microscoop 100 d - nvp
Transcription
microscoop 100 d - nvp
MICROSCOOP 100 D L - 04D S - A 2000 - 12 - 14 1/4 DOC 010 2320 42° 1500 1290 1170 1030 600 220 835 1645 1525 1430 4915 1050 980 2100 36° 1840 1890 3190 Capacities Weights Tramming capacity ...................................1 000 kg (2 200 lb) Breakout force, lift..................... 10.7 kN - 1 094 kg (2 407 lb) Breakout force, tilt..................... 36.9 kN - 3 766 kg (8 285 lb) Tipping load ...................................................2 941 (6 470 lb) Bucket std. ............................. 0.54 m³ ( 0.7 yd³), 500 BNH lip Operating weight.......................................3 300 kg (7 260 lb) Total loaded weight...................................4 300 kg (9 460 lb) Axle weights without load front axle .............................................1 300 kg (2 860 lb) rear axle ..............................................1 900 kg (4 180 lb) Axle weights with load front axle .............................................2 800 kg ( 6 160lb) rear axle ..............................................1 400 kg (3 080 lb) Bucket motion times Raising time ............................................................... 2.6 sec. Lowering time ............................................................ 1.5 sec. Tipping time ............................................................... 4.1 sec. Driving speeds forward and reverse Loaded ............................................ 0 to 9 kph (0 to 5.6 mph) SANDVIK TAMROCK SECOMA se reserve le droit de modifier sans préavis les caractéristiques techniques de cette notice. aprod1200 Microscoop 100 D Spec. no: L - 04D S - A 2000 - 12 - 14 2/4 Service capacities Buckets hydraulics Fuel tank .................................................... 40 litre (10.5 gal.) Hydraulic oil tank........................................ 62 litre (16.4 gal.) Hydrostatic transmission oil tank.................. 31 litre (8.2 gal.) Full hydraulic open center system with one gear pump. Oil flows to bucket hydraulic system from the steering pump, when steering is not used. Equipped with mechanical dual control lever. Engine Diesel engine ............................................. Deutz F3L 912 W Output .......................................... 33 kW (45 hp) / 2 500 rpm Torque............................................ 170 Nm (lb-ft) / 1500 rpm Number of cylinders ...................................................In line 3 Displacement .......................................................... 2 827cm³ Cooling system....................................................... Air cooled Combustion principle................ 4-stroke, 2-stage combustion Electric system ................................................................ 12 V Air filter ..................................................... Oil bath air cleaner Exhaust system..................................... ECS catalytic purifier Transmission Transmission................................... Hydrostatic transmission variable flow, fully reversible Pump................................................. Linde, 0 to 42 cm³ / rev Motor ................................................ Linde, fixed 35 cm³ / rev Transfer case Type ............................................................................... Gear Location...................................................................Rear axle Axles Front and rear Tamrock, fixed No-spin in front axle Central hinge oscillating ................................................. ± 10° Main components: Control valve....................................Commercial hydraulics Lift cylinder (1) ................................ø 100/60 mm, Tamrock Tilt cylinder (1) ................................ø 120/60 mm, Tamrock Fittings ............................................................................JIC Pressure settings: Main relief valve.................................... 14.0 MPa (140 bar) Bucket tilt .................................................. 6.0 MPa (60 bar) Bucket roll-back .................................... 18.0 MPa (180 bar) Boom raise ........................................... 18.0 MPa (180 bar) Boom lower............................................... 6.0 MPa (60 bar) Frame Rear and front frame ..................... Welded steel construction Material.........................................................................E 36.3 Central hinge ............................................ Spherical bearings (large angle) Electrical equipment Alternator ............................................................... 14 V, 45 A Battery ........................................................... 1 x 12 V, 95 Ah Starter................................................................ 1.7 kW, 12 V Lights....................................................... 2 pcs in front, 55 W 2 pcs in rear, 55 W Wheels Tyres ................................................................. 7.50 x 15, L5 Air pressure, front & rear............................ 350 kPa (3.5 bar) Steering..............................................2 hydraulic cylinders Steering control .........................Frame steering, control lever Articulation angle............................................................ ± 36° Main components: Hydraulic pump ............................................................. HPI Control valve .......................................................... Danfoss Steering cylinders (2) ............... ø 60 mm (2.36´´), Tamrock Optional equipment Bucket width 950 mm (37 ´´), 0.5 m³ (0.7 yd³). FOPS-ROPS canopy. Back up alarm. Emergency steering system. Spare rim and tyre (Xmine D2). Radio remote control. Pressure settings: Main relief valve ................................... 14.0 MPa (170 bar) Port relief valves................................... 17.5 MPa (175 bar) Service Brake ........................... Hydrostatic transmission Actuation ....................................................................... Pedal Parking and Emergency Brakes Type ................................................... Hydraulic oil immersed multiple disc brakes inclosed in the rear axle Actuation ................................................... Emergency button Spring applied, hydraulically released SANDVIK TAMROCK SECOMA se réserve le droit de modifier sans préavis les caractéristiques techniques de cette notice. SANDVIK TAMROCK SECOMA S.A., B.P. 46 - 69881 Meyzieu Cedex, France Tel. int. + 33 4 72 45 22 00, Telex 300526 F Telefax int. + 33 4 7831 7980 MICROSCOOP 100 D L - 04D S - A DOC 010 SPEED (km/h) 0 10 20 30 40 50 60 0 1 2 3 4 5 GRADEABILITY & SPEED 6 7 8 9 2000 - 12 - 14 3/4 GRADE (%) SANDVIK TAMROCK SECOMA se reserve le droit de modifier sans préavis les caractéristiques techniques de cette notice. aprod1200 SANDVIK TAMROCK SECOMA se réserve le droit de modifier sans préavis les caractéristiques techniques de cette notice. 0 10 20 30 40 50 60 0 50 100 200 250 Slope / Grade Loaded speed (kph) Empty speed (kph) 300 0% 20 % ONE WAY DISTANCE IN METRES 150 1 000 kg 8.5 km/h 0.5 min. 3% 350 Hor./0 8.5 8.5 400 1:5/20 7.1 8.5 Fixed cycle time includes the time for filling, dumping, turning and accelerating Payload Overall speed limit Fixed cycle time Rolling resistance Basic data for calculations : PRODUCTIVITY CURVE 450 Microscoop 100 D Spec. no: L - 04D S - A 2000 - 12 - 14 4/4 SANDVIK TAMROCK SECOMA S.A., B.P. 46 - 69881 Meyzieu Cedex, France Tel. int. + 33 4 72 45 22 00, Telex 300526 F Telefax int. + 33 4 7831 7980 TONNES PER HOUR