Série 881 TEMPORISATEUR ELECTRONIQUE
Transcription
Série 881 TEMPORISATEUR ELECTRONIQUE
TEMPORISATEUR ELECTRONIQUE Série 881 GENERATEUR D’IMPULSIONS REGLABLES adaptable sur électrovanne PRINCIPE DE FONCTIONNEMENT Transforme une mise sous tension permanente en une succession d’impulsions de temporisation «ON» réglable de 2 à 40 sec, avec temps de repos «OFF» réglable de 0,5 à 45 min. Mise sous tension d’entrée 1 0 1 Mise sous tension de l’électrovanne 0 ON OFF ON : réglable de 2 à 40 sec. OFF : réglable de 0,5 à 45 min. APPLICATIONS Le temporisateur électronique, générateur d’impulsions réglables, est adapté à la commande automatique de : • Purge de sécheur d’air ou de compresseur ; en effet, dès sa mise sous tension, il déclenche le fonctionnement d’une électrovanne pendant le temps nécessaire à la vidange des condensats et ce, à intervalles réguliers, réglables. • Cycles d’arrosage ou de soufflage • Toutes applications avec séquences répétitives basées sur le temps SPECIFICATIONS TENSION D’ALIMENTATION INTENSITE MAXI COURANT D’APPEL MAXI CONSOMMATION TEMPERATURE AMBIANTE DEGRE DE PROTECTION AGREMENT REPETABILITE PRECISION D’ECHELLE CONNEXION ELECTRIQUE : : : : : : : : : : 24V à 240V CC/CA (50/60 Hz) 1A 10 A pendant 10 ms 4 mA maxi –10°C à +50°C IP 65 CSA ± 0,1% ± 10% Ce composant s’adapte directement sur toute électrovanne équipée de bobine à broches à raccordement normalisé ISO 4400/DIN. Il se place entre la bobine et le connecteur d’alimentation (connecteur ISO 4400, non fourni) SELECTION DU MATERIEL CODE DESIGNATION Temporisateur électronique avec commande manuelle auxiliaire pour électrovanne avec bobine à broches ISO 4400 Temporisateur orientable à 180° ENCOMBREMENTS ET MASSE Masse : 0,054 kg. 35* Electrovanne avec bobine à broches normalisées ISO 4400 OFF 16 24 10 20 30 8 32 5 40 40 0,5 45 2 ON:SEC. OFF:MIN. Voyant électrovanne hors tension 74 TEST ON 90 52 Voyant électrovanne sous tension Réglage du temps de mise sous tension 20 Joint d’étancheité 43 Poussoir «test» 88122627 Réglage du temps d’arrêt Connecteur ISO 4400 orientable de 90° en 90° CM 10 (Pg 11 P) (non fourni) * +15 mm pour déplacement du connecteur • Si la largeur du corps d’électrovanne le permet, le temporisateur peut être orienté à 180° par rapport à l’axe de connexion. • Respecter le montage du joint d’étanchéité entre bobine et temporisateur et joint du connecteur. • Le temporisateur électronique est livré avec 3 vis de longueurs différentes, pour assurer le maintien du connecteur et du temporisateur sur l’électrovanne. Le choix, entre ces 3 vis, s’effectue en fonction de la hauteur du connecteur utilisé. • Réglage en intervenant sur les boutons ON et OFF • Le poussoir «TEST» permet de mettre l’électrovanne sous tension, lorsque la tension d’alimentation d’entrée est présente. IM-1145-X-R0 3834493 MISE EN SERVICE - MONTAGE - REGLAGE ELECTRONIC MULTITIMER Series 881 WITH ADJUSTABLE PULSES adaptable on solenoid valve WORKING PRINCIPLE Converts a continuous duty cycle into a sequence of «ON» timing pulses, adjustable from 2» to 40», with an «OFF» dead time, adjustable from 0.5 min. to 45 min. 1 Input supply 0 1 Duty cycle of the solenoid valve 0 ON ON : adjustable from 2 to 40 seconds OFF : adjustable from 0.5 to 45 minutes OFF APPLICATIONS This electronic timer, which generates adjustable pulses, is suitable for automatic control of : • Air drives and compressors where it can open solenoid valves for the time required to discharge condensates at regular and adjustable intervals. • Irrigation and air-blast cycles. • All applications requiring regular sequential operation. SPECIFICATIONS VOLTAGE MAX. INTENSITY MAX. INRUSH CURRENT CONSUMPTION AMBIENT TEMPERATURE PROTECTION CLASS CERTIFICATION REPEATABILITY SCALE ACCURACY CONNECTION : : : : : : : : : : 24V to 240V DC/AC (50/60 Hz) 1A 10 A for 10 ms 4 mA max. –10°C to +50°C IP 65 CSA ± 0,1% ± 10% This component can be mounted on any solenoid valve equipped with a coil with spade terminals to ISO 4400/DIN. It is placed between the coil and the power connector (connector to ISO 4400, not supplied). RANGE SPECIFICATIONS TYPE CODE Electronic timer with manual override for solenoid valves with ISO 4400 pins 88122627 DIMENSIONS AND WEIGHT Timer rotatable x 180° 20 35* Weight : 0,054 kg. Seal 43 Test button Adjustment on-period (ON) TEST ON OFF 16 24 10 20 30 8 40 32 5 40 0,5 45 2 ON:SEC. OFF:MIN. Solenoid valve de-energised (LED) 90 Solenoid valve energised (LED) 74 52 Solenoid valve with coil standard ISO 4400 pins Adjustment of off-period (OFF) Connector ISO 4400 rotatable x 90° CM 10 (Pg 11P) (not supplied) * +15 mm for connector clearance INSTALLATION - ADJUSTMENT - UTILISATION • Depending on the width of the solenoid valve body, the timer can be rotated 180° around the connection axis. • Properly fit seal between coil, timer and connector seal. • The electronic timer is supplied with three screws of different lengths for securing the connector and timer to the solenoid valve. One of the three screws corresponding to the size of connector is used. • Adjustment is made using the ON and OFF buttons. • The “TEST” button can be used to energise the solenoid valve, if a power supply is connected. 2 IMPULS-PAUSENZEIT-STECKADAPTER Baureihe 881 EINSTELLBARER IMPULSGEBER zur Montage auf Magnetventile FUNKTIONSPRINZIP Wandelt eine kontinuierlich anstehende Spannung in eine Folge von EIN-Signalen («ON») von 2 bis 40 Sekunden und AUS-Signalen («OFF») einstellbar zwischen 0,5 bis 45 Minuten um. 1 Versorgungsspannung am Eingang 0 1 Ausgangssignal für Magnetventil 0 ON OFF ON : einstellbar von 2 bis 40 Sekunden OFF : einstellbar von 0,5 bis 45 Minuten ANWENDUNGEN Dieser elektronischer Zeitgeber, der einstellbare Impulse erzeugt, ist insbesondere zur automatischen Steuerung der Kondensatentleerung von Lufttrocknern oder Kompressoren geeignet, da er zeitabhängig Magnetventile in regelmäßigen, einstellbaren Abständen starten kann. Andere Anwendungsbereiche sind Beregnungsanlagen, Ausblaseeinrichtungen usw. sowie alle Anwendungen, die eine zeitgesteuerte Taktfolge erfordern. ELEKTRISCHE DATEN SPANNUNG MAX. BELASTUNG ANZUGSTROM MAX. STROMAUFNAHME UMGEBUNGSTEMPERATUR SCHUTZART ZULASSUNG WIEDERHOLGENAUIGKEIT SKALENGENAUIGKEIT ANSCHLUSS : : : : : : : : : : 24V bis 240V DC/AC (50/60 Hz) 1A 10 A max. 10 ms 4 mA –10 °C bis 50 °C IP 65 CSA ± 0,1% ± 10% Der Zeitgeber läßt sich zwischen Spule und Leitungsdose auf allen Magnetventilen mit Anschluß nach ISO 4400/DIN montieren (Leitungsdose gemäß ISO 4400 nicht im Lieferumfang enthalten). GERÄTEAUSWAHL BESTELL-CODE BEZEICHNUNG Impuls-Pausenzeit-Steckadapter mit Testschalter für Magnetventile mit Spulensteckanschluß gemäß ISO 4400 ABMESSUNGEN UND GEWICHT Zeitgeber um 180° umsetzbar Gewicht: 0,054 kg Einstellbare EIN-Zeit (ON) 35* OFF 16 24 10 20 30 8 32 5 40 40 0,5 45 2 ON:SEC. OFF:MIN. 74 52 90 Testschalter Magnetventil mit Spulensteckanschluß gemäß ISO 4400 Magnetventil Spannungslos TEST ON 20 Dichtungsring 43 Magnetventil unter Spannung 88122627 Einstellbare AUS-Zeit (OFF) Leitungsdose CM 10 (Pg 11 P) gemäß ISO 4400 um 90° umsetzbar (nicht im Lieferumfang enthalten) INBETRIEBNAHME - MONTAGE - EINSTELLUNG • Wenn es die Breite des Ventilgehäuses zuläßt, kann der Impuls-Pausenzeit-Steckadapter um 180° zur Anschlußachse gedreht werden. • Montieren Sie auf jeden Fall die Dichtungen zwischen dem Impuls-Pausenzeit-Adapter und der Spule sowie der leitungsdose. • Der Impuls-Pausenzeit-Steckadapter wird mit drei verschieden langen Schrauben zur Befestigung der Leitungsdose sowie des Impuls-Pausenzeit-Steckadapters am Ventil geliefert. Die Wahl der Schraube hängt von der Höhe der verwendeten Leitungdose ab. • Einstellung über die Schalter ON und OFF. • Mit dem Testschalter kann das Magnetventil unter Spannung gesetzt werden, sobald die Versorgungsspannung am Eingang ansteht. 3