Dolphin 9700 Mobile Computer Windows Mobile 6.5 Quick Start Guide

Commentaires

Transcription

Dolphin 9700 Mobile Computer Windows Mobile 6.5 Quick Start Guide
97_QS.book Page 1 Thursday, September 9, 2010 9:57 AM
Dolphin™ 9700
with Windows Mobile® 6.5
Quick Start Guide
97_QS.book Page 2 Thursday, September 9, 2010 9:57 AM
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to
make changes in specifications and other information
contained in this document without prior notice, and the
reader should in all cases consult Honeywell to determine
whether any such changes have been made. The
information in this publication does not represent a
commitment on the part of HII.
HII shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or
consequential damages resulting from the furnishing,
performance, or use of this material.
This document contains proprietary information that is
protected by copyright. All rights are reserved. No part of
this document may be photocopied, reproduced, or
translated into another language without the prior written
consent of HII.
Web Address: www.honeywellaidc.com
Trademarks
Dolphin and HomeBase are trademarks or registered
trademarks of Hand Held Products, Inc. or Honeywell
International Inc. Microsoft, Windows, Windows Mobile,
ActiveSync, and the Windows logo are trademarks or
registered trademarks of Microsoft Corporation. Other
product names or marks mentioned in this document may
be trademarks or registered trademarks of other companies
and are the property of their respective owners.
©2010 Honeywell International Inc. All rights reserved.
97_QS.book Page 1 Thursday, September 9, 2010 9:57 AM
Out of the Box
Verify that the carton contains the following items:
•
•
•
Dolphin 9700 mobile computer (the terminal)
Main battery pack (7.4V Li-ion)
Quick Start Guide
Note: If you ordered accessories for your terminals, verify that
they are also included with the order.
Be sure to keep the original packaging in the event that the
Dolphin terminal should need to be returned for service.
Front Panel
Power Key
Front Speaker
Touch Panel Display
Scan Key
Microphone
Indicator
LED
Volume
Button
Right Button
I/O Connector
Navigation Keys
1
97_QS.book Page 2 Thursday, September 9, 2010 9:57 AM
Back Panel
Battery Door
Hand Strap
Stylus Slot
IRDA Port
Left Button
Stylus Fastener
Image/Scan
Engine Window
Memory Card Socket
SIM Card Socket
Battery Well
Flashlight/
Camera Flash
Color
Camera
Rear Speaker
2
97_QS.book Page 3 Thursday, September 9, 2010 9:57 AM
Available Keyboards
31-Key Numeric Keyboard
SCAN
VOL
PG
TAB
ENT
®
ESC
1
F1
@?!
2
F2
ABC
3
4
F4
GHI
5
F5
JKL
F6
6 MNO
F7
PQRS
8
F8
TUV
F9
9 WXYZ
0
F10
&
7
*.
F3
DEF
ALT
SP
#
,
45-Key QWERTY Keyboard
SCAN
VOL
PG
TAB
ENT
®
! F1
Q
@
A
*
Z
1
F2
W
4
2 F3
3 F4
E
$ F5
R
5
6
Y
;
- F8
) F7
( F6
T
I
U
:
“
+ F9
O
?
S
D
F
G
H
J
K
7
8
9
#
/
\
,
X
C
0
.
V
B
SPACE
N
M
= F10
P
&
L
-
ESC
3
97_QS.book Page 4 Thursday, September 9, 2010 9:57 AM
Install the Main Battery Pack
The 9700 is shipped with the battery packaged separate
from the unit. Follow the steps below to install the main
battery.
1. Release the hand strap near the base of the terminal.
2. Remove the battery door by releasing the door latch
and pulling up with a hinging motion.
3. Insert the battery into the battery well.
4. Replace the battery door. Apply pressure to engage
the door latch.
Note: The battery door must be installed prior to
powering the unit.
5. Reattach the hand strap.
6. Connect the terminal to one of the 9700 series
charging peripherals to charge the main battery pack.
!
4
We recommend use of Honeywell Li-Ion battery packs.
Use of any non-Honeywell battery may result in damage
not covered by the warranty.
97_QS.book Page 5 Thursday, September 9, 2010 9:57 AM
Charging the Dolphin
The initial charging time for the main battery pack is
6 hours, and 8 hours for the internal backup battery.
Connect the terminal to one of the 9700 series charging
peripherals to charge the main battery.
HomeBase
AUX Battery Well
Dock LED
COMM LED
AUX Battery
LED
5
97_QS.book Page 6 Thursday, September 9, 2010 9:57 AM
HomeBase Back Panel
USB Port
Serial Port
DC Power Jack
HomeBase LED Indicators
Green
The terminal is properly seated in the
base.
Orange The auxiliary battery is charging.
Green
The auxiliary battery has completed
charging and is ready for use.
Serial Port Communication
Red
Serial data is being sent from the host
device to the base.
Green
Serial data is being sent from the
base to the host device.
Orange Serial data is being sent in both
directions at the same time.
USB Port Communication
Green
6
A USB connection is established with
the host workstation.
97_QS.book Page 7 Thursday, September 9, 2010 9:57 AM
Charging/Communication Cable
Power Adapter
Cable
Power
Cord
Host
Device
COMM Cable
USB Connector
Or
RS232 Connector
LED Indicators
The light emitting diode (LED) located at the top of the
LCD display flashes and illuminates during resets,
scanning/imaging and taking a picture. This LED can be
programmed by various software applications.
7
97_QS.book Page 8 Thursday, September 9, 2010 9:57 AM
Battery Status Indicator
The Dolphin’s battery status is indicated at the top of the
touch screen in the Navigation Bar.
The battery is charging. The terminal is using an
external power source.
The battery has a full charge.
The battery has a high charge.
The battery has a medium charge.
The battery has a low charge.
The battery has a very low charge. Charge the
battery.
ActiveSync Communication
To synchronize the host workstation and the Dolphin
terminal, ActiveSync 4.5 or higher must be installed and
configured for the appropriate communication type on
both devices. Dolphin terminals ship with ActiveSync
already installed. Therefore, you just need to connect the
Dolphin terminal to the host workstation (via Dolphin
peripheral) to initiate communication.
Note: You can download the most current version of ActiveSync
from www.microsoft.com.
We recommend use of Honeywell peripherals, power
cables, and power adapters. Use of any non-Honeywell
peripherals, cables, or power adapters may cause
damage not covered by the warranty.
!
8
97_QS.book Page 9 Thursday, September 9, 2010 9:57 AM
Installing a Memory Card
1. Press the Power key
to put
the terminal in Suspend Mode.
2. Release the hand strap near the
base of the terminal.
3. Remove the battery door and the
battery.
4. Remove the protective cover over
the memory socket.
5. Unlock the access door to the
memory socket by sliding the
door away from the serial number
label located in the battery well.
6. Lift the door up to expose the
socket.
7. Insert the microSD or microSDHC
card into the socket.
Step 4
Step 5
Step 6
Step 7
Note: Make sure the interface on the
memory card is connected to
the interface in the socket; align
the notch on the card with the
notch of the socket.
8. Close and lock the access door
by sliding the door toward the
serial number label.
9. Replace the protective cover over
the memory socket.
10. Install the battery and the battery
door.
8
Step 4
Step 49
9
97_QS.book Page 10 Thursday, September 9, 2010 9:57 AM
11. Press and hold the RED
approximately 5 seconds.
+ TAB
TAB
®
keys for
12. The decode and scan LEDs flash for approximately
three seconds as the terminal resets.
13. When the reset is complete, the Today screen
displays.
Note: Honeywell recommends formatting all SD cards before
initial use.
10
97_QS.book Page 11 Thursday, September 9, 2010 9:57 AM
Installing a SIM Card
1. Press the Power key
to put
the terminal in Suspend Mode.
Step 4
2. Release the hand strap near the
base of the terminal.
3. Remove the battery door and the
battery.
4. Remove the protective cover
over the SIM socket.
5. Unlock the access door to the
SIM socket by sliding the door
away from the serial number
label located in the battery well.
Step 5
Step 6
6. Lift the door up to expose the
socket.
7. Insert the SIM card into the
socket.
Note: Make sure the interface on the
card is connected to the SIM
Card interface in the socket;
align the beveled corner of the
card with the beveled corner of
the socket.
8. Close and lock the access door
by sliding the door toward the
serial number label.
Step 7
Step 8
Step 9
9. Replace the protective cover
over the SIM socket.
10. Install the battery and the battery
door.
11
97_QS.book Page 12 Thursday, September 9, 2010 9:57 AM
Using the Scan Image Engine
1. Tap Start > Demos
> Scan Demo
2. Point the Dolphin’s terminal at the bar code.
3. Project the aiming beam or pattern by pressing and
holding the SCAN key
side buttons.
SCAN
or one of the terminal’s
4. The red LED lights.
5. Center the aiming beam over the bar code; see
Aiming Options on page 13.
6. When the bar code is successfully decoded, the LED
changes to green and the terminal beeps.
7. The bar code information is entered into the
application in use.
12
97_QS.book Page 13 Thursday, September 9, 2010 9:57 AM
Aiming Options
5300 Red High-Vis Aiming Pattern
5100 Green Aiming Beam
Linear Bar Code
2D Matrix Symbol
13
97_QS.book Page 14 Thursday, September 9, 2010 9:57 AM
Using the Color Camera
1. Tap Start > Demos
> Camera Demo
2. Adjust the camera settings using the menu at the top
of the display screen.
Color
Brightness
Pixels
Zoom
3. Point the terminal's camera
lens at the object you want
to capture. The camera lens
is located on the back panel
of the terminal.
4. Center the object in the
touch screen display.
ENT
5. Press the ENT key
.
The terminal’s red LED
illuminates during picture
capture.
Note: Tap the green arrow
to
review or edit your pictures.
Tap the green box
to exit
the picture review/edit screen.
14
Flash
Camera
Lens
Camera
Flash
97_QS.book Page 15 Thursday, September 9, 2010 9:57 AM
Soft Reset (Warm Boot)
A soft reset re-boots the device without losing RAM data.
1. Press and hold the RED
approximately 5 seconds.
+ TAB
TAB
®
keys for
2. The decode and scan LEDs flash for approximately
three seconds as the terminal resets.
3. When the reset is complete, the Today screen
displays.
Hard Reset (Cold Boot)
A hard reset resets the operating system, restores the
terminal back to factory defaults, and resets the terminal
after a bootloader, keyboard, and kernel upgrade.
!
A hard reset erases all of the data stored in RAM memory
and all RAM installed applications!
1. Press and hold the RED
approximately 5 seconds.
+ ENT
ENT
keys for
2. The decode and scan LEDs light for approximately
3 seconds.
3. The terminal re-initializes.
15
97_QS.book Page 16 Thursday, September 9, 2010 9:57 AM
Technical Assistance
Contact information for technical support, product service,
and repair can be found at www.honeywellaidc.com.
User Documentation
Refer to www.honeywellaidc.com for detailed user
documentation or for localized versions of this Quick Start.
Limited Warranty
Refer to www.honeywellaidc.com/warranty_information
for your product’s warranty information.
16
97_QS.book Page 17 Thursday, September 9, 2010 9:57 AM
97_QS.book Page 1 Thursday, September 9, 2010 9:57 AM
Honeywell Scanning & Mobility
9680 Old Bailes Road
Fort Mill, SC 29707
www.honeywellaidc.com
97-QS Rev C
9/10