passat cc
Transcription
passat cc
Page 1 / 6 Rev. 20140630 PASSAT CC Guide # 11171 ADDENDUM - SUGGESTED WIRING CONFIGURATION SCHÉMA DE BRANCHEMENT SUGGÉRÉ VOLSWAGEN Passat CC 2009-2014 Fuse box (Connector G) Boîte à fusibles (connecteur G) CAN LOW Orange/Brown CAN HIGH Orange/Green Key port connector Connecteur du récepteur de la clé (+)Key Sense Light Green (+) Starter Red/Gray (+)Ignition Light Green/Gray Transponder (+) Starter wire Red/Gray White or Black HARDWARE VERSION HARDWARE VERSION : 3 FIRMWARE VERSION : 4.0+ Date: xx-xx EVO VERSION DU MATÉRIEL INTERFACE MODULE PATENTS PENDING US: 2007-228827-A1 Made in Canada www.fortinbypass.com Service No : 000 102 04 2536 Minimum 3 FIRMWARE VERSION VERSION DU LOGICIEL 75. [ 00 ] VOLKSWAGEN Parts required (not included) 2x 1 amp Diode 1x Vehicle Key 1x Relay 1x 10Amp Fuse This manual may change without notice. www.ifar.ca for latest version. Ce Guide peut faire l'objet de changement sans préavis. www.ifar.ca pour la récente version. Minimum Pièces requises (Non incluses) 2x Diodes amp 1x Clé du véhicule 1x Relais 1x 10 Amp Fusible To complete the installation either use one of the existing keys or order a new valet key from Volkswagen, see next page for more information. Pour compléter l'installation utilisez soit une des clés du véhicule ou commandez une clé valet de Volkswagen, voir page suivante pour plus d'information. This Guide may change without notice. www.ifar.ca for latest version. Ce Guide peut faire l’objet de changement sans préavis. www.ifar.ca pour la récente version. Page 23/ /64 Page DESCRIPTION | DESCRIPTION LED | DEL Blue | Bleu : CAN COMMUNICATION Yellow | Jaune : IGNITION ON Red | Rouge : REMOTE START ON NOT INCLUDED NON INCLUS 2 PIN CONNECTOR: TB CONTROL (WHITE | BLANC) 4 PIN CONNECTOR: DATA-LINK (BLACK | NOIR) Red | Rouge Black | Noir Blue | Bleu White | Blanc 12V Battery (+) | 12V Batterie (+) Ground (-) | Masse (-) DATA DATA 20 PIN CONNECTOR: MAIN HARNESS | HARNAIS PRINCIPAL (WHITE|BLANC) Foot Brake | Frein (pied) Signal Black | Noir Tachometer Pink | Rose Trunk Release | Valise Yellow/Black | Jaune/Noir Hand Brake | Frein à Main Signal Brown/White | Brun/Blanc Hood Status | Capot Statuts Pink/Black | Rose/Noir See configuration Purple/Yellow | Mauve/Jaune Green/White | Vert/Blanc See configuration See configuration Green/Red | Vert/Rouge See configuration White/Black | Blanc/Noir See configuration Lt. Blue | Bleu Pâle 1 2 13 3 12 14 4 5 16 6 17 7 18 8 15 20 9 10 5 4 3 2 1 Copyright © 2012, FORTIN AUTO RADIO INC TOUS DROITS RÉSERVÉS KIA RIO - PUSH-TO-START VEHICLES EQUIPPED WITH AN OEM ALARM Some vehicles must be UNLOCKED to disarm the OEM alarm before remote start. Enable option #12 using the FlashLink Manager. When this option is enabled the module will automatically UNLOCK before remote start and LOCK after the vehicle has remote started. A Yellow | Jaune See configuration Purple | Mauve Lock | Verrouille Purple/White | Mauve/Blanc Unlock | Déverrouille Door Status | Statuts Portes Green | Vert White | Blanc Trunk Status | Statuts Valise Orange AUX 1 Orange/Black | Orange/Noir AUX 2 Dk. Blue | Bleu foncé GWR (Ground While Running) Red/Blue | Rouge/Bleu See configuration Lt. Blue/Black | Bleu Pâle/Noir See configuration 11 19 E B 5 PIN CONNECTOR: CAN-BUS (WHITE | BLANC) Brown | Brun CAN 1 WIRE (SW) Gray/Black | Gris/Noir CAN 2 LOW Gray | Gris CAN 2 HIGH Orange/Brown | Orange/Brun CAN 1 LOW Orange/Green | Orange/Vert CAN 1 HIGH C 6 PIN CONNECTOR: RELAY | RELAIS (RED | ROUGE) COMM2 White/Red | Blanc/Rouge 6 NO2 White/Blue | Blanc/Bleu 5 NC2 White/Green | Blanc/Vert 4 COMM1 Yellow/Red | Jaune/Rouge 3 NO1 Yellow/Blue | Jaune/Bleu 2 NC1 Yellow/Green | Jaune/Vert 1 D VÉHICULES ÉQUIPPÉS D'UNE ALARME D'ORIGINE Certains véhicules doivent être DÉVERROUILLÉS avant le démarrage à distance pour désarmer l'alarme d'origine. A c t i v e z l ' o p t i o n # 1 2 a v e c l e F l a s h L i n k M a n a g e r. Lorsque cette option est activée, le module déverrouille automatiquement avant le démarrage à distance et reverrouille après que le véhicule a démarré à distance. This Guide may change without notice. www.ifar.ca for latest version. Ce Guide peut faire l’objet de changement sans préavis. www.ifar.ca pour la récente version. Page 33/ /64 Page KIA - PUSH-TO-START KEYRIO CONTROL | CONTRÔLE DE LA CLÉ KEY OR VALET KEY REQUIRED | CLÉ OU CLÉ VALET REQUISE To complete the installation either use one of the existing keys or order a new valet key from Volkswagen, see next page for more information. Pour compléter l'installation utilisez soit une des clés du véhicule ou commandez une clé valet de Volkswagen, voir page suivante pour plus d'information. KESSY KEY 1 E or A Dealer Scan- When programming To complete the remote car The key provided by with the Dealer Tool must be used starter installation either use Volkswagen is Scan-Tool the new to initialize the one of the existing keys or customized for the valet key must be new key and order a new valet key from vehicle's VIN and can initialized first Volkswagen not be initialized on reinitialize all the remaining existing (Part #: 2k0837219ABINF). another vehicle. keys. and only after should all the remaining keys be reinitialized. Any keys that are not initialized during the programming procedure will no longer function. Lors de la programmation avec l'ordinateur du concessionnaire, la nouvelle clé doit être la première clé initialisée et seulement après toutes les clés restantes doivent être réinitialisées. Toutes les clés qui ne seront pas réinitialisées ne seront plus fonctionnelles. L'ordinateur du La clé fournie par Pour compléter l'installation concessionnaire Volkswagen est du démarreur à distance utilisez soit une des clés ou personnalisée pour le doit être utilisé commandez une nouvelle clé VIN du véhicule et ne pour initialiser la nouvelle clé et peut pas être valet de Volkswagen réinitialiser (Part #: 2k0837219ABINF). initialisée sur un autre toutes les autres véhicule. clés existantes. This Guide may change without notice. www.ifar.ca for latest version. Ce Guide peut faire version. p l’objet de changement j gsans préavis.pwww.ifar.ca pour la récente p Page 43/ /64 Page KIA RIO -CONNECTION PUSH-TO-START WIRING | GUIDE DE BRANCHEMENTS A15 A14 A13 A12 A11 A8 A5 A4 A3 A2 (-) (-) (-) (+/-) (+) (-) (-) (-) (-) (-) RS7 OUT IGNITION1 (+) RS6 OUT IGNITION2 (+) RS5 OUT ACCESSORY (+) RS4 OUT PARKING LIGHT (+) RS3 OUT PARKING LIGHT (-) 12V BATTERY (+) RS2 IN RS1 Ground | Masse (-) REMOTE STARTER DÉMARREUR À DISTANCE WITH | AVEC DATA-LINK: Direct connection Branchement directe ALWAYS REQUIRED TOUJOURS REQUIS Cut | Coupez Cut | Coupez WITHOUT DATA-LINK: SANS DATA-LINK: BRAKE NOT PRESSED TO START BRAKE PRESSED TO START A9 START (+) RS8 OUT IN RS9 HOOD STATUS IN RS10 HAND BRAKE TRUNK RELEASE OUT RS11 IN RS12 TACHOMETER IN RS13 FOOT BRAKE WHILE RUNNING OUT RS14 IN RS15 TRUNK STATUS IN RS16 DOOR STATUS UNLOCK/DISARM OUT RS17 OUT RS18 LOCK/ARM WITH | AVEC DATA-LINK: NOT REQUIRED WITH DATALINK NON REQUIS EN DATA-LINK PASSAT CC - AUTOMATIC/MANUAL TRANSMISSION B4 B3 Red Black Blue White Red Black 10 Amp Fuse 12V BATTERY Ground B4 B3 B2 B1 A1 Ignition Lock/Arm Unlock/Disarm Door Status Trunk Status Yellow Purple Purple/White Green White Orange Orange/Black (-) Ground While Running Dk. Blue (+) Starter Red/Blue Lt. Blue/Black (+) Foot Brake Black (+/-) Tachometer Pink (-) Trunk Release Yellow/Black (-) Hand Brake Brown/White (-) Hood Status Pink/Black Purple/Yellow Green/White Green/Red White/Black 30 Lt. Blue 87a 85 87 IN IN IN OUT OUT IN IN IN IN OUT OUT IN OUT OUT IN A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 HARDWARE VERSION : 3 FIRMWARE VERSION : 4.0+ Date: xx-xx EVO VERSION DU LOGICIEL VERSION DU MATÉRIEL INTERFACE MODULE PATENTS PENDING US: 2007-228827-A1 Made in Canada www.fortinbypass.com Service No : 000 102 04 2536 Minimum A C C5 C4 C3 C2 C1 75. [ 00 ] 3 Brown Gray/Black Gray Orange/Brown Orange/Green VOLKSWAGEN D4 D3 D2 D1 Minimum CAN 2 LOW CAN 2 HIGH D6 White/Red D D5 White/Blue White/Green Yellow/Red Yellow/Blue Yellow/Green COMM1 NO1 NC1 COMM2 NO2 NC2 See wirecolor.com to learn more on how to do the key wrap. Voir wirecolor.com pour apprendre comment faire le contournement de clé. 86 12V FIRMWARE VERSION HARDWARE VERSION B E O ALL (+) (-) (-) (-) (-) D2 D4 D5 D6 Cut D4 1A Diode D3 RS8 (+) Key Sense Light Green Vert Pâle 1A Diode RS7 C3 (+)Ignition Light Green/Gray Vert Pâle/Gris CAN HIGH Orange/Green Orange/Vert C4 CAN LOW Orange/Brown Orange/Brun RS2 (+)12V Red | Rouge Transponder wire White Blanc (+) Starter Red/Gray | Rouge/Gris This connection is required if the foot-brake needs to be pressed to start the vehicle. Faire se branchement si le frein à besoin d'être appuyé pour démarrer le véhicule. (+)Start Red/Blue Rouge/Bleu RS8 Twisted pair Paire de Fils torsadés Harness from firewall behind BCM Harnais du pare-feu derrière le BCM Key port connector Connecteur du récepteur de la clé Black connector Back view Connecteur Noir Vue de dos Fuse box (Connector G) Boîte à fusibles (connecteur G) Black connector Back view Connecteur Noir Vue de dos Fuse box Boîte à fusibles This Guide may change without notice. www.ifar.ca for latest version. Ce Guide peut faire l’objet de changement sans préavis. www.ifar.ca pour la récente version. Page 53/ /64 Page KIA RIO - PUSH-TO-START PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION 1 Press and hold the programming button: Insert the 4-Pin (Data-Link) connector. x1 HOLD 9 The LED will alternate between BLUE, YELLOW and RED flashes. Appuyez et maintenir enfoncé le bouton de programmation: Insérez le connecteur 4 pins (Data-Link) 9 Les DELS alternent entre un flash BLEU, JAUNE et ROUGE. 2 RELEASE ON Release the programming button when the LED is BLUE. Relâchez le bouton de programmation quand la DEL est BLEU. If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1. Si le DEL n'est pas BLEU débranchez le connecteur 4 pins (Data-Link) et allez au début de l'étape 1. Insert the required remaining connectors. Insérez les connecteurs requis restants. Turn the Ignition to the ON/RUN position. Tournez la clé en position ignition (ON). BLUE BLEU 3 4 IGNITION OFF TURN ON/RUN GN I START LO CK ACC ON FLASH RAPIDLY ON 9 The BLUE LED will flash rapidly. PUSH 9 La DEL BLEU clignotera rapidement. 5 FLASH RAPIDLY IGNITION OFF F TURN OFF OF OFF Turn the Ignition to the OFF position. Tournez la clé à OFF. START LO CK ACC ON PUSH 9 The BLUE LED will turn off. The module is now programmed. 9 La DEL BLEU s'éteint. Le module est programmé. Page 6 / 6 HARDWARE VERSION FIRMWARE VERSION Date: xx-xx EVO-ALL INTERFACE MODULE PATENTS PENDING US: 2007-228827-A1 Made in Canada Service No : Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product. www.fortinbypass.com 000 102 04 2536 Module label | Étiquette sur le module Notice: Mise à jour microprogramme et Guides d’installations Des mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifiez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit. WARNING The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version. MISE EN GARDE L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifier tous les fils et circuits avant d’effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifié. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version. Copyright © 2006-2012, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING TECH SUPPORT Tél: 514-255-HELP (4357) 1-877-336-7797 ADDENDUM GUIDE www.fortinbypass.com WEB UPDATE | MISE À JOUR INTERNET