edxx_steel - acier
Transcription
edxx_steel - acier
Fig EDxx - Globe valves Outside screw & Yoke in cast steel - Robinets soupape en acier coulé à tige extérieure et arcade COBEPEX s.a. Belgium Shut-off globe valve PN16-100 Shut-off globe valve and shut-off globe valve with control cone, shut-off or throttle cone, with flanged or butt weld ends, straight-way or y-pattern body , non-asbestos gland packing and gasket Meets the requirements of PED 97/23/EC, EN 13709. Part -29 - +400 °C Material -20 - +593 °C -47 - +340 °C -70 - +350 °C DIN (ASTM) DIN (ASTM) DIN (ASTM) DIN (ASTM) 1 Body C22.8 (A105) GS-C25 (WCB) 13CrMo44 (F11) GS-17CrMo5-5 (WC6) TSTE 355 (LF2) GS-20Mn5 (LCB) X5CrNi18-9 (F304) GX5CrNi 18-9 (CF8) 2 Bonnet C22.8(A105) GS-C25 (WCB) 13CrMo44(F11) GS-17CrMo5-5 (WC6) TSTE 355 (LF2) GS-20Mn5 (LCB) X5CrNi18-9(F304) GX5CrNi 18-9 (CF8) X10Cr13(410)/ weld-on X10Cr13(410)/ weld-on X5CrNi18-9(F304)/ weld-on X5CrNi18-9(F304)/ weld-on X10Cr13 (410)+ weld-on X10Cr13 (410)+ weld-on X5CrNi18-9(F304)+ weld-on X5CrNi18-9(F304)+ weld-on 3 Disc 4 Seat 5 Stem 6 Sealing X10Cr13 (410) X5CrNi18-9(F304) Spiral-graphite/SS Spiral-graphite/PTFE/SS Graphite/PTFE Graphite/PTFE Graphite/PTFE Graphite/PTFE Packing 8 Bolt A193 B7 9 Nut A194 2H 10 Packing flange Hand Wheel X5CrNi18-9( F304) Spiral-graphite/SS 7 11 X10Cr13 (410) Spiral-graphite/SS C22.8(A105) Carbon steel A193 B7 A194 2H X15Cr13(F6) Carbon steel A182 L7 A194 8 X15Cr13(F6) Carbon steel A193 B7 A194 2H X5CrNi18-9(F304) Carbon steel Other material specification upon request ! "#$% &$'''&$% &$ Fig EDxx - Globe valves Outside screw & Yoke in cast steel - Robinets soupape en acier coulé à tige extérieure et arcade COBEPEX s.a. Belgium VALVE DIMENSIONS: Flanged Face-to-face dimensions: Flanges: Raised face: Design variants on request: Flanges design on request: EN 558 EN 1092-1 (DIN 2501/1972) EN 1092-1 – Form B1 (previously DIN 2526/1975 – Form C) ČSN 13 1160, DIN 2501, and other grooved or tongue EN 1092-1 Form C or Form D (previously DIN 2512/1975 – Form F or Form N), recessed or spigot EN 1092-1 – Form E or Form F (previously DIN 2513/1966 – Form V13 or Form R13), etc. Other flanges design variants on your request Butt - weld ends Weld ends Face-to-face dimensions: Weld ends: Groove form: On your request: EN 12982 – Line 64 (previously DIN 3202 – Line S2) DIN 3239 –Part 1 DIN 2559 – Sheet 1, Form 22 EN 12 627, and other Dk Dk Dk Dk ! "#$% &$'''&$% &$