Joint cover - SpatiulConstruit.ro
Transcription
Joint cover - SpatiulConstruit.ro
Joint covers Presentation The clips afxed joint covers are designed to provide an attractive and decorative low cost solution to the problem of protecting and concealing expansion joints in the structure of a building. They are suitable for use in new and CLIPS AFFIXED JOINT COVERS FOR STANDARD AND SEISMIC STRUCTURAL MOVEMENT JOINTS Extruded Aluminium The extruded aluminium clips afxed joint covers for expansion joints can be used for exteriors and interiors. They are manufactured from 6063 T6 Aluminium alloy and can be nished with a 15 micron thick natural (colourless) anodising layer. They are available from stock in 3 meters lengths and following widths: refurbishment projects for walls, ceilings and oors. Fast and easy to install, the 1. Insert a fastening clip - 50 mm, 60 mm, 70 mm, 90 mm, 120 mm, 140 mm, 180 mm and 210 mm Angle models : clips afxed joint covers are produced in aluminium, PVC and brass extrusions. They will successfully span joints Flat models : 2. Insert head of the following clip alternatively - 50 mm, 60 mm, 70 mm, 90 mm and 120 mm Aluminium clips afxed joint cover can also be supplied powder-coated, upon request, in any RAL colour. All models can be supplied mill or anodised nished. Non standard lengths and drilled proles can be supplied on special orders. *Please contact us for quantities and conditions. up to 150 mm in all types of buildings: ofce buildings, shopping centres, schools, hospitals, hotels, blocks of ats, 3. Push rmly into joint retail development, food stores, Extruded Brass The extruded brass clips afxed joint covers are manufactured from CW 620 N (ASTM C 38000) alloy. They are available from stock in lengths of 3 meters and in 90 mm wide, at model only. Polishing can be made upon request. municipal buildings, leisure centres, factories, airport terminals, rail terminals, etc… Extruded PVC The extruded PVC clips afxed joint covers can be used for exteriors and interiors. The colours white RAL 9016, cream RAL 1015 and grey RAL 7035 are available from stock in lengths of 3 meters and in 50 mm, 70 mm and 90 mm wide, at and angle models. Please contact us for any special model or colour. 4. Clips afxed joint cover in place RAL colours Choice of clips afxed joint covers Clip S: will afx proles onto structural gaps varying in widths between 10 mm and 35 mm clip L 2 models The extruded clips afxed joint covers will successfully cover joints from 10 mm to 150 mm and are afxed by using specially developed spring clips. The at joint covers for façades, walls and ceilings are referenced as W proles. The at joint covers for light oors and heavy duty oors are respectively referenced as LF and F proles. The F proles (F 060, F 070) have been developed to withstand heavy pedestrian trafc and light vehicles up to a maximum axle load of 6 kN. The letter E always denotes a corner prole: EW - ELF. The number which follows the letter(s) always indicates the width of the joint covers in mm. Fixing clips Clip L : will afx proles onto structural gaps varying in widths between 35 mm and 70 mm Clip L * Clip XL *: will afx proles onto structural gaps varying in widths between 60 mm and 110 mm The joint covers can be afxed by using specially designed spring clips manufactured from tempered stainless steel which do not corrode and remain permanently exible without loss of back pressure, thus providing an extremely positive xing. Fixing clips do not require any additional xing such as sealant or screws and plugs attachments. 4 models of xing clips are available from stock and are used in accordance with the width of the structural gap. * These unique and particularly innovative clips are protected by international patents. Special models can be studied and manufactured for specic situations such as chamfered joints. Please consult our technical department for more details. FOLDED JOINT COVERS Clip XXL *: will afx proles onto structural gaps varying in widths between 100 mm and 150 mm The folded joint covers for façades, walls and ceilings, are used when a clips afxed prole cannot be installed. They can be xed using silicone, polyurethane or MS polymer sealant or mechanically xed using screws and plugs. The folded joint covers for oors are designed for heavy duty trafc oors. They have to be mechanically or chemically xed. Please contact us for assistance. * patented models The range of folded joint covers is available in galvanised steel ; mill nish aluminium ; powder coated aluminium ; anodised aluminium ; stainless steel and in thickness varying from 5/10 mm to 30/10 mm. Hot Melt adhesive ADHESIVE JOINT COVERS Brass • Polished BRASS with protection lm The adhesive polished brass joint covers are available in 50, 60, 80 and 100 mm wide. They are supplied in standard lengths of 3 meters, and 13/10 mm thickness. Stainless steel Release paper • Polished STAINLESS STEEL with protection lm The adhesive polished stainless steel joint covers are available in 50, 60, 80 and 100 mm wide. They are supplied in standard lengths of 3 meters and 12/10 mm thickness. © GV2 - 2010 - Tous droits réservés - All rights reserved - GV2/VEDA FRANCE - 52, avenue Marcel Paul - 93297 Tremblay en France Cedex - Tel : 33 (0)1 48 61 70 80 - Fax : 33 (0)1 48 61 70 81 E-mail : [email protected] - web : www.vedafrance.com Edition March 2011 The range of adhesive joint covers is adapted for concealing joints mainly in walls and oor where limited movements are expected. They are not recommended for exterior use. • Silver anodised ALUMINIUM The adhesive silver anodised aluminium joint covers are available in 60, 80 and 100 mm wide. They are supplied in standard lengths of 3 meters. Aluminium CLIPS AFFIXED ALUMINIUM JOINT COVERS VEDA FRANCE L L Fb Fb Clip S*: will affix profiles onto structural gaps varying in widths between 10 mm and 35 mm * Clip XL*: will affix profiles onto structural gaps varying in widths between 60 mm and 110 mm Clip L*: will affix profiles onto structural gaps varying in widths between 35 mm and 70 mm Clip XXL*: will affix profiles onto structural gaps varying in widths between 100 mm and 150 mm Patented models Flat joint covers L (mm) Joint width Fb (mm) 10 - 35 20 - 40 35 - 50 40 - 70 60 - 90 80 - 110 100 - 130 120 - 150 W W W W W W W W - LF LF LF LF LF LF LF LF Angle joint covers L (mm) EW EW EW EW EW 050 - F 060 - F 070 090 120 140 180 210 - ELF ELF ELF ELF ELF 050 060 070 090 120 Recommended clip S S/L S/L L / XL L / XL XL XL / XXL XXL Number of clips by length of 3 lm Floor Wall / Ceiling 10 4 4 10 4 10 4 10 4 10 4/5 10 10 4/5 10 4/5 Note:The above table indicates the minimum width of joint cover (L dimension) recommended according to the initial width of the structural gap (Fb). A 70 mm wide joint cover is recommended to cover a structural gap of 35-50 mm. Of course a joint cover wider than 70 mm can also be used: 90 mm, 120 mm, 140 mm,180 mm, 210 mm. In order to avoid any mistake, it is important to check that the selected models of joint covers and clips are adapted to the concerned situation on job site. NUMBER OF CLIPS FOR ALUMINIUM JOINT COVERS: Wall / Ceiling: it is recommended to use minimum 4 clips per 3 lm length (joint covers ref.W and EW).Extra clips may be needed for fixing onto ceilings and irregular walls. Floor: it is recommended to use minimum 10 clips per 3 lm length (joint covers ref. LF, F and ELF) % Minimum Maximum Si 0.20 Fe Cu Mn 0.35 0.10 0.10 TYPICAL PHYSICAL PROPERTIES Density g/cm3 Melting range °C Coefficient of linear expansion (0 to 100°C) -°C-1x106 Poisson ratio Thermal conductivity Resistivity at 20°C – 1 1 cm Specific heat J / kg°C 2.70 615-655 23.4 0.33 200 3.3 940 Mg 0.45 0.90 Cr Zn Ti Others 0.10 0.10 0.10 0.05 MECHANICAL PROPERTIES AT ROOM TEMPERATURE Temper T6 Strength index R19 Tensile properties Rp 0.2 mini Rm mini A 5.65 0.2%min. UTS min. % mini MPa MPa 160 185 8 CERTIFICATIONS : - extruded aluminium: manufactured in compliance with BS EN ISO 9001. Anodising according to BS 1615 and BS 3987 - Stainless steel clips: certifications ISO 14001 – ISO/TS 16949 – ISO 9001 GV2/VEDA FRANCE - 52, avenue Marcel Paul - 93297 Tremblay en France cedex - Tél. : 33 (0)1 48 61 70 80 - Fax : 33 (0)1 48 61 70 81 E-mail : [email protected] - Web : www.vedafrance.com April 07 - Springer & Co - No contractual document CHEMICAL COMPOSITION OF ALUMINIUM ALLOY 6063 T6 CLIPS AFFIXED PVC JOINT COVERS VEDA FRANCE L L Fb Fb Clip S*: will affix profiles onto structural gaps varying in widths between 10 mm and 35 mm * Clip XL*: will affix profiles onto structural gaps varying in widths between 60 mm and 110 mm Clip L*: will affix profiles onto structural gaps varying in widths between 35 mm and 70 mm Patented models Joint width Fb (mm) 10 20 35 40 - 35 40 50 70 Flat joint covers L (mm) W W W W - LF LF LF LF 050 060 070 090 Angle joint covers L (mm) Recommended clip EW - ELF 050 EW - ELF 060 EW - ELF 070 EW - ELF 090 S S/L S/L L / XL Number of clips by length of 3 lm Wall / Ceiling Pedestrian Floor 10 5 5 10 10 5 5 10 The colours white RAL 9016, cream RAL 1015 and grey RAL 7035 are available from stock in lengths of 3 meters and in 50 mm, 70 mm and 90 mm wide, flat and angle models. In order to avoid any mistake, it is important to check that the selected models of joint covers and clips are adapted to the concerned situation on job site. TECHNICAL CHARACTERISTICS TEST METHOD Density 1.52 g/cm3 Vicat fusion point 80°C Modulus of elasticity 3200 N/mm DIN 534457 Tensile strength 65 N/mm2 DIN 53455 Ball hardness 120 N/mm DIN 53446 Water absorption 0.04 % DIN 53495 Bending stress 92 N/mm DIN 53452 Elongation 65 % DIN 53455 Notch impact strength at 23 °C 5.5 KJ/m Linear tolerance +/- 0.7 % Linear expansion coefficient 8 x 10 Fire resistance B2 DIN 53479 DIN 53460/B 2 2 2 DIN 53453 DIN 16941 K -1 DIN 53752 PVC joint covers do not contain any lead, cadmium, formaldehyde and are suitable for exterior use. The clips affixed PVC joint covers are made without any recycled material, according to the latest available technology. CERTIFICATIONS : - PVC: manufactured in compliance with ISO 9001 - Stainless steel clips: certifications ISO 14001 – ISO/TS 16949 – ISO 9001 GV2/VEDA FRANCE - 52, avenue Marcel Paul - 93297 Tremblay en France cedex - Tél. : 33 (0)1 48 61 70 80 - Fax : 33 (0)1 48 61 70 81 E-mail : [email protected] - Web : www.vedafrance.com April 07 - Springer & Co - No contractual document -5 2 Couvre joints percés - fraisés Drilled and countersunk joint covers Série CJE - PF Les couvre joints CJE-PF sont conçus pour protéger et habiller les joints de façades, murs, plafonds et sols. Esthétiques, décoratifs et économiques, ils peuvent être utilisés à l’intérieur ou à l’extérieur. Pré-percés et fraisés, ils sont faciles à installer, et sont utilisés en travaux neufs et en rénovation pour des joints de 10 à 200 mm. Ils peuvent être installés dans tous types de bâtiments : centres commerciaux, aéroports, gares, immeubles de bureaux, ou d’habitation, hôpitaux, galeries marchandes, écoles, super et hypermarchés, hôtels, bâtiments municipaux, centres de loisirs, usines, etc. This range of joint covers is designed to provide an attractive and decorative low cost solution to the problem of protecting and concealing expansion joints in the structure of a building. Drilled and countersunk, they are suitable for use in new or refurbishment projects for walls, ceilings and oors, for gaps up to 200 mm. They can be installed in all types of buildings : ofce buildings, shopping centres, schools, hospitals, hotels, blocks of ats, retail development, food stores, municipal buildings, leisure centres, factories, airport terminals, rail terminals, etc... CJE - PF 120 120 10 à 50 CJE - PF 140 140 10 à 75 3 aluminium brut / mill nish aluminium Options possibles : Anodisation, laquage... Options : Anodization, powder coating... Fixations possibles : - Vis chevilles (nous consulter pour préconisation) - Scellement chimique Ved Poxy Installation : CJE - PF 320 320 10 à 200 - Using screws and plugs (please contact us) - Pure epoxy chemical anchoring (ref to our VED POXY data sheet). © GV2 - 2010 - Tous droits réservés - All rights reserved - GV2/VEDA France - 52, avenue marcel Paul - 93297 Tremblay en France Cedex - Tel : 33 (0)1 48 61 70 80 - Fax : 33 (0)1 48 61 70 81 E-mail : [email protected] - web : www.vedafrance.com Edition Novembre 2010 Référence / Prole number S [mm] largeur / Width [mm] Fb [mm] ouverture / Gap up to Longueur standard [m] / Standard length Matière / Material Couvre joint Trac moyen / Intense Joint cover Regular / Heavy trafc Série CJE - MT Les couvre joints CJE pour tracs moyen et intense sont conçus pour S protéger et habiller les joints au sol. Ils sont utilisés dans tous types de bâtiments : Centres commerciaux, écoles, hôpitaux, bureaux, gares, aéroports, etc. Série CJE - GT The regular and heavy range of joint covers is designed for protecting and S concealing ground joints. They can be installed in all types of buildings : Commercial centers, schools, hospitals, ofce buildings, rail terminals, airports, etc. Série CJE - MT Couvre joint de dilatation moyen trac Regular trafc joint cover Série CJE - GT Couvre joint de dilatation trac intense Heavy trafc joint cover Référence / Prole number CJE - MT 60 CJE - MT 80 CJE - MT 100 CJE - GT 80 CJE - GT 120 CJE - GT 170 Fb [mm] ouverture / Gap up to 30 50 70 50 80 120 S [mm] largeur / Width 60 80 100 80 120 170 Composition / Material Aluminium anodisé / Anodized aluminium Longueur standard [m] / Standard Length 3 Installation : Fixation : VED-Poxy : scellement chimique pur Epoxy VED-Poxy, pure epoxy sealant. ou Vis Ø 3,5 x 35 mm - Chevilles Ø 5 x 25 mm perçage tous les 30 cm or Screws Ø 3,5 x 35 mm - Plug Ø 5 x 25 mm drilling every 30 cm ou 2 bandes hot melt épaisseur 2 mm or Hot melt adhesive strips: thickness 2 mm use 2 strips © GV2 - 2010 - Tous droits réservés - All rights reserved - GV2/VEDA France - 52, avenue marcel Paul - 93297 Tremblay en France Cedex - Tel : 33 (0)1 48 61 70 80 - Fax : 33 (0)1 48 61 70 81 E-mail : [email protected] - web : www.vedafrance.com Edition Mars 2011 Présentation Folded joint covers For gaps up to 500 mm Serie CJP The folded range of joint covers is designed to provide an attractive and decorative low cost solution to the problem of protecting and concealing expansion joints in the structure of a building. They are suitable for use in new refurbishment projects for walls, ceilings and floors, for gaps up to 500 mm. Fast and easy to install, they can be fixed using silicone, polyurethane or MS polymer sealant or mechanically fixed usng screws and plugs. The folded joint covers for floors are designed for heavy duty traffic floors. They have to be mechanically or chemically fixed. Please contact us for assistance. They will successfully span joints up to 500 mm in all types of buildings : office buildings, shopping centres, schools, hospitals, hotels, blocks of flats, retail development, food stores, municipal buildings, leisure centres, factories, ariport terminals, rail terminals, etc... References Dimensions Gap [Fb] References Dimensions Gap [Fb] CJP - W200 15 + 170 + 15 = 200 0 to 75 CJP - EW125 10 + 50 + 110 + 15 0 to 75 CJP - W250 15 + 220 + 15 = 250 75 to 100 CJP - EW175 10 + 50 + 160 + 15 75 to 100 CJP - W300 15 + 270 + 15 = 300 100 to 150 CJP - EW225 10 + 50 + 210 + 15 100 to 150 CJP - W350 15 + 320 + 15 = 350 150 to 200 CJP - EW275 10 + 50 + 260 + 15 150 to 200 CJP - W400 15 + 370 + 15 = 400 200 to 250 CJP - EW325 10 + 50 + 310 + 15 200 to 250 CJP - W450 15 + 420 + 15 = 450 250 to 300 CJP - EW375 10 + 50 + 360 + 15 250 to 300 CJP - W500 15 + 470 + 15 = 500 300 to 350 CJP - EW425 10 + 50 + 410 + 15 300 to 350 CJP - W550 15 + 520 + 15 = 550 350 to 400 CJP - EW475 10 + 50 + 460 + 15 350 to 400 CJP - W600 15 + 570 + 15 = 600 400 to 450 CJP - EW525 10 + 50 + 510 + 15 400 to 450 CJP - W650 15 + 620 + 15 = 650 450 to 500 CJP - EW575 10 + 50 + 560 +15 450 to 500 The range of folded joint covers is available in galvanised steel ; mill finish aluminium ; powder coated aluminium ; anodised aluminium ; stainless steel and in tickness varying from 5/10 mm to 50/10 mm. © GV2 - 2010 - Tous droits réservés - All rights reserved - GV2/VEDA France - 52, avenue marcel Paul - 93297 Tremblay en France Cedex - Tel : + 33 (0)1 48 61 70 80 - Fax : + 33 (0)1 48 61 70 81 E-mail : [email protected] - web : www.vedafrance.com Edition April 2010 Angle folded joint covers Flat folded joint covers Fb Fb Standard drilling : - Drilled on one side every 400 mm, first and last hole at 10 cm from both ends, wich 7 means 7 holes per length of 3 meters. - Hole ø 8 mm ; countersunk 10 mm. Special drillings - Drilled on both sides, one standard hole on one side and one oblong hole on the other side or 2 oblong holes. - A special adhesive polyethylene tipe can be used for waterproofing and sound insulation (refer to our VEDALEN 111 G TWB B1 data sheet). Installation : - Using screws and plugs or our VED POXY pure epoxy chemical anchoring (ref to our VED POXY data sheet). Driller, countersunk round hole one side, oblong hole on the other side Edition April 2010 Drilled, countersunk one side Drilled, countersunk oblong holes on both sides © GV2 - 2010 - Tous droits réservés - All rights reserved - GV2/VEDA France - 52, avenue marcel Paul - 93297 Tremblay en France Cedex - Tel : + 33 (0)1 48 61 70 80 - Fax : + 33 (0)1 48 61 70 81 E-mail : [email protected] - web : www.vedafrance.com Profilés souples d’obturation Compression profiles Série KLM Présentation Profilés souples à encastrer (pouvant être collés) pour la réalisation rapide et économique de joints verticaux et horizontaux, extérieurs ou intérieurs. Presentation Compression profile (to be glued or not) for the easy and economical sealing of vertical and horizontal, Référence / Profile number KLM 10 KLM 20 KLM 25 KLM 30 KLM 40 KLM 50 KLM 60 KLM 70 KLM 80 a [mm] largeur / width 15 20 25 30 40 50 60 70 80 f [mm] hauteur / depth 20 20 27 28 38 45 55 60 70 Fb [mm] mini / maxi 7 -12 12 - 17 17 - 21 20 - 24 25 - 34 35 - 44 45 - 54 55 - 64 65 - 70 Caractéristiques : Les profilés KLM et KLP standards sont fabriqués selon la norme DIN 18541, caractérisée par un allongement à la rupture supérieur à 350 %, une excellente résistance aux agents chimiques et au vieillissement, une élasticité permanente comparable à celle du caoutchouc. Characteristics : KLM and KLP compression profiles are manufacturated according to the DIN 18541 standard : elongation at break > 350 %, excellent resistance to chemicals and to ageing, permanent elasticity equivalent to that of natural rubber. © GV2 - 2010 - Tous droits réservés - All rights reserved - GV2/VEDA France - 52, avenue marcel Paul - 93297 Tremblay en France Cedex - Tel : 33 (0)1 48 61 70 80 - Fax : 33 (0)1 48 61 70 81 E-mail : [email protected] - web : www.vedafrance.com Edition Septembre 2010 indoor and outdoor joints. Profilés souples d’obturation Compression profiles Série KLP Utilisation En fonction de conditions particulières d’utilisation telles que résistance aux huiles et bitume, sollicitations importantes avec températures KLP 30 extrêmes, risque d’incendie, innocuité physiologique, les profilés KLM et KLP peuvent être fabriqués à partir de matières premières spécifiques selon DIN 7865, ASTM D638, ASTM D746. KLP 15/20/25/35/50/90 Conditions of use Depending on conditions of use such as resistance to oils and bitumen, large movements at extreme temperatures, fire resistance, KLP 15/20/35/50/90 physiologically safe, the KLM and KLP profiles can be manufactured from selected raw materials according to DIN 7865, ASTM D638 KLP 10/40/60 and ASTM D746. EKLP 35/60 EKLP 35/60 ANGLE CORNER EKLP EKLP Référence / Profile number KLP 10 KLP 15 KLP 20 KLP 25 KLP 30 KLP 35 KLP 40 KLP 50 KLP 60 KLP 90 a [mm] largeur / width 17 20 25 30 50 35 60 50 60 90 40 90 f [mm] hauteur / depth 20 20 25 30 35 35 40 40 50 60 35 50 fb [mm] mini / maxi 7-12 9-15 13-17 17-22 19-25 19-25 20-35 25-34 25-30 35-42 19-25 25-30 35 ANGLE CORNER ANGLE 60 CORNER Couleur : Noir ou gris. Egalement possible dans toutes les teintes RAL ou selon échantillon spécifique. Nous consulter. Colour : Black or grey. Other colours available according to the RAL chart of colours or to match with specific sample. Please consult us. © GV2 - 2010 - Tous droits réservés - All rights reserved - GV2/VEDA FRANCE - 52, avenue Marcel Paul - 93297 Tremblay en France Cedex - Tel : 33 (0)1 48 61 70 80 - Fax : 33 (0)1 48 61 70 81 E-mail : [email protected] - web : www.vedafrance.com Edition Mars 2010 KLP 30