INTRODUCTION The DGP2-ZC1 is used to protect doors and
Transcription
INTRODUCTION The DGP2-ZC1 is used to protect doors and
Once it is connected to the network, assign the DGP2-ZC1 to a zone in the control panel as described in Zone Programming (refer to the appropriate control panel Reference & Installation Manual). COMPATIBILITY The Addressable Door Contact can be connected to and used with any Digiplex (DGP-48) and DigiplexNE (DGPNE96) control panel. Connect the DGP2-ZC1 to the communication network as shown in Figure 1 below. SPECIFICATIONS INTRODUCTION The DGP2-ZC1 is used to protect doors and windows. Typically, a magnet (not included) is mounted on a door or window and the contact switch is mounted on the door frame or windowsill (see Figure 1 below). An open zone signal is sent through the communication network to the control panel when the magnet moves away from the reed switch (included). When the magnet returns to its position close to the reed switch, a zone restore signal is sent. The distance between the magnet and the reed switch is determined by the magnet’s specifications. On-board Tamper Switch: Voltage Input: Current Consumption: Operating Temperature: Number of Zones: Power-up Indication: Proper Operation: Locate Indication: Bus Fault Indication: Compatibility: Reed Switch: Dimensions: Figure 1: Connecting the DGP2-ZC1 Yes 9 to 16 VDC 14.2mA typical 0°C to 50°C (32°F to 122°F) 1 standard zone Green LED illuminates Red LED flashes Green LED flashes Green and red LEDs flash alternately Any Digiplex or DigiplexNE control panel Form A, (SPST) reed switch 73.7mm L x 20.3mm H x 30.5mm W 2.9” L x 0.8” H x 1.2” W Une fois branché au réseau, le DGP2-ZC1 doit être assigné à une zone du panneau de contrôle tel que décrit dans la rubrique Programmation de zone (référez-vous au Manuel de référence et d’installation du panneau de contrôle approprié). COMPATIBILITÉ Le contact de porte adressable peut être utilisé avec tout panneau de contrôle Digiplex (DGP-48) et DigiplexNE (DGPNE96). Branchez le DGP2-ZC1 au réseau de communication tel qu’illustré à la Figure 1 ci-dessous. SPÉCIFICATIONS INTRODUCTION Le DGP2-ZC1 est utilisé pour protéger des portes et des fenêtres. Généralement, un aimant (non compris) est installé sur une porte ou une fenêtre et l’interrupteur magnétique est installé sur le cadre de la porte ou de la fenêtre (voir la Figure 1 ci-dessous). Un signal de “zone ouverte” est envoyé au panneau de contrôle par le biais du réseau de communication lorsque l’aimant s’éloigne de l’interrupteur magnétique (compris). Lorsque l’aimant revient à sa position initiale, près de l’interrupteur magnétique, un signal de “zone ouverte rétablie” est envoyé. La distance entre l’aimant et l’interrupteur magnétique est déterminée par les spécifications de l’aimant. Interr. anti-sabotage intégré : Tension d’entrée : Consommation de courant : Température d’opération : Nombre de zones : Indicateur de sous tension: Fonctionnement normal : Indicateur de localisation : Oui 9 à 16 Vcc 14,2 mA typique 0°C à 50°C (32°F à 122°F) 1 zone standard Le voyant DEL vert s’allume Le voyant DEL rouge clignote Le voyant DEL vert clignote Indicateur de panne de communication : Les voyants DEL rouge et vert clignotent alternativement Compatibilité : Tout panneau de contrôle Digiplex ou DigiplexNE Interrupteur magnétique : Dimensions : Forme A, (SPST) interr. magnétique 73,7 mm L x 20,3mm H x 30,5mm L 2,9” L x 0,8” H x 1.2” L Figure 1: Branchement du DGP2-ZC1