HALL 10-1940-BWT007U - Leds-C4

HALL
10-1940-BWT007U
IN
Design by Nahtrang design
TECHNICAL CHARACTERISTICS
The photograph may not match the reference
exactly. Please read the product description to
identify the finish.
Type:
Table lamp
IP Protection degrees:
IP20
Location:
DRY
Light source 1:
3 x E26
18W
Maximum lamp length: 140.00 mm
Maximum lamp diameter: 52.00 mm
Total power consumption (W):
54
Voltage / Frequency:
120V/60Hz
Warranty (Years):
2
Units per box:
1
Pes net (lb):
9.78
EAN:
8435381437190
Stability:
15º
MATERIALS / FINISHES
Download photometric file .ldt /.ies
Structure material: Steel
Diffuser material: Fabric shade
Methacrylate
Structure finish:
Diffuser finish:
Matt
white
LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of
the product.
Please consult the sales team to clarify any doubt.
White
Tinted
(+34) 973 468 100
[email protected]
www.leds-c4.com
Luminaire
Code
10-1940-BW-14
Name
Sobremesa HALL 3x18W E27 P196
Line
Eulumdat
Measurem.
Code 10-1940-BW-14
Name Sobremesa HALL 3x18W E27 P196
Date 15-07-2014
Lamp
Code
Number
Position
Efficiency
80.87%
Coordinate system
CG
Total Flux
Maximum value
452.00 cd
Position
C=30.00 G=35.00
Asymmetrical
440 mm
440 mm
Height
Height
GENIE ESAVER 18W/827
3
3300.00 lm
Round Luminaire
Round Luminous Area
Diam.
Diam.
230 mm
230 mm
Horizontal Luminous Area
Emitting area on Plane 0°
Emitting area on Plane 90°
0.152053 m2
0.101200 m2
0.101200 m2
Emitting area on Plane 180°
Emitting area on Plane 270°
Glare area at 76°
0.101200 m2
0.101200 m2
0.134979 m2
Symmetry Type
Measurement Distance
Asymmetrical
0.00
Maximum Gamma Angle
Measurement Flux
180
3300.00 lm
Operator
Temperature
Humidity
Notes
Asselum T2
25.00 °C
60.00 %
Source voltage
Source current
Photocell
Luminaire Lamps
Code
Name
GENIE ESAVER 18W/827 GENIE ESAVER 18W/827 - 18.00 W
Line
Eulumdat
C.I.E.
F UTE
33 68 91 65 81
0.53 I + 0.28 T
D DIN 5040
B NBN
Flux [lm]
1100.00
Pow. [W] Q.ty
18.00
3
B21
BZ 6
Diam=440mm
90
135° Gamma Angles
180°
165°
150°
135°
0
320
180
120°
120°
240
270
160
C Halfplanes
180.0
0.0
270.0
105°
105°
80
90.0
90°
90°
80
75°
75°
160
ULOR
27.92 %
DLOR
52.95 %
RN
34.52 %
240
60°
60°
320
cd
400
45°
LITESTAR
(c)OxyTech Srl www.oxytech.it
30°
15°
0°
15°
30°
45°
Page 1
LEDS, C4 S.A.
CIF/VAT: A-59.410.910
C/ Afueras s/n -TORA- 25750
(LLEIDA) SPAIN
TEL: 34 (73) 46 81 02
FAX: 34 (73) 46 81 06
SHEET: 1/1
EDITION: 01
REF: 10-1940U
FIGURE Nº 1. UNPACK THE FIXTURE: CHECK THE
CONTENTS OF THE BOX. YOU SHOULD RECEIVE:
FIGURE Nº 1. DÉBALLER LE PLAFONIER: VÉRIFIER LE
CONTENU DU CARTON, VOUS DEVEZ RECEVOIR:
2
3
4
5
6
I/0
CAUTION:
ATTENTION:
"Warning", "This product is to be
installed by a qualified electrician
only."
"Suitable for dry locations only"
"Attention", le raccordement
électrique sera effectué par un
téchnicien électricien qualifié"
"Adéquat seulement en lieux secs."
CAUTION:
1.- Wrong lighting installation can be dangerous for your safety.
2.- Before starting, disconnect the power by turning off the general switch of the
electric installation.
3.- Install light bulbs (not provided) that must not exceed markings on the fixture.
4.- To change the bulbs, disconnect the power by turning off the general switch and
wait for the bulbs cool down.
INSTALLATION:
1.- Assembly according to the attached instructions.
ELECTRICAL CONNECTIONS:
ATTENTION:
1. Une mauvaise installation peut compromettre votre sécurité.
2. Déconnecter la tension du réseau d'alimentation avant de réaliser toute opération.
3. Installer les ampoules (non fournies), ne pas utiliser d'ampoules d'un autre type ou
d'une puissance supérieure à celle indiquée sur l'étiquette de la lampe.
4. Pour changer les ampoules, déconnecter la tension du réseau d'alimention et
laisser refroider les ampoules.
INSTALLATION:
1. Suivre le mode d’emploi quand vous faites le montage.
RACCORDEMENTS ÉLECTRIQUES: