Extron PS 128 Power Supply
Transcription
Extron PS 128 Power Supply
: ANT omplete ORoTm for thuecctions, aned IMP .c tr n s in ng th xtro .e on ecti . www stallati e conn Go to uide, in s before er sourc g w n e po user cificatio th spe roduct to p PS 128 Power Supply • Setup Guide The PS 128 Power Supply is a half rack width power supply with 12 outputs. It supplies 12 VDC, 8 A DC power for up to 96 watts. It is compatible with any Extron product featuring 2-pole, 3.5 mm captive screw power connectors. This guide provides instructions for an experienced installer to install and connect the PS 128 Power Supply. Installation Mount the Device 1. Turn off or disconnect all equipment power sources. 2. Mount the PS 128 in one of the following methods (see www.extron.com for optional mounting kits and additional mounting instructions): • Mount the PS 128 in a rack (with an optional 1U mounting kit). • Mount the PS 128 to furniture (with an optional furniture mounting kit). • Mount the PS 128 in an Extron Pole Vault system (with an optional mounting kit). If using an optional mounting kit, see the mounting kit instructions for additional mounting considerations and instructions. Connect Devices and Power The PS 128 can power up to 12 devices simultaneously. For each device to receive power, connect power cables to the 2-pole, 3.5 mm captive screw connectors on the rear panel of the PS 128. Then, apply power to the device. B C A PS 128 100-240VAC 50/60 Hz OUTPUTS RED OVERLOAD 1 2 3 4 5 6 7 8 9 10 11 12 + - + - + - + - + - + - + - + - + - + - + - + - 1.5 A MAX A B C DC output connectors (see the next page) AC power connector (see the next page) Overload LED indicator (see figure 2, A on the next page) Figure 1. Output Connectors and LED Indicator PS 128 Power Supply • Setup Guide (Continued) A DC output connectors — Connect up to 12 devices to these 2-pole, 3.5 mm captive screw connectors (see figure 1, A on the previous page). Wire the connectors as shown in the image to the right. The outputs provide up to 12 VDC and 8 amps of current collectively. WARNING: Electric shock hazard. The two power cord wires must be kept separate while the power supply is plugged in. Remove power before wiring. AVERTISSEMENT : Risque de choc électrique grave. Les deux cordons d’alimentation doivent être tenus à l’écart l’un de l’autre quand l’alimentation est branchée. Couper l’alimentation avant de faire l’installation électrique. NOTE: To verify proper polarity before connection to a device, plug in the power supply with no load and check the output polarity with a voltmeter. Remove power before continuing. 2-Pole Captive Screw Connector Tie Wrap 3/16” (5 mm) Max. SECTION A–A Smooth Ridges A A Power Supply Output Cord B AC input connector — Connect a 100-240 VAC, 50-60 Hz power source to the AC power connector (see figure 1, B) on the rear panel. Operation A RED - OVERLOAD PS 128 12VDC 8A POWER SUPPLY Figure 2. Power and Overload LED indicator A Overload LED indicator — Lights green when power is applied and current draw is normal (under 8 amps) or red when the PS 128 is in a current overload condition (over 8 amps or 96 watts). There is also a duplicate Overload LED indicator on the rear panel (see figure 1, C on the previous page). ATTENTION: • Continued operation in an overload condition may cause premature power supply failure. • Un fonctionnement ininterrompu dans un état de surcharge est susceptible de provoquer une défaillance prématurée de l’alimentation électrique. NOTE: To identify a shorted output, unplug the outputs one at a time until the LEDs light green. Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron Asia +65.6383.4400 Extron China +86.21.3760.1568) Extron Australia +61.8.8351.2188 Extron Europe +31.33.453.4040 Extron Japan +81.3.3511.7655 Extron Middle East +971.4.299.1800 Extron India +91.80.3055.3777 © 2016 Extron Electronics All rights reserved. www.extron.com 68-2900-50 Rev. A 07 16