NOTICE SPX-015_fr,ang
Transcription
NOTICE SPX-015_fr,ang
NOTICE D’UTILISATION OWNER’S OPERATING MANUAL SPX 015 Table de mixage professionnelle Stereo Sound Mixer 1 2 FONCTIONS 12. VU METRE MASTER Indication de niveau de sortie master droite et gauche 1. ENTREE MICRO DJ Entrée micro combo ; jack 6.35 ou XLR 3 broches 13. EQUALISEUR MASTER L’équaliseur 3 bandes permet une réponse en fréquence du master. L’équaliseur permet une atténuation ou une amplification de 12 dB au maximum pour chaque bande. 2. MASTER Potentiomètre de réglage du niveau de sortie master (1) du mixage 3. NIVEAU MICRO Réglage du micro de sortie de la voie micro DJ 14. ENTREES PHONO/CD Branchez votre platine disque ou votre lecteur CD dans l’entrée PHONO/CD. Sélectionnez le bouton PHONO CD pour l’entrée désirée. 4. GAIN Réglage du niveau d’entrée de la voie, un bon réglage permet d’éviter la distorsion 15. ENTREES LINE/CD Entrées sur connecteur RCA pour CD, K7, Tuner, Vidéo … 5. NIVEAU CANAUX 1 ET 2 Fader de réglage du niveau de sortie des voies 1 et 2 16. BOUTON PHONO/CD Le bouton poussoir situé à côté des entrées des canaux 1 et 3 bascule le type d’entrée de PHONO à CD 6. BOUTON CROSSFADER « ASSIGN » Les 4 canaux peuvent être assignés de chaque côté du crossfader en sélectionnant avec les boutons. Si la même voie est assignée de chaque côté du crossfader, le son sera coupé à chaque extrémité, mais audible en position centrale. 17. MASSE Raccordement de la masse des platines vinyles 18. RECORD Sortie sur connecteur RCA pour l’enregistrement 7. CROSSFADER Le Crossfader peut être assigné à chacun des 4 canaux en ajustant le bouton ASSIGN par rapport au numéro correspondant 19. MASTER Potentiomètre de réglage du niveau de sortie master (1) du mixage 8. SORTIE CASQUE Fiche jack 6.35 pour la sortie de pré écoute au casque 20. ALIMENTATION SECTEUR Fiche standard IEC de raccordement secteur, 220/240 volts 9. PRE ECOUTE Bouton de pré écoute au casque de la voie 21. FUSIBLE Logement du fusible de protection, toujours remplacer ce fusible par un autre de même valeur 10. NIVEAU CASQUE Potentiomètre de réglage du niveau casque 11. POWER Interrupteur marche/arrêt du mixage (Note : toujours mettre en marche le mixage avant l’amplificateur) 3 4 1. SPECIFICATIONS : SENSIBILITE/IMPEDANCE : DJ/MICRO PHONO CD/LIN NIVEAU DE SORTIE : MASTER (sortie maxi 8V) REC (Sortie maxi 8V) PHONES (Sortie maxi 420 mV) 2. 3mV/1 Kohms 3mV/51 Kohms (RIAA) 150mV/100 Kohms 3. 775mV/600ohms asymétrique 380 mV/600 ohms 380 mV/80 ohms 20 Hz≈20KHz±0.5dB (RIAA±2dB) DISTORTION HARMONIQUE TOTALE 0.01% SEPARATION STEREO > 45dB RAPPORT SIGNAL/BRUIT: DJ MIC PHONO CD/LINE 80dB 70dB 85dB DIMENSIONS 4. DJ Channel LEVEL Control: GAIN Controls: Correct setting of the controls for input Gain for every channel is crucial for getting a good, strong signal without noise or distortion. 5. Channel Level Control: The channel fader adjusts the overall volume of the channel. The faders of the stereo channels control both left and right signal at same time. 6. Crossfader ASSIGN Switch: Any of the four music channels can be assigned to either side of the crossfader by the setting of these switches. NOTE: If the same channel is assigned to both sides of the crossfader at either extreme that channel will be muted but the channel will be live when the crossfader at it’s center position. This setting can give the effect of ‘fader dub fading’ when crossfader is used from it‘s center to either extreme. 7. Removeable CROSSFADER: This 45mm crossfader is fully assignable to any of the four main music channels set by the ASSIGN switches. ±12dB@100Hz, 1K, 10 KHz 8 PHONES: This is a 1/4” stereo jack socket mounted on the front face of the mixer for you to attach your headphones. 310 x 236 x 107mm 9. POIDS MASTER Level: This rotary control sets the level present at the MASTER unbalanced RCA jack outputs. Controls the overall level of the DJ channel being mixed onto the Master outputs. REPONSE EN FREQUENCE : CONTROLE DE TONALITE : Boost/cut@center Frequency MICrophone Input: A Combination XLR & 1/4“ jack sockets mounted on the front face of the mixer for connecting your microphone and offer both balanced or unbalanced microphone connections. 3,4Kg CUE Switch: This switch determine which source is heard in the headphones. 10. Headphone LEVE Control: This control varies the volume in your headphones, the volume of the signal heard through the headphones. 5 6 11. Power Switch: SPECIFICATIONS This switches the AC power to the mixer ON or OFF. Note: Be sure to switch on the power to your mixer before switching on the amplification system. Input Sensitivity/ Impedance: 12. MASTER VU Meter: This VU meter shows the signal level of the mixer Master output. 13. MASTER EQUALIZER The 3-band equalizers that allow the user to adjust the frequency response of the Master bus signal respectively. The equalizers provide a maximum 12dB of cut/boost for each frequency. 3mV / 1KOhms PHONO 3mV / 51KOhms (RIAA) CD/LINE 150mV / 100KOhms Output Level/ Impedance: 14. PHONO/CD Inputs: Plug your turntables or line device in here. Select the PHONO/CD switch to the desired input. DJ MIC MASTER (Max. Output: 8V) 775mV/600Ohms Unbalanced REC (Max. Output: 8V) 380mV/600Ohms PHONES (Max. Output: 420mV) 380mV/8Ohms Frequency Response: 15. LINE/CD Inputs: These inputs are unbalanced RCA jacks, connect stereo audio from Hi Fi VCRs, cassette and reel-to-reel tape decks, CD players, VDPs, Tuners, even synthesizers or other mixing consoles. 16. PHONO/ CD Switch: The push button switches beside channel 1and 3 inputs change the input type from Phono to CD. 20Hz~20KHz ±0.5dB (RIAA ±2dB) Total Harmonic Distortion: 0.01% (Rated output) Stereo Separation: More than 45dB Signal-To-Noise Ratio: 17. GND: The GND is a terminal for grounding turntables to eliminate hum. 18. Record Outputs: This outputs is used for additional feed to such items of equipment as tape records. The output level of the signal is not affected by the Master Level control. 19. Unbalanced Master Outputs: These stereo outputs are low impedance, unbalanced RCA jacks controlled by the Master Level. DJ MIC 80dB PHONO 70dB CD/LINE 85dB Tone Control: Boost/Cut@Center Frequency ±12dB@100Hz, 1K, 10KHz Dimensions: 310mm* 236mm* 107mm Weight 3.4kg 20. MAINS Connection: A standard IEC AC power socket for connecting to the main AC supply. Before you connect your Mixer to the mains, please make sure that your local voltage matches the voltage required by the unit! CAUTION: The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed 21. FUSE Holder: on the apparatus. The IEC power socket has an integral fuse holder that takes a 20mm fuse. Always replace a blown fuse with the same type as specified on the rear of the Mixer. -8667 8