Band wall sconce - Installation Instructions

Band wall sconce - Installation Instructions
Page 1 of 2
Model BA-
Please read all instructions prior to installation and keep for future reference!
1.
2.
Product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved. Ce produit
3.
doit être installé selon le code d’installation pertinent, par une
personne qui connaît bien les produit et son fonctionnement ainsi
que les risques inhérents.
4.
Product is suitable for wall mount indoor and outdoor locations.
For wet location applications, product must be installed 48”
above ground.
This product mounts horizontally to a single gang junction box or
a 4” square junction box when used with included canopy cover.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
Prior to installation ensure power is off at fuse box to prevent
electrical shock.
1
Remove the back plate of the
Band light fixture by removing
4 flat head screws.
2
threaded
pipe
crossbar
nut
ground
screw
back
plate
Then remove back plate
and ground screw and set
back plate aside.
crossbar assembly
Put together crossbar assembly composed of threaded pipe,
crossbar, and nut.
3
Feed the hot (black) and neutral (white) power
wires through the threaded pipe in the crossbar
assembly. Ensure crossbar assembly is grounded
in accordance with local electrical codes. Mount
and secure the crossbar assembly to the electrical
junction box with provided 8-32 screws.
crossbar assembly
8-32 screw
4
back
plate
gasket
washer
canopy
cover
crossbar
assembly
gasket
washer
tooth
locking
washer
nut
Slide the canopy cover onto the crossbar assembly threaded pipe. Then place gasket washer over the crossbar
assembly threaded pipe. Next slide back plate onto the crossbar assembly, place second gasket washer, external
tooth locking washer, nut, and securely tighten. Ensure canopy cover and back plate are positioned level.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
REV2.1
Band wall sconce - Installation Instructions
Page 2 of 2
Model BA-
Please read all instructions prior to installation and keep for future reference!
1.
2.
Product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved. Ce produit
3.
doit être installé selon le code d’installation pertinent, par une
personne qui connaît bien les produit et son fonctionnement ainsi
que les risques inhérents.
4.
Product is suitable for wall mount indoor and outdoor locations.
For wet location applications, product must be installed 48”
above ground.
This product mounts horizontally to a single gang junction box or
a 4” square junction box when used with included canopy cover.
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
Prior to installation ensure power is off at fuse box to prevent
electrical shock.
5
Connect the load (black) power wire to the load (blue)
input wire on LED driver with wire nut. Connect the
neutral (white) power wire to the neutral (brown) input
wire on LED driver with wire nut. Screw ground wire to
back plate. Ensure connections are secure and place
LED driver and all wire nut connections inside Band light
fixture body.
120 VAC load (black)
120 VAC input load (blue)
120 VAC input neutral (brown)
120 VAC neutral (white)
6
Ensure clear silicone back plate gasket is seated properly
on back plate. Slide the Band light fixture body onto
the back plate. Make sure the 4 mounting screws have
installed silicone O-rings and secure Band light fixture
body to back plate.
clear silicone
back plate
gasket
7
For installation in wet locations, caulk
around the complete perimeter of the
canopy cover with waterproof sealant.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
REV2.1