Black Jack DataSheets
Transcription
Black Jack DataSheets
9802F MS-400 BUILDING TAPE Data Sheet TYPICAL PHYSICAL & PERFORMANCE CHARACTERISTICS Seals Doors, Windows, Skylights, Flashings • • • • SBS rubberized flashing Suitable for low temperature application Maximum adhesion to prepared surfaces Blocks air, vapour & water Weight 5 lbs. Tensile Strength (Product) > 350 psi Elongation (Product) > 900% Tensile Strength (Film) > 2000 psi Elongation (Film) > 700% Thickness 35 mils (0.9 mm) Coverage 25 ft2 15.24cm x 15.2m Top Surface Grey Polypropylene Film Ideal for exterior use to seal around windows, doors and skylights. Prevents water and moisture from penetrating. Bottom Surface Siliconized Release FOR USE ON: Black Jack® MS-400 Building Tape is a highly modified SBS rubberized peel and stick flashing membrane which is laminated to a highly engineered plastic film, offering protection against water, air and moisture infiltration. Color Grey PREPARATION: Substrate should be clean, dry and free of dew, frost, oil, salt, dust and rust. Clean area first with a cloth and cleaner. MS-400 Building Tape can be used without primer on dry and clean substrates when temperatures are above 12,8°C (55°F). For applications below 12,8°C (55°F) prime substrate with MS-200 or MS-201 Bonding Agent. Approx. Shipping Weights: (Note: All approx. weights include container.) 6” x 50’ (15.24 cm x 15.2 m) 6 rolls to 1 carton box 30 lbs. APPLICATION: Remove release film. Press in place using a gloved hand or a steel roller. Apply the exact length to predetermined location. Tape cannot be peeled up and reset. Always roll from the center out to remove trapped air pockets and fishmouths. Start in corners to eliminate “tenting”. PRECAUTIONS: Protective clothing and eyewear should be used during application of this product. Black Jack® MS-400 Building Tape will not adhere to silicone surfaces. For best results, test adhesion on membranes before applying. Do NOT store at temperatures above 43°C (110°F). Do NOT stretch tape during installation. Do NOT use where acidic or alkaline chemicals are present (for example: lab fume hoods, vents, etc). Protect from freezing. Do not use in drinking water or food systems. CAUTION IRRITANT MAY IRRITATE SKIN. Do not get on skin. Keep out of reach of children. FIRST AID TREATMENT: Contains asphalt, petroleum oil, calcium carbonate, fiber glass. If on skin, rinse well with water. This product is asbestos free. WARRANTY & DISCLAIMER: For limited warranty and disclaimer information visit: www.gardner-gibson.com. ©2013 Gardner-Gibson, Inc. In US Distributed by: Gardner-Gibson, Inc. P.O. Box 5449, Tampa, FL 33675 In Canada Distributed by: GH International 2540 Rena Road, Mississauga, Ontario L4T 3C9 See MSDS for more info Gardner-Gibson, Inc. • P.O. Box 5449 • Tampa, Florida 33675-5449 Phone: (813) 248-2101 • Fax (813) 248-6768 • www.gardner-gibson.com D-13 9802F MS-400 RUBAN DE CONSTRUCTION Fiche Technique CARACTÉRISTIQUES PHYSIQUES TYPIQUES ET DE PERFORMANCE Poids Kg (lbs) Pour sceller portes, fenêtres, puits de lumière et solins • Bande d’étanchéité caoutchoutée SBS • Idéal pour une application à basse température • Adhérence optimale aux surfaces préparées • Bloque l’air, la vapeur et l’eau 2,27 Kg (5 lbs) Résistance à la rupture (Produit) > 350 psi Élongation (Produit) > 900% Résistance à la rupture (Film) > 2000 psi Élongation (Film) > 700% Épaisseur 35 mils (0,9mm) Couverture 25 pi2 15.24cm x 15.2m Surface Supérieure Film en Polypropylène Gris Idéal pour un usage extérieur autour des fenêtres, portes et puits de lumière. Empêche l’eau et l’humidité de pénétrer. Surface Inférieure Siliconée S’UTILISE SUR : Solins, rebords et appuis de fenêtres, puits de lumière, solins muraux, joints de revêtement primaire, gouttières, solives. Couleur Gris ADHÈRE AUX MATÉRIAUX SUIVANTS : Blocs de béton, acier apprêté, placoplâtre, contreplaqué, métal galvanisé. Poids de livraison approximatives (Note: Tous les poids incluent le poids du contenant) 6’’ x 50’ (15,24 cm x 15,2m) 6 Rouleaux par carton Jack® MS-400 est une DESCRIPTION : Le Ruban de construction Black membrane d’étanchéité caoutchoutée autoadhésive, hautement modifiée SBS, surfacée par une pellicule plastique hautes performances, qui protège contre l’infiltration d’eau, d’air et d’humidité. PRÉPARATION : Le substrat doit être propre, sec et exempt de rosée, givre, huile, sel, poussière et rouille. Nettoyer d’abord la surface avec un chiffon et un nettoyant. Le Ruban de construction MS-400 peut être utilisé sans apprêt sur une surface propre et sèche lorsque la température est supérieure à 12,8 °C (55 °F). Si la température est inférieure à 12,8 °C (55 °F), apprêter d’abord la surface au moyen de l’Agent de liaison MS-200 ou MS-201. APPLICATION : Enlever la pellicule résiduelle. Poser le ruban et bien le coller en appuyant d’une main gantée, ou à l’aide d’un rouleau en acier. Appliquer une bande d’une longueur correspondant exactement à l’emplacement déterminé. Une fois collé, le ruban ne pourra pas être décollé et déplacé. Toujours aplanir à partir du centre vers les bords afin d’éliminer les poches d’air et les bâillements. Commencer dans les coins afin d’éliminer les « soulèvements en tente ». PRÉCAUTIONS : Porter des vêtements et lunettes de protection pendant l’application de ce produit. Le Ruban de construction Black Jack® MS-400 n’adhèrera pas aux surfaces en silicone. Pour des résultats optimums, vérifier l’adhérence sur la membrane avant d’appliquer. NE PAS ranger à une température de plus de 43 °C (110 °F). NE PAS étirer le ruban pendant la pose. NE PAS utiliser là où des produits chimiques acides ou alcalins sont présents (par exemple : évents, hottes de laboratoire, etc.). Craint le gel. Ne pas utiliser dans des systèmes d’approvisionnement en eau potable ou des systèmes alimentaires. 13,61 Kg (30lbs) ATTENTION IRRITANT PEUT IRRITER LA PEAU. Éviter tout contact avec la peau. Tenir hors de la portée des enfants. PREMIERS SOINS: Contient: asphalte, huile de pétrole, carbonate de calcium, fibre de verre. En cas de contact avec la peau, bien rincer avec de l’eau. Ce produit ne contient pas d’amiante. GARANTIE ET CLAUSE D’EXONÉRATION : Pour obtenir une garantie limitée et une clause d’exonération, visitez le site: www.gardner-gibson.com. ©2013 GH International Au US Distribué par : Gardner-Gibson, Inc. P.O. Box 5449, Tampa, FL 33675 Au Canada Distribué par : GH International 2540 Rena Road, Mississauga, Ontario L4T 3C9 Fabriqué aux É.-U. Voir la fiche signalétique pour plus d’information. Fabriqué aux É.-U. Gardner-Gibson, Inc. • P.O. Box 5449 • Tampa, Florida 33675-5449 Phone: (813) 248-2101 • Fax (813) 248-6768 • www.gardner-gibson.com D-13