the interface connection is disconnected after the setup data transfer. scope of delivery • 1 PC interface with USB/SPI converter • 1 USB cable (gray) • 1 Connection cable, converter/transmitter (gray) • 1 Adapter (socket) • 1 Mini-CD with USB driver • 1 Operating manual B 709720.5 3 1 Brief instructions 1.2 Driver installation Step Activity 1 Switch on the laptop or PC 2 Insert the Mini-CD (1) into the CD drive ➥ The installation program starts with the language selection. 3 If installation is not started automatically, start the launch.exe file on the Mini-CD. ➥ The installation program starts with the language selection. 4 Select the language for the installation program 5 Click on the driver ➥ The driver is automatically installed. 4 1 Brief instructions Step Activity 6 Connect the USB cable (2) to the laptop/PC socket ➥ The operating system indicates the new hardware detected. 7 Connect the device to the interface via the adapter (3) ➥ Now the user can establish a connection to the device using the setup program. � � � TIP! For configuration, ensure that voltage is supplied to the transmitter. If no power pack (isolating amplifier) is available, the transmitter can be supplied for configuration by means of a 9V monobloc battery. Only use the setup interface for a short period (for configuration). Permanent operation is not permitted. 5 1 Brief instructions 1.3 • • CD-ROM drive free USB interface 1.4 • Required hardware Required software: Microsoft Windows 2000, XP, Vista or Windows 7 (32 Bit and 64 Bit)1 1.5 Technical data Voltage supply Power consumption Electrical isolation Environmental influences Ambient temperature range Storage temperature range Environmental performance Electromagnetic compatibility emitted interference interference resistance Weight USB/SPI converter Cable Case Material Color 1 6 DC 5 V (USB Bus powered) < 0.5 W DC 50 V 0 ... 50 °C -20 ... +70 °C 93 % rel.hum. without condensation EN 55022, class B EN 55024 approx. 55 g approx. 100 g Polycarbonate RAL 7001, silver gray Microsoft and Windows are registered trademarks of Microsoft Corporation. JUMO GmbH & Co. KG Street address: Moritz-Juchheim-Straße 1 36039 Fulda, Germany Delivery address: Mackenrodtstraße 14 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: [email protected] Internet: www.jumo.net JUMO Instrument Co. Ltd. JUMO House Temple Bank, Riverway Harlow, Essex CM20 2DY, UK Phone: +44 1279 635533 Fax: +44 1279 635262 e-mail: [email protected] Internet: www.jumo.co.uk JUMO Process Control, Inc. 8 Technology Boulevard Canastota, NY 13032, USA Phone: 315-697-JUMO 1-800-554-JUMO Fax: 315-697-5867 e-mail: [email protected] Internet: www.jumo.us JUMO Interface pour PC avec convertisseur USB/SPI et adaptateur (connecteur femelle) B 709720.5 Notice de mise en service 2011-05-20 1 Notice succinte 1.1 Instructions de sécurité Généralités Lisez cette notice avant de mettre en service l’appareil. Conservez-la dans un endroit accessible à tout moment par l’ensemble des utilisateurs. Si vous rencontrez des difficultés lors de la mise en service, ne procédez à aucune manipulation qui pourrait compromettre votre droit à la garantie ! Utilisation conforme aux prescriptions L'interface pour PC avec convertisseur USB/SPI est adapté à la configuration ou à l'étalonnage de convertisseurs de mesure, type 70703x. L'interface est seulement conçue pour une connexion limitée dans le temps. Veillez à ce que la connexion soit à nouveau coupée après le transfert de données - Setup. Contenu de la livraison • 1 interface pour PC avec convertisseur USB/SPI • 1 câble USB (gris) • 1 câble de connexion convertisseur/convertisseur de mesure (gris) • 1 adaptateur (connecteur femelle) • 1 mini-CD avec driver USB • 1 notice de mise en service B 709720.5 3 1 Notice succinte 1.2 Installation du driver Etape Action 1 Brancher le PC portable ou le PC 2 Insérer le mini-CD (1) dans le lecteur de CD ➥ Le programme d'installation démarre avec le choix de la langue. 3 Si le démarrage automatique ne fonctionne pas, lancer le fichier launch.exe qui se trouve sur le mini-CD ➥ Le programme d'installation démarre avec le choix de la langue. 4 Sélectionner la langue du programme d'installation 5 Cliquer sur driver ➥ Le driver est installé automatiquement. 4 1 Notice succinte Etape Action 6 Brancher le câble USB (2) dans le connecteur femelle du PC portable/PC ➥ Le système d'exploitation signale le matériel détecté. 7 Connecter l'appareil via l'adaptateur (3) avec l'interface ➥ L'utilisateur peut établir une connexion via le logiciel Setup. � � � REMARQUE ! Pour la configuration, le convertisseur de mesure doit être mis sous tension. S'il n'y a pas d'alimentation (alimentation à séparation galvanique) à disposition, le convertisseur de mesure peut être alimenté avec une pile 9 V. L'interface Setup ne peut être utilisée que brièvement (pour la configuration). Un fonctionnement continu n'est pas autorisé. 5 1 Notice succinte 1.3 • • Lecteur de CD-ROM Port USB libre 1.4 • Conditions matérielles Conditions logicielles Microsoft Windows 2000, XP, Vista ou Windows 7 (32 Bit et 64 Bit)1 1.5 Caractéristiques techniques Alimentation Consommation Séparation galvanique Influences de l’environnement Plage de la température ambiante Plage de la température de stockage Résistance climatique Compatibilité électromagnétique Emission de parasites Résistance aux parasites Poids Convertisseur USB/SPI Câble Boîtier Matériau Couleur 1 6 DC 5 V (USB Bus powered) < 0,5 W DC 50 V 0 à 50 °C -20 à +70 °C 93 % Hr sans condensation EN 55022, classe B EN 55024 env. 55 g env. 100 g Polycarbonate RAL 7001, gris argent Microsoft et Windows sont des marques déposées de Microsoft Corporation. JUMO GmbH & Co. KG Adresse : Moritz-Juchheim-Straße 1 36039 Fulda, Allemagne Adresse de livraison : Mackenrodtstraße 14 36039 Fulda, Allemagne Adresse postale : 36035 Fulda, Allemagne Téléphone : +49 661 6003-0 Télécopieur : +49 661 6003-607 E-Mail: [email protected] Internet: www.jumo.net JUMO Mess- und Regeltechnik AG Laubisrütistrasse 70 8712 Stäfa, Switzerland Telefon: +41 44 928 24 44 Telefax: +41 44 928 24 48 E-Mail: [email protected] Internet: www.jumo.ch JUMO Régulation SAS Actipôle Borny 7 Rue des Drapiers B.P. 45200 57075 Metz - Cedex 3, France Téléphone : +33 3 87 37 53 00 Télécopieur : +33 3 87 37 89 00 E-Mail : [email protected] www.jumo.fr Internet : Service de soutien à la vente : 0892 700 733 (0,337 Euro/min) JUMO Automation S.P.R.L. / P.G.M.B.H. / B.V.B.A. Industriestraße 18 4700 Eupen, Belgique Téléphone : +32 87 59 53 00 Télécopieur : +32 87 74 02 03 E-Mail : [email protected] Internet : www.jumo.be