material safety data sheet
Transcription
material safety data sheet
MATERIAL SAFETY DATA SHEET SECTION 1 — PRODUCT IDENTIFICATION AND USE PRODUCT IDENTIFIER R404A PRODUCT IDENTIFICATION NUMBER (PIN) : UN3337 Refrigerant PRODUCT USE MANUFACTURER'S NAME Alltemp Products Co. Ltd SUPPLIER’S NAME Alltemp Products Co. Ltd STREET ADDRESS 827 Brock Rd. South STREET ADDRESS 827 Brock Rd. South CITY Pickering PROVINCE Ontario CITY Pickering PROVINCE Ontario POSTAL CODE L1W 3J2 EMERGENCY TELEPHONE Canutec -1-613-996-6666 or *666 from a cellular phone POSTAL CODE L1W 3J2 EMERGENCY TELEPHONE NO. Canutec -1-613-996-6666 or *666 from a cellular phone SECTION 2 — HAZARDOUS INGREDIENTS HAZARDOUS INGREDIENTS % CAS NUMBER LD50 OF INGREDIENT (SPECIFY SPECIES AND ROUTE) LC50 OF INGREDIENT (SPECIFY SPECIES) 1,1,1-Trifluoroethane (HFC-143a) 52±1 420-46-2 N/A 540 g/m3/4h (rat) (NLM Dataset); Pentafluoroethane (HFC-125) 44±2 354-33-6 N/A 2735 g/m3/2h (mouse) (NLM Dataset); 1,1,1,2-Tetrafluoroethane (HFC-134a) 4±2 811-97-2 N/A 2910 g/m3/4h (rat) (NLM Dataset); SECTION 3 — PHYSICAL DATA PHYSICAL STATE Gas @ amb. ODOUR AND APPEARANCE Clear, colourless liquid and vapour – Slight ethereal odour ODOUR THRESHOLD (ppm) Not determined VAPOUR PRESSURE 8270 mm Hg at 20°C VAPOUR DENSITY (AIR=1) 3.42 approx EVAPORATION RATE (CC14=1): No Data Avail pH Not determined SPECIFIC GRAVITY (water=1) 1.06 g/cm3 @ 20°C COEFF. WATER/OIL DIST. Log pow = 1.740 (R143a, NLM Dataset); Log pow = 2.3 (R125); Log pow = 1.274 (R134a, HSDB). Insoluble in water; Soluble in: chlorinated solvents, alcohols, esters. BOILING POINT (ºC) -47.2°C to -46.4°C FREEZING POINT (ºC) Not determined SECTION 4 — FIRE AND EXPLOSION DATA FLAMMABILITY : This refrigerant is not flammable in air under ambient conditions of temperature and pressure. Certain mixtures of this refrigerant and air when under pressure may be flammable. Mixtures of this refrigerant and air under pressure should be avoided. Certain mixtures of HFCs and chlorine may be flammable or reactive under certain conditions. Thermal decomposition will evolve very toxic and corrosive vapours. (hydrogen fluoride) Containers may burst if overheated. MEANS OF EXTINCTION Use any Standard agent – choose the one most appropriate for the surrounding fire(material itself is not flammable) FLASH POINT (ºC) AND METHOD N/A UPPER FLAMMABLE LIMIT (% BY VOLUME) N/A AUTO IGNITION TEMPERATURE (ºC) <750°C HAZARDOUS COMBUSTION PRODUCTS N/A EXPLOSION DATA SENSITIVITY TO IMPACT : Not Determined LOWER FLAMMABLE LIMIT (% BY VOLUME) N/A SENSITIVITY TO STATIC DISCHARGE Not Determined SECTION 5 — REACTIVITY DATA CHEMICAL STABILITY : YES Stable under normal temperature conditions and recommended use INCOMPATIBILITY WITH OTHER SUBSTANCES : YES - Incompatible materials: finely divided metals, magnesium and alloys containing more than 2% magnesium. REACTIVITY, AND UNDER WHAT CONDITIONS : Avoid open flames and high temperatures. HAZARDOUS DECOMPOSITION PRODUCTS : hydrogen fluoride by thermal decomposition and hydrolysis. Halogens, halogen acids and possibly carbonyl halides. 57-404AMSDS PRODUCT IDENTIFIER R404A PRODUCT IDENTIFICATION NUMBER (PIN) : UN3337 SECTION 6 — TOXICOLOGICAL PROPERTIES ROUTE OF ENTRY : SKIN CONTACT EYE CONTACT INHALATION INGESTION EFFECTS OF ACUTE EXPOSURE TO PRODUCT Skin Contact: Liquid splashes or spray may cause freeze burns. Unlikely to be hazardous by skin absorption. Eye Contact: Liquid splashes or spray may cause freeze burns. Inhalation: To the best of our knowledge, the toxicological properties have not been thoroughly investigated. Ingestion:Ingestion is not considered a potential route of exposure. EFFECTS OF CHRONIC EXPOSURE TO PRODUCT : None known. EXPOSURE LIMITS 1,1,1,2-Tetrafluoroethane - 1000 ppm TWA (8hr) 1,1,1-Trifluoroethane - 1000 ppm TWA (8hr) Pentafluoroethane – 1000 ppm TWA (8hr) IRRITANCY OF PRODUCT SENSITIZATION TO PRODUCT CARCINOGENICITY N/A N/A N/A TERATOGENICITY: N/A REPRODUCTIVE TOXICITY : N/A MUTAGENICITY : N/A SYNERGISTIC PRODUCTS : N/A SECTION 7 — PREVENTIVE MEASURES PERSONAL PROTECTIVE EQUIPMENT GLOVES (SPECIFY) Leather Gloves RESPIRATOR (SPECIFY) Not normally required – For release into a confined space, where the concentration may be above the PEL of 1000 ppm, use a self contained, NIOSH-approved breathing apparatus or supplied air apparatus. EYE (SPECIFY) Sufficient eye protection should be worn. When handling compressed gas, at least glasses with side protection should be worn. When handling liquid gas, chemical safety goggles must be used as well as a protective shield. FOOTWEAR (SPECIFY) Use protective boots while handling gas cylinders CLOTHING (SPECIFY) General work clothing OTHER (SPECIFY) None under normal Conditions. ENGINEERING CONTROLS (SPECIFY, EG. VENTILATION, ENCLOSED PROCESS.) Use adequate general or local exhaust ventilation to keep airborne concentrations below the permissible exposure limits. LEAK AND SPILL PROCEDURE : Evacuate unprotected personnel. Protected personnel should remove ignition sources and shut off leak, if without risk, and provide ventilation. Unprotected personnel should not return until air has been tested and determined safe. Use water spray to keep fire-exposed container cool. WASTE DISPOSAL : Waste must be disposed of according to local, provincial and federal regulations HANDLING PROCEDURES AND EQUIPMENT : Eye washes and safety showers in the workplace are recommended. STORAGE REQUIREMENTS : Keep in a well ventilated place. Keep in a cool place away from fire risk, direct sunlight and all sources of heat such as electric and steam radiators. Avoid storing near to the intake of air conditioning units, boiler units and open drains. Cylinders and Drums: Keep container dry. Storage temperature: < 45°C SPECIAL SHIPPING INFORMATION : N/A Chemical Name ( UN # ) Liquefied gas.n.o.s., (Pentafluoroethane, Trifluoroethane, Tetrafluoroethane ) ( UN3337 ) Class Subclass Small Means of Containment Consumer Commodities 2.2 N/A N/A N/A SECTION 8 — FIRST AID MEASURES SPECIFIC MEASURES SKIN: Thaw affected areas with water. Remove contaminated clothing. Caution: clothing may adhere to the skin in the case of freeze burns. After contact with skin, wash immediately with plenty of warm water. If irritation or blistering occur obtain medical attention. EYES: Immediately irrigate with eyewash solution or clean water, holding the eyelids apart, for at least 10 minutes. Obtain immediate medical attention. INHALATION: Remove patient from exposure, keep warm and at rest. Administer oxygen if necessary. Apply artificial respiration if breathing has ceased or shows signs of failing. In the event of cardiac arrest apply external cardiac massage. Obtain immediate medical attention INGESTION: Ingestion is not considered a potential route of exposure. Do not induce vomiting. Provided the patient is conscious, wash out mouth with water and give 200-300 ml (half a pint) of water to drink. Obtain immediate medical attention. ADVICE TO PHYSICIAN: Adrenaline and similar sympathomimetic drugs should be avoided following exposure as cardiac arrhythmia may result with possible subsequent cardiac arrest. Treat symptomatically and supportively. Treatment may vary with condition of victim and specifics of incident. SECTION 9 — PREPARATION DATE OF MSDS PREPARED BY (GROUP, DEPARTMENT, ETC.) Health and Safety Department PHONE NUMBER 905-831-3311 DATE 05/02/2015 FICHE SIGNALÉTIQUE SECTION 1- IDENTIFICATION ET UTILISATION DU PRODUIT NOM DU PRODUIT UTILISATION DU PRODUIT R404A NUMÉRO D’IDENTIFICATION DU PRODUIT (NIP) : UN3337 Réfrigérant NOM DU MANUFACTURIER Alltemp Products Co. Ltd. NOM DU FOURNISSEUR Alltemp Products Co. Ltd. ADRESSE 827 Brock Road South ADRESSE 827 Brock Road South VILLE Pickering PROVINCE Ontario VILLE Pickering PROVINCE Ontario CODE POSTAL L1W 3J2 TÉLÉPHONE EN CAS D’URGENCE Canutec – 1-613-996-6666 ou *666 d’un téléphone cellulaire CODE POSTAL L1W 3J2 TÉLÉPHONE EN CAS D’URGENCE Canutec – 1-613-996-6666 ou *666 d’un téléphone cellulaire SECTION 2- INGRÉDIENTS DANGEREUX INGRÉDIENTS DANGEREUX % NUMÉRO CAS LD50 des ingrédients (spécifier espèce et entrée) LC50 des ingrédients (spécifier espèces) 1,1,1 – Trifluoroéthane (HFC-143a) 52±1 420-46-2 S/O 540 g/m3/4h (rat) (fichier NLM) Pentafluoroéthane (HFC-125) 44±2 354-33-6 S/O 2735 g/m3/2h (souris) (fichier NLM) 1,1,1,2 – Tetrafluoroéthane (HFC134a) 4±2 811-97-2 S/O 2910 g/m3/4h (rat) (fichier NLM) SECTION 3- PROPRIÉTÉS PHYSIQUES ÉTAT PHYSIQUE gazeux à température ambiante ODEUR ET APPARENCE Clair, vapeur et liquide incolores – Légère odeur d’éther SEUIL D’ODEUR (ppm) Non déterminé TENSION DE VAPEUR 8270 mm Hg à 20°C DENSITÉ DE VAPEUR (Air=1) 3,42 approx. DÉBIT D’ÉVAPORATION (CC14=1) S/O pH - Non déterminé POIDS SPÉCIFIQUE -1,06 g/cm3 à 20 °C CŒFFICIENT DE DIST. EAU/HUILE -1,740 (R143a, fichierNLM); LogP = 2,3 (R125); LogP = 1,275 (R134a, HSDB) Insoluble dans l’eau;soluble dans : solvants, alcools, esters. POINT D’ÉBULLITION (°C) -47,2oC à -46,4°C POINT DE CONGÉLATION (°C) Non déterminé SECTION 4- PROPRIÉTÉS D’INFLAMMABILITÉ ET EXPLOSION INFLAMMABILITÉ - Ce réfrigérant est ininflammable dans l’air sous des conditions ambiantes de température et pression. Certain mélange de ce réfrigérant avec l’air, lorsque sous pression, peuvent être inflammables. Il faut éviter les mélanges de ce réfrigérant avec l’air sous pression. Certains mélanges de HFC et de chlore peuvent être inflammables ou réactifs sous certaines conditions. La décomposition thermique produira des vapeurs très toxiques et corrosives. MOYENS D’EXTINCTION - Utiliser n’importe quel agent régulier – Choisir le moyen approprié pour les matériaux environnant (le produit lui-même n’est pas inflammable) POINT D’ÉCLAIR (°C) ET MÉTHODE N/D LIMITE SUPÉRIEURE D’INFLAMMABILITÉ (% par volume) N/D S/O TEMPÉRATURE DE COMBUSTION SPONTANÉE (°C) <750°C PRODUITS DE COMBUSTION DANGEREUX S/O PROPRIÉTÉS EXPOLSIVES Non déterminé SENSIBILITÉ À L’IMPACT Non déterminé LIMITE INFÉRIEURE D’INFLAMMABILITÉ (% par volume) N/D SENSIBILITÉ AUX CHARGES STATIQUES Non déterminé SECTION 5- PROPRIÉTÉS DE RÉACTIVITÉ STABILITÉ CHIMIQUE : Oui, Stable sous des conditions normales de température et usage recommandé. INCOMPATIBILITÉ AVEC D’AUTRES SUBSTANCES : Oui – matières incompatibles : métaux très fins, magnésium et alliages contenant plus de 2% de magnésium. RÉACTIVITÉ ET SOUS QUELLES CONDITIONS : Éviter les flammes nues et les hautes températures PRODUITS DE DÉCOMPOSITIONS DANGEREUX : fluorure d’hydrogène par décomposition thermique et hydrolyse. Halogènes, acides halogènes et possiblement les halogénures de carbonyle. 57-404AMSDS NOM DU PRODUIT R404A NUMÉRO D’IDENTIFICATION DU PRODUIT (NIP) : UN3337 SECTION 6 - PROPRIÉTÉS TOXICOLOGIQUES VOIX DE PÉNÉTRATION : CONTACT AVEC LA PEAU CONTACT AVEC LES YEUX INHALATION INGESTION EFFETS D’UNE BRÈVE EXPOSITION AU PRODUIT: Contact avec la peau : Les éclaboussures de liquide ou vaporisation peuvent causer des brûlures par le froid. Les dangers d’absorption par la peau sont peu probables. Contact avec les yeux : Les éclaboussures de liquide ou vaporisation peuvent causer des brûlures par le froid. Inhalation : Au meilleur de notre connaissance, Il n’y a pas eu d’étude toxicologique complète. Ingestion : l’ingestion n’est pas une voie d’entrée probable. EFFETS D’UNE EXPOSITION À LONG TERME AU PRODUIT : Aucun effet connu LIMITE D’EXPOSITION : 1,1,1,2-Tétrafluoroéthane – 1000ppm TWA (8h) 1,1,1- Trifluoroéthane – 1000ppm TWA (8h) Pentafluoroéthane – 1000ppm TWA (8h) IRRITABILITÉ AU PRODUIT : N/D SENSIBILISATION AU PRODUIT : N/D CANCÉROGÉNICITÉ : N/D TÉRATOGÉNICITÉ N/D TOXICITÉ POUR LA REPRODUCTION: N/D MUTATION GENETIQUE N/D PRODUITS SYNERGIQUES N/D SECTION 7 - MESURES PRÉVENTIVES ÉQUIPEMENTS DE PROTECTION PERSONNELS GANTS (SPÉCIFIER) Gants de cuir RESPIRATEUR (SPÉCIFIER) : Normalement non requis – Si relâché dans un espace confiné, où la concentration peut dépasser le PEL de 1000 ppm, utiliser un respirateur autonome, approuvé NIOSH ou un appareil d’alimentation d’air. YEUX (SPÉCIFIER) Portez une protection oculaire suffisante. Pour la manipulation de cylindre de gaz comprimé il faut porter au moins des lunettes avec protection latérale. Pour la manipulation de gaz liquide, il faut porter des lunettes de protection chimique ainsi qu’un écran facial. CHAUSSURES (SPÉCIFIER) Bottes de protection pour la manipulation des cylindres VÊTEMENTS (SPÉCIFIER) Vêtements de travail généraux AUTRE (SPÉCIFIER) : Aucun, sous des conditions normales CONTRÔLES D’INGÉNIERIE (SPÉCIFIER, EX. : VENTILATION, PROCÉDÉ EN ESPACE CLOS) : Utiliser une ventilation d’évacuation générale ou locale adéquate pour maintenir la concentration dans l’air à un niveau inférieur à la limite d’exposition. PROCÉDURES EN CAS DE FUITE OU DÉVERSEMENT : Évacuer le personnel non protégé. Le personnel protégé doit retirer ou éteindre les sources de combustion ou d’ignition, et colmater la fuite, s’il peut le faire sans risque, et fournir de la ventilation. Les personnes non protégées ne doivent par retourner sur les lieux avant que l’air ait été testé et considéré sécuritaire. Vaporiser avec de l’eau les contenants exposés au feu pour les garder frais. ÉLIMINATION DES DÉCHETS : Conformez-vous à la réglementation fédérale, provinciale et locale. PROCÉDURE DE MANUTENTION ET ÉQUIPEMENT : Il est recommandé d’avoir des douches oculaires et des douches de sécurité sur les lieux de travail. CONDITIONS D’ENTREPOSAGE : Garder dans un endroit bien aéré. Garder dans un endroit frais, loin des risques d’incendie, de la lumière directe du soleil et de toute source de chaleur, tel que les radiateurs électrique et à vapeur. Éviter d’entreposer près des prises d’air des appareils de climatisation, chaudières, bouilloires et drains ouverts. Cylindres et barils : Garder les contenants au sec. Température d’entreposage : <45 oC. PRÉCAUTIONS SPÉCIALES D’EXPÉDITION - IS/O Nom Chimique (# UN) (Pentafluoroéthane, Trifluoroéthane, Tetrafluoroéthane) (UN3337) Classe Sous-classe Petits moyens de confinement Produit de consommation 2.2 N/D N/D N/D SECTION 8- PREMIERS SOINS MESURES SPÉCIFIQUES PEAU : Réchauffer la zone graduellement en rinçant avec de l’eau. Enlever les vêtements contaminés. Attention : les vêtements peuvent coller à la peau. Après un contact avec la peau, laver immédiatement avec beaucoup d’eau tiède. S’il y a irritation ou des cloques pendant plus de 10 min. Consulter un médecin. YEUX : Rincer immédiatement avec une solution oculaire ou de l’eau propre en maintenant les paupières ouvertes. Consulter immédiatement un médecin. INHALATION : Amener immédiatement la personne à l’air frais, gardez-la au chaud et au repos. Administrer de l’oxygène si nécessaire. Donner la respiration artificielle, si la personne cesse de respirer ou montre des signes de faiblesse. Dans l’Éventualité d’un arrêt cardiaque, faire un massage cardiaque externe. Consulter immédiatement un médecin. INGESTION : L’ingestion est peu probable. Ne pas faire vomir. Si le patient est conscient, lui faire rincer la bouche et faire boire de 200 à 300 ml d’eau. Consulter immédiatement un médecin. AVIS AU MÉDECIN : L’adrénaline et les médicaments sympathomimétiques doivent être évités suite à une exposition, de l’arythmie cardiaque pourrait se produire ainsi qu’un arrêt cardiaque subséquent. Faire un traitement de soutien et traitez les symptômes. Le traitement peut varier selon l’état de la victime et les circonstances spécifiques de l’incident. SECTION 9- PRÉPARATION DE LA FICHE SIGNALÉTIQUE PRÉPARÉE PAR (GROUPE DÉPARTEMENT ETC.) Département de la santé et sécurité NO DE TÉLÉPHONE 905-831-3311 DATE 05/02/2015