Küvetten-Test LCK 514 CSB
Transcription
Küvetten-Test LCK 514 CSB
PA 514 - 06/7 Küvetten-Test LCK 514 Programmieranleitung CADAS 100 LPG ≥ 210 CSB Ausgabe 97/06 Achtung! Das Ausgabedatum dieser Programmieranleitung muß mit dem Ausgabedatum der Arbeitsvorschrift der Reagenzien identisch sein. Nur so ist gewährleistet, daß Sie die korrekten Daten in Ihr Gerät einprogrammieren. Hinweis! Sollten Sie während der Programmierung einen Fehler machen, können Sie die letzte Eingabe durch Drücken der Taste ➞ auf der Tastatur rückgängig machen. bezeichnen die rechte und linke ➞ und L ➞ ➞ Die Eingabezeichen R Taste. Programmierung von LCK 514 CSB ● Programm PRG (Programmierung eines Testes) anwählen CSB Display-Anzeige Eingabe Programmnummer: z. B. 1 ➞ Symbol: L Name: CSB Pro: 1 W: λ = Faktor: 1 = 2 3 STA FPRG ... nm 514 Taste unter 1 anwählen 605 2046 Einheit: mg L Meßbereichsgrenzen: ja nein / X ➞ -37.39 ➞ Konstante: R l Taste unter ja anwählen untere Grenze: 100 obere Grenze: 2000 Programmierung von LCK 514 CSB ● Programm VAR (Variation eines Testes anwählen - sollte dieser Test auf Ihrem Gerät bereits abgelegt sein). ● Taste unter Symbol »514« anwählen. CSB Display-Anzeige Eingabe Programmnummer: z. B. 1 Symbol: 514 Name: CSB Pro: 1 3 STA FPRG Taste unter 1 anwählen λ = 605 nm W: Faktor: 2 1 = 2046 Konstante: -37.39 Einheit: mg/l Meßbereichsgrenzen: ja untere Grenze: 100 mg/l obere Grenze: 2000 mg/l nein Taste unter ja anwählen Die komplette Dateneingabe wird auf dem Drucker dokumentiert. Die vollständige Übernahme in den Speicher wird durch den Ausdruck »gespeichert« bestätigt. Bitte vergleichen Sie den Ausdruck nochmals mit den einzugebenden Daten. PA 514 - 06/7 Programming instructions CADAS 100 LPG ≥ 210 Cuvette-Test LCK 514 COD Edition 97/06 Attention! The edition date of this programming instruction must be identical to the edition date of the intruction attached to the reagents. This is the only way to ensure that your instrument will be programmed with the correct data. Please note! If you make an error during programming, you can cancel the last entry by pressing the key ➞ on the keyboard. indicate the right and left ➞ and L ➞ ➞ The input symbols R keys respectively. Programming of LCK 514 COD P Select the program PRG (programming of a test) COD Display Input via keyboard Program number: for example 1 ➞ Symbol: L Name: COD Pro: 1 W: λ = Factor: 1 = 2 3 STA FPRG nm 514 Press the function key below 1 605 2046 Unit: mg L Measuring limit: yes no / X ➞ -37.39 ➞ Constant: R l Press function key below yes Lower limit: 100 Upper limit: 2000 Programming of LCK 514 COD P Select the program VAR (variation of a test, if this test is already stored). ● Select function key below symbol »514«. COD Display Input via keyboard Program number: for example 1 Symbol: 514 Name: COD Pro: 1 3 STA FPRG Press function key below 1 λ = 605 nm W: Factor: 2 1 = 2046 Constant: -37.39 Unit: mg/l Measuring limit: yes Lower limit: 100 mg/l Upper limit: 2000 mg/l no Press function key below yes All data entries are documented on the printer; their transfer to storage is confirmed by the printer message »stored«. You should check the printed data to ensure that all entries are correct. PA 514 - 06/7 Instruction de programmation CADAS 100 LPG ≥ 210 Test en Cuve LCK 514 DCO Edition 97/06 Attention! La date d’édition de ces instructions doit être identique à celle du mode d’emploi des réactifs. Dans ce cas seulement, vous êtes assurés d’entrer les bonnes données dans votre appareil. Conseil! En cas d’erreur durant la programmation, vous pouvez revenir sur la dernière entrée en utilisant la touche ➞ sur le clavier. servent de touche droite et gauche ➞ et L ➞ ➞ Les touches d’édition R . Programmation du LCK 514 DCO P Sélectionner le programme PRG (pour programmer un test). DCO Display Commande sur le clavier Numéro de programme: par example 1 ➞ Symbole: L Nom: DCO Pro: 1 λ = Facteur: 1 = W: 2 3 STA PRGL nm 514 Appuyer la touche sous 1 605 2046 Unité: mg L Limites de mesure: oui non / X ➞ -37.39 ➞ Constante: R l Appuyer la touche sous oui Limite inférieure: 100 Limite supérieure: 2000 Programmation du LCK 514 DCO P Sélectionner le programme VAR (pour modifier un test, dans le cas ou le test serait encore memorisé dans votre appareil). ● Choisir le symbole »514«. DCO Display Commande sur le clavier Numéro de programme: par example 1 Symbole: 514 Nom: DCO Pro: 1 W: λ = 605 nm Facteur: 1 2 = 3 STA PRGL Appuyer la touche sous 1 2046 Constante: -37.39 Unité: mg/l Limites de mesure: oui non Limite inférieure: 100 mg/l Limite supérieure: 2000 mg/l Appuyer la touche sous oui L’ensemble des données est imprimé. Le transfert complet des données dans la mémoire est confirmé par le message »mémorisé«. Vérifiez que les données imprimées corresspondent bien à celles que vous avez entrées.