LSHT Torqmotors™ and Nichols™ Motors
Transcription
LSHT Torqmotors™ and Nichols™ Motors
LSHT Torqmotors™ and Nichols™ Motors Catalog No. HY13-1590-005/US,EU LSHT Torqmotors™ and Nichols™ Motors Parker Hannifin Corporation Hydraulic Pump/Motor Division 2745 Snapps Ferry Road Greeneville, TN 37745 USA Tel: (423) 639-8151 Fax: (423) 787-2418 www.parker.com/pumpmotor HY13-1590-005/US,EU © Copyright 2006 Parker Hannifin Corporation All rights reserved. Parker Hannifin Corporation 6035 Parkland Blvd. Cleveland, Ohio 44124-4141 Telephone: (216) 896-3000 Fax: (216) 896-4000 www.parker.com About Parker Hannifin Corporation Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 500 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that control motion in some 1,000 industrial and aerospace markets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic, and electromechanical motion-control solutions. Our Company has the largest distribution network in its field, with over 7,500 distributors serving nearly 400,000 customers worldwide. WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. Offer of Sale The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated on the separate page of this document entitled “Offer of Sale”. © 2000, 2001, 2003, 2004, 2006 Parker Hannifin Corporation Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Parker Hannifin Corporation Parker’s Charter To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve profitable growth through premier customer service. Product Information North American customers seeking product information, the location of a nearby distributor, or repair services will receive prompt attention by calling the Parker Product Information Center at our toll-free number: 1-800-C-PARKER (1-800-272-7537). In Europe, call 00800-C-PARKER-H (00800-2727-5374). The Aerospace Group is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high-technology markets, while achieving growth through premier customer service. The Climate & Industrial Controls Group designs, manufactures and markets systemcontrol and fluid-handling components and systems to refrigeration, air-conditioning and industrial customers worldwide. The Fluid Connectors Group designs, manufactures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems. The Seal Group designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction. The Hydraulics Group designs, produces and markets a full spectrum of hydraulic components and systems to builders and users of industrial and mobile machinery and equipment. The Filtration Group designs, manufactures and markets quality filtration and clarification products, providing customers with the best value, quality, technical support, and global availability. The Automation Group is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide. The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical flow components for worldwide process instrumentation, ultra-highpurity, medical and analytical applications. LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Wherever in the world machinery is designed, manufactured, or used, Parker is there to meet your hydraulic application requirements–with complete hydraulic component selection, worldwide availability, and technical assistance. signers, builders, and users of motion control machinery. No more shuffling through dozens of separate catalogs from dozens of separate suppliers. And when you’re ready to order, call your local Parker hydraulic distributor for fast delivery and service. Or call your Parker Hydraulic Sales Office (see listing at the back of this catalog). This catalog contains the information you need to order hydraulic motor products. It contains complete specifications, dimensions, and ordering information on the complete line of Parker hydraulic motor products, including technical data and reference material for de- In line with our policy of continuing product improvement, specifications and information contained in this catalog are subject to change. Copyright © 2000, 2001, 2003, 2004 and 2006 by Parker Hannifin Corporation. All rights reserved. PRINTED IN THE U.S.A. 000 Intro & TOC.indd, js 3 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Contents LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Product Overview Low Speed High Torque Torqmotor™ Series TC Series ..................................................................................................................................................... 6 - 19 TB Series ................................................................................................................................................... 20 - 35 TS Series ................................................................................................................................................... 36 - 45 TE Series ................................................................................................................................................... 46 - 63 Small Frame Options.................................................................................................................................. 64 - 69 TJ Series .................................................................................................................................................... 70 - 81 Medium Frame Options .............................................................................................................................. 82 - 83 TF Series.................................................................................................................................................... 84 - 99 TF Clutch Series .................................................................................................................................... 100 - 103 DF Series ............................................................................................................................................... 104 - 109 TL Series ................................................................................................................................................ 110 - 119 TG Series ............................................................................................................................................... 120 - 135 BG Series ............................................................................................................................................... 136 - 143 DG Series............................................................................................................................................... 144 - 149 TH Series ............................................................................................................................................... 150 - 163 BH Series ............................................................................................................................................... 164 - 169 TK Series ............................................................................................................................................... 170 - 180 Large Frame Options ............................................................................................................................. 181 - 187 Installation/Operation Data ..................................................................................................................... 188 - 191 Low Speed High Torque Nichols™ Motors Series 110A Series............................................................................................................................................ 192 - 205 700 Series .............................................................................................................................................. 206 - 219 716 Series .............................................................................................................................................. 220 - 230 Nichols™ Options .................................................................................................................................. 231 - 234 Installation/Operation Data ...............................................................................................................................235 Engineering Data for Torqmotor™ and .................................................................................................... 236 - 240 Nichols™ Motor High Speed Hydraulic Motor .................................................................................................................... 241 - 251 Offer of Sale .........................................................................................................................................................253 000 Intro & TOC.indd, js 4 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 000 Intro & TOC.indd, js 5 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information / Technische Information / Segni / Informacion Tecnica 15 Displacements 15 Schluckvolumen 15 Cylindrée 15 Despazamientos Maximum Pressure Max. Druckgefalle Chaute de pression max. Presion Maxima (2.2 - 24.0 in3/rev) 36 . . . 390 cm3/rev High Performance and long life in a reduced space volume fluid flow continually washes across splines Cont (to1250 psi) . . .86 bar Int (to 1750 psi) . . .121 bar and seals to extend their life. Roller vanes and sealed commutation assure high volumetric efficiency and smooth low speed operation. (to 15 gpm) . . . 57 lpm Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Side Load Seitenlast Charges latèrales Carga Maxima Lateral Big Performance In A Small Package envelope describe Parker’s TC Series motors. High Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Torque Max Drehmoment Couple Maxi Torque Maximo LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série (902 rpm) 902 rpm Cont (1905 lb in) 215.2 Nm Int (2709 lb in) 306.1 Nm (to 788 lb) . . . 3505 N 001 TC.indd, js 6 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l De ndré luck acem sp e v olu ent az am me Ma i n en x. t o s Ma pe s e x Vit . Dre d @ es hz Ma Ve se d ahl x. i loc e r Inte nte r i o Ma dad m tatio rmitt mitte i x. n ax m eren nt flo Ma oil i de x. flow ma a axi rB w Dé Sch ca etr bit u lu ie b da Ca d´h cks l in : t ud r u t erm al ile m om M it e Ma ax ax nte x im i od ma Ma . Diff eA x im e re x. ce Ch Dru nti o it e ute ck al P ge Pr r d e e s e p f ä ll s s ure ion re e Ma dif ssio x. e n r en m Ma sup c ia a x i x p lm Pr . Ein ly pr ax es ga e im Pr sion ngs ssur a es e d m ion ax ruck i ma en Ma x im t ré x ad e Ma . torq ea x. u lim e Co Dre en up hm tac To le m om ion rqu e a nt e M xi ax Ma im x o Ma . per for x. L m Pu is eist anc Ma sanc unga e xim e d bg o r e s abe Mi ed ort n. inm ie Mi star ien max n. t in to i g Co Anl t up au orq u f l To e m mo e rqu m e m in. fo ent ini urn mo i a de u dé a rr m an anr qu e age LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série Motor Series TC cm3/rev in3/rev rev/min cont / int* l/min g/min cont / int* bar psi max bar psi cont / int* Nm lb-in TC 0036 36 2.2 902 34 9 34 9 86 1250 TC 0045 41 2.5 794 34 9 34 9 TC 0050 49 3.0 688 34 9 TC 0065 65 4.0 517 TC 0080 82 5.0 TC 0100 121 1750 134 1950 31 272 44 393 4.2 5.6 16 138 27 236 86 1250 121 1750 134 1950 40 351 56 496 4.5 6.1 20 174 33 295 34 9 86 1250 121 1750 134 1950 48 423 67 589 4.7 6.3 27 235 39 349 34 9 34 9 86 1250 121 1750 134 1950 66 582 92 810 4.8 6.5 41 361 67 590 413 34 9 34 9 86 1250 121 1750 134 1950 96 753 119 1050 4.9 6.6 61 539 86 758 98 6.0 460 45 12 45 12 86 1250 121 1750 134 1950 100 888 140 1240 6.1 8.2 78 691 106 934 TC 0130 130 8.0 429 45 12 57 15 86 1250 121 1750 134 1950 138 1218 192 1697 7.5 10.1 111 986 169 1492 TC 0165 163 10.0 346 45 12 57 15 86 1250 121 1750 134 1950 173 1529 238 2110 7.5 10.0 139 1232 209 1846 TC 0195 195 11.9 287 45 12 57 15 86 1250 121 1750 134 1950 205 1815 286 2532 7.3 9.8 195 1724 264 2332 TC 0230 228 13.9 246 45 12 57 15 76 1100 107 1550 134 1950 215 1905 298 2637 6.3 8.4 195 1722 261 2310 TC 0260 260 15.9 217 45 12 57 15 66 950 97 1400 134 1950 211 1870 306 2709 5.4 7.3 183 1618 265 2344 TC 0295 293 17.9 193 45 12 57 15 59 850 86 1250 134 1950 208 1843 300 2657 4.7 6.3 189 1675 269 2379 TC 0330 328 20.0 173 45 12 57 15 52 750 76 1100 134 1950 206 1819 296 2621 4.0 5.3 187 1655 262 2318 TC 0365 370 22.6 152 45 12 57 15 45 650 66 950 134 1950 206 1825 296 2622 3.4 4.6 186 1648 276 2443 TC 0390 392 24.0 144 45 12 57 15 45 650 66 950 134 1950 207 1832 296 2622 3.2 4.3 192 1698 286 2527 Performance data based on testing using 10W40 oil with a viscosity of 43,1 cSt. (200 SUS) at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. max KW HP cont / int* Nm lb-in * Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 001 TC.indd, js 7 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TC Series Code XXXX X X XX 0 XXXX Displacement Schluckvolumen Cylindrée Desplazamiento Mounting/Ports Gehäuse/Anschluß Carter/Plan de raccordement Montaje/Lumbreras Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion Options Opciones cm3/U cm3/tr cm3/giro cu in3/rev 0036 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série 36 41 49 65 82 98 130 163 195 228 260 293 328 370 392 / / / / / / / / / / / / / / / 2.2 2.5 3.0 4.0 5.0 6.0 8.0 10.0 11.9 13.9 15.9 17.9 20.0 22.6 24.0 Code Code Mounting/Ports SAE "A" 2 Bolt, 5/16-18 UNC Manifold 0 Rotation Standard AM SAE "A" 2 Bolt, 1/2-14 NPTF AP Code Shaft 1" Keyed SAE "A" 2 Bolt,7/8-14 SAE 10 AS 1" 6B Spline 4 Bolt w/3/8-16 Thd, 5/16-18 UNC Manifold 11 FM Long 1" Keyed 13 4 Bolt w/3/8-16 Thd,1/2-14 NPTF FP 4 Bolt w/3/8-16 Thd, 7/8-14 SAE Code AAAB FS AAAA Options No Paint No lackiert Black Paint Schwarz lackiert For other available options, see pages 64-69. 001 TC.indd, js 8 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos TC 0036 2 5 10 US Schluckstrom [L/min] 20 25 15 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série 30 34 0.5 1 500 50 2 3 Flow [G/min] 5 4 7 9 120 40 400 1500 300 85 bar 70 20 1250 200 psi 30 1750 Torque [lb/in] Drehmoment [Nm] 100 1000 50 750 10 100 35 500 0 0 100 200 300 400 500 600 Drehzahl [1/min] TC 0045 2 5 60 700 800 900 0 1000 0 100 200 300 400 500 600 Speed [Rpm] 15 20 800 900 1000 US Schluckstrom [L/min] 10 700 25 30 Flow [G/min] 34 0.5 1 120 50 2 4 3 5 7 9 500 1750 400 40 1500 85 bar 70 20 50 1250 300 1000 psi 30 Torque [lb in] Drehmoment [Nm] 100 200 750 10 35 100 0 100 200 300 400 500 600 700 0 800 0 100 200 300 Drehzahl [1/min] TC 0050 2 5 10 400 Speed [Rpm] 500 600 700 800 Schluckstrom [L/min] 15 20 25 30 Flow [G/min] 34 70 600 60 120 50 100 0.5 1 2 3 4 5 US 7 9 1750 1500 400 1250 300 1000 200 750 100 500 85 40 70 bar 30 50 20 Torque [lb in] Drehmoment [Nm] 500 35 10 0 0 100 200 300 400 500 600 0 700 0 Drehzahl [1/min] Cont. psi 0 500 100 200 300 400 500 600 700 Speed [Rpm] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 001 TC.indd, js 9 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos TC 0065 100 2 5 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série Schluckstrom [L/min] 10 15 20 25 30 34 0.5 1 2 3 Flow [G/min] 5 4 US 7 9 800 1750 120 700 100 600 85 500 1500 1250 bar 70 40 1000 400 psi 60 Torque [lb in] Drehmoment [Nm] 80 300 750 50 200 20 500 35 100 0 0 0 50 100 150 200 250 300 350 400 450 500 0 550 50 100 150 200 TC 0080 2 5 15 20 300 350 400 450 500 550 25 US Flow [G/min] Schluckstrom [L/min] 10 250 Speed [Rpm] Drehzahl [1/min] 30 0.5 1 34 3 2 4 5 12 9 120 120 1000 100 800 1750 1250 85 70 40 50 bar 60 600 1000 400 750 500 200 35 20 1500 psi 80 Torque [lb in] Drehmoment [Nm] 100 0 0 0 50 100 150 200 250 300 Drehzahl [1/min] 350 400 0 450 50 100 150 200 250 300 350 400 450 Speed [Rpm] TC0100 Schluckstrom [L/min] 25 10 15 20 25 30 34 45 0.5 1 2 140 4 5 Flow [G/min] 7 US 9 12 1200 1750 120 120 1000 100 800 1500 100 70 60 40 bar 85 1250 600 1000 400 750 50 20 35 psi 80 Torque [lb in] Drehmoment [Nm] 3 200 500 0 0 0 50 100 150 200 250 300 350 400 450 0 500 Cont. 50 100 150 200 250 300 350 400 450 500 Speed [Rpm] Drehzahl [1/min] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 001 TC.indd, js 10 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série TC 0130 2 5 10 15 20 25 30 34 45 0.5 1 2 57 3 5 4 US Flow [G/min] 9 7 Schluckstrom [L/min] 15 12 200 1600 1400 1200 1500 85 70 50 1000 1250 800 1000 600 50 400 35 200 0 psi 100 Torque [lb in] 100 bar Drehmoment [Nm] 1750 120 150 750 500 0 0 50 100 150 200 250 300 350 400 450 0 50 100 150 Drehzahl [1/min] TC0165 2 5 Schluckstrom [L/min] 10 15 20 25 200 250 300 350 400 450 Speed [Rpm] 30 US Flow [G/min] 40 45 57 0.5 1 2 3 4 5 9 7 12 15 250 2100 1800 200 1750 1500 100 70 1250 psi 1200 85 100 Torque [lb in] 1500 150 bar Drehmoment [Nm] 120 900 1000 600 50 750 50 300 35 500 0 0 50 100 150 200 Drehzahl [1/min] 250 300 0 350 0 50 100 150 200 250 300 350 Speed [Rpm] TC0195 US Schluckstrom [L/min] 25 10 15 20 25 30 40 Flow [G/min] 45 57 0.5 1 2 300 3 4 7 5 9 12 15 2500 2250 250 70 100 1500 1500 1250 1250 1000 psi 85 Torque [lb in] 100 150 1750 1750 bar Drehmoment [Nm] 2000 120 200 1000 750 50 50 500 35 250 0 0 50 100 150 200 250 500 0 300 0 Drehzahl [1/min] Cont. 750 50 100 150 200 250 300 Speed [Rpm] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 001 TC.indd, js 11 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série TC 0230 2 5 10 15 20 25 30 US Flow [G/min] Schluckstrom [L/min] 40 45 0.5 1 2 57 3 4 7 5 9 12 15 300 2500 250 1550 1500 75 1100 psi 1300 Torque [lb in] 90 150 bar Drehmoment [Nm] 2000 105 200 1000 100 750 50 500 50 500 35 0 0 0 50 100 150 Drehzahl [1/min] 200 0 250 25 50 75 100 125 150 175 200 225 250 Speed [Rpm] TC 0260 US Schluckstrom [L/min] 2 5 10 15 20 25 30 Flow [G/min] 40 45 0.5 1 57 300 2 3 5 4 9 7 15 12 2500 2000 1400 95 Torque [lb in] 200 80 psi bar 65 1200 1500 150 950 1000 100 750 50 500 50 35 500 0 0 50 100 150 0 200 0 25 50 75 Drehzahl [1/min] 100 125 Speed [Rpm] 150 175 200 225 TC 0295 US Schluckstrom [L/min] 300 2 5 10 15 20 25 30 40 45 57 0.5 1 2 3 4 5 Flow [G/min] 7 9 12 15 2500 250 2000 150 70 60 1250 100 50 20 40 60 80 100 120 140 160 180 850 1000 500 0 200 0 Drehzahl [1/min] Cont. 1000 500 35 0 0 1500 psi 85 Torque [lb in] 200 bar Drehmoment [Nm] Drehmoment [Nm] 250 20 40 60 80 100 120 140 160 180 200 Speed [Rpm] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 001 TC.indd, js 12 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série TC 0330 Schluckstrom [L/min] 2 300 5 10 15 20 25 30 US Flow [G/min] 40 45 0.5 1 57 3 2 4 7 5 9 12 15 2500 250 1100 Torque [lb in] 75 100 50 50 1500 psi 150 bar Drehmoment [Nm] 2000 200 1000 500 35 0 20 40 60 80 100 120 140 500 20 180 0 160 750 250 180 0 0 20 40 60 80 Drehzahl [1/min] 100 120 140 160 Speed [Rpm] TC 0365 US Flow [G/min] Schluckstrom [L/min] 2 5 10 15 20 25 30 40 45 0.5 1 57 300 3 2 4 5 7 9 12 15 2500 250 950 150 45 1500 psi Torque [lb in] 65 200 bar Drehmoment [Nm] 2000 650 1000 100 35 500 500 50 0 20 40 60 80 100 120 0 0 20 160 0 140 20 40 60 80 Speed [Rpm] Drehzahl [1/min] 100 120 250 160 140 TC 0390 US Schluckstrom [L/min] 2 5 10 15 20 25 30 40 50 57 0.5 1 300 2 3 4 5 12 15 2500 250 2000 200 150 100 45 50 35 0 0 25 50 75 100 125 1000 650 500 20 150 500 0 0 25 50 75 100 125 250 150 Speed [Rpm] Drehzahl [1/min] Cont. 950 1500 psi Torque [lb in] 65 bar Drehmoment [Nm] Flow [G/min] 9 7 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 001 TC.indd, js 13 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shaft Side Load Capacity N (lb) Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série 4448 (1000) 4003 (900) 3558 (800) 3113 (700) 2669 (600) 2224 (500) 1779 (400) 0.0 100.0 200.0 300.0 400.0 500.0 600.0 700.0 800.0 Speed (RPM) 12.7 (0.5 In.) 25.4 (1.0 In.) 38.1 (1.5 In.) 50.8 (2.0 In.) The allowable side load curve is based on bushing life of 2.5 x 106 revolutions. Die zulaessige radiale Wellenbelastung bezieht sich auf die Lager-Lebensdauer 2,5 x 106 Umdrehungen. L’effort radial admissible sur l’arbre depend a une duree de vie 2,5 x 106 de rotation. La curva de carga lateral admisible se basa en vida util de cojinete de 2.5 x 10 revoluciones. 12.7 (.5) 25.4 (1.0) 38.1 (1.5) English equivalents for metric specifications are shown in ( ). 001 TC.indd, js 14 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras Code: AM “L” 32.3 (1.27) SAE "A" 2 Bolt, 5/16-18 UNC Manifold ø 95.5 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série 2.55 (.10) 48.26 (1.900) 14.2 (.56) 63.50 (2.500) A A (3.76) Max ø 82.50/82.55 (3.248/3.250) A B 4 x 5/16-18 UNC 12.7 (.50) A 127.3 (5.01) B 45.7 (1.8) 2 x 31.75 (1.250) 13.49 (.531) ø 106.38 (4.188) 28.56 (1.125) 2 x 14.28 (.562) A--A 1.9 (0.075) O-Ring Ø17.6 (0.695) Motor with manifold mount is supplied with 2 O-rings. Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni è corredato da 2 OR. Code AM disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 5.46 5.54 5.67 5.81 5.88 6.19 6.45 6.74 6.93 7.23 7.39 7.71 8.09 8.21 Poids/Peso (lb) (12.0) (12.2) (12.5) (12.8) (13.0) (13.6) (14.2) (14.9) (15.3) (15.9) (16.3) (17.0) (17.8) (18.1) Length "L" mm 120.1 121.6 124.8 127.9 131.1 137.5 143.8 150.2 156.5 162.9 169.2 175.6 184.2 188.3 "L" (in) (4.73) (4.79) (4.91) (5.04) (5.16) (5.41) (5.66) (5.91) (6.16) (6.41) (6.66) (6.91) (7.25) (7.41) Code: AP SAE "A" 2 Bolt, 1/2-14 NPTF “L” 32.3 (1.27) 2.55 (.10) 14.2 (.56) 48.26 (1.900) 45.72 (1.800) A A ø 95.5 (3.76) Max ø 82.50/82.55 (3.248/3.250) 127.3 (5.01) B B 2 x 22.86 (.900) 1/2-14 NPTF 13.49 (.531) ø 106.38 (4.188) Code AP disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 5.46 5.54 5.67 5.81 5.88 6.19 6.45 6.74 6.93 7.23 7.39 7.71 8.09 8.21 Poids/Peso (lb) (12.0) (12.2) (12.5) (12.8) (13.0) (13.6) (14.2) (14.9) (15.3) (15.9) (16.3) (17.0) (17.8) (18.1) Length "L" mm 120.1 121.6 124.8 127.9 131.1 137.5 143.8 150.2 156.5 162.9 169.2 175.6 184.2 188.3 "L" (in) (4.73) (4.79) (4.91) (5.04) (5.16) (5.41) (5.66) (5.91) (6.16) (6.41) (6.66) (6.91) (7.25) (7.41) English equivalents for metric specifications are shown in ( ). 001 TC.indd, js 15 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série Code: AS SAE "A" 2 Bolt, 7/8-14 SAE “L” 32.3 (1.27) 2.55 (.10) 48.26 (1.900) 14.2 (.56) 45.72 (1.800) A A ø 95.5 (3.76) Max ø 82.50/82.55 (3.248/3.250) 127.3 (5.01) B B 13.49 (.531) 2 x 22.86 (.900) 7/8-14 SAE O-Ring ø 106.38 (4.188) Code AS disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 5.46 5.54 5.67 5.81 5.88 6.19 6.45 6.74 6.93 7.23 7.39 7.71 8.09 8.21 Poids/Peso (lb) (12.0) (12.2) (12.5) (12.8) (13.0) (13.6) (14.2) (14.9) (15.3) (15.9) (16.3) (17.0) (17.8) (18.1) Length "L" mm 120.1 121.6 124.8 127.9 131.1 137.5 143.8 150.2 156.5 162.9 169.2 175.6 184.2 188.3 "L" (in) (4.73) (4.79) (4.91) (5.04) (5.16) (5.41) (5.66) (5.91) (6.16) (6.41) (6.66) (6.91) (7.25) (7.41) Code: FM 4 Bolt w/3/8-16 Thd, 5/16-18 UNC Manifold "L" 32.3 (1.27) A ø 95.5 (3.76) Max A--A O-Ring 1.9 (0.075) Ø17.6 (0.695) 4 x 5/16-18 UNC 12.7 (.50) 48.26 (1.900) 2.55 (.10) 63.50 (2.500) 45˚ A A B A 80.0 (3.118) ø 44.40/44.45 (1.748/1.750) B 2 x 31.75 (1.250) 2 x 14.28 (.562) 28.56 (1.125) 45.7 (1.8) ø 82.55 (3.250) 3/8-16 UNC Motor with manifold mount is supplied with 2 O-rings. Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni è corredato da 2 OR. Code FM disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 7.58 7.80 8.07 8.35 8.66 8.80 Poids/Peso (lb) (13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5) (16.2) (16.7) (17.2) (17.8) (18.4) (19.1) (19.4) Length "L" mm 120.1 121.6 124.8 127.9 131.1 137.5 143.8 150.2 156.5 162.9 169.2 175.6 184.2 188.3 "L" (in) (4.73) (4.79) (4.91) (5.04) (5.16) (5.41) (5.66) (5.91) (6.16) (6.41) (6.66) (6.91) (7.25) (7.41) English equivalents for metric specifications are shown in ( ). 001 TC.indd, js 16 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série Code: FP 4 Bolt w/3/8-16 Thd, 1/2-14 NPTF "L" 32.3 (1.27) 48.26 (1.900) 2.55 (.10) 45˚ 45.72 (1.800) A ø 95.5 (3.76) Max A 80.0 (3.118) ø 44.40/44.45 (1.748/1.750) B B 2 x 22.86 (.900) ø 82.55 (3.250) 1/2-14 NPTF 3/8-16 UNC Code FP disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 7.58 7.80 8.07 8.35 8.66 8.80 Poids/Peso (lb) (13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5) (16.2) (16.7) (17.2) (17.8) (18.4) (19.1) (19.4) Length "L" mm 120.1 121.6 124.8 127.9 131.1 137.5 143.8 150.2 156.5 162.9 169.2 175.6 184.2 188.3 "L" (in) (4.73) (4.79) (4.91) (5.04) (5.16) (5.41) (5.66) (5.91) (6.16) (6.41) (6.66) (6.91) (7.25) (7.41) Code: FS 4 Bolt w/3/8-16 Thd, 7/8-14 SAE "L" 32.3 (1.27) 48.26 (1.900) 2.55 (.10) 45˚ 45.72 (1.800) ø 95.5 (3.76) Max A A 80.0 (3.118) ø 44.40/44.45 (1.748/1.750) B B 2 x 22.86 (.900) ø 82.55 (3.250) 7/8-14 SAE O-Ring 3/8-16 UNC Code FS disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 7.58 7.80 8.07 8.35 8.66 8.80 Poids/Peso (lb) (13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5) (16.2) (16.7) (17.2) (17.8) (18.4) (19.1) (19.4) Length "L" mm 120.1 121.6 124.8 127.9 131.1 137.5 143.8 150.2 156.5 162.9 169.2 175.6 184.2 188.3 "L" (in) (4.73) (4.79) (4.91) (5.04) (5.16) (5.41) (5.66) (5.91) (6.16) (6.41) (6.66) (6.91) (7.25) (7.41) English equivalents for metric specifications are shown in ( ). 001 TC.indd, js 17 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série Code A Code F Code: 10 1" Keyed 44.7 (1.76) Code: 11 1" 6B Spline 44.7 (1.76) Code: 13 Long 1" Keyed 49.3 (1.94) English equivalents for metric specifications are shown in ( ). 001 TC.indd, js 18 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TC Series / Serie / Série 19.00 (.748) Code: 10 1/4 x 1 SAE J502 6.37 (.251) 6.35 (.250) 1" Keyed 28.30 (1.114) 27.64 (1.088) ø 25.37 / 25.40 (.999 / 1.00) 1/4-20 UNC 15.8 (.62) 38.6 (1.52) 6B SAE J499 Code: 11 38.6 (1.52) 1" 6B Spline ø 23.62 (.930) 23.42 (.922) 1/4-20 UNC 15.8 (.62) 1.32 (.052) 1.17 (.046) 4.31 (.169) 25.4 (1.00) MIN 1.24 (.049) 19.0 (.748) 1/4 x 1 SAE J502 ø 28.30 (1.14) 27.64 (1.088) Code: 13 Long 1" Keyed 44.5 (1.75) 1.32 (.052) 1.17 (.046) 60o 6.27 (.247) 6.20 (.244) 21.53 (.848) 21.28 (.838) ø 25.32 (.997) 25.02 (.985) 6.37 (.251) 6.35 (.250) ø 25.37 / 25.40 (.999 / 1.00) English equivalents for metric specifications are shown in ( ). 001 TC.indd, js 19 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information / Technische Information / Segni / Informacion Tecnica (2.2 – 24.0 in3/rev) 36 . . . 390 cm3/rev 15 Displacements 15 Schluckvolumen 15 Cylindrée 15 Despazamientos Cont Maximum Pressure (to1800 psi) Eingangsdruck . . .125 bar Chaute de pression max. Presion Maxima Int (to 2400 psi) . . .165 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite (to 15 gpm) . . . 57 lpm Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque Max Drehmoment Couple Maxi Torque Maximo LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série A Light to Medium Duty Low Speed, High Torque Motor This light to medium duty motor incorporates all the features of heavy duty motors. Design features include a high pressure shaft seal so external drains are never required, roller vane technology for automatic wear compensation, and full flow internal cooling and flushing. This is a very economical motor for most light to medium duty applications. (932 rpm) 932 rpm Cont (3897 lb in) 440 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral Int (4783 lb in) 540 Nm (to 1100 lb) . . . 4900 N 002 TB.indd, js 20 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l De ndré luck acem sp e v olu ent az am me Ma i n en x tos Ma . spe e x Vit . Dre d @ es hz Ma s ah x Ve e loc de l Int . inte ida rot erm rm a it t d m t io Ma it x ax n m tiere ent fl im Ma . oil nd o flo a a axi er w x Be ca Dé . Sch w t rie u bit lu da b: Ca d´h cks l in t ud t r u e rm al ile m om M i ten Ma ax ax x te i i ma Ma . Diff mo d x im e re x. e Ac Ch Dru nti o ute ck al P eite g Pr r e d e e s e p f ä ll s s ure io e r Ma n di essio fer x. n en m Ma sup c ia a x i x p Pr . Ein ly pr l ma es ga x e Pr sion ngs ssur ima es e d m r ion uc a ma xi en k Ma x im t ré x ad e Ma . torq ea x. u lim e Co Dre en up hm tac To le m om ion rqu en t e M axi Ma ax im x o Ma . per for x. Pu Lei ma st nc is Ma sanc unga e xim e d bg o r e s abe Mi ed ort n. inm ie s Mi tar ien max n. t in to i Co Anl g to up au r q To le m fmo ue rqu m e m in. fo ent ini urn mo i a de u dé a rr m an anr qu e age LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série max bar psi cont / int* Nm lb-in 165 2400 190 2750 48 427 67 596 6.6 8.8 44 385 50 440 125 1800 165 2400 190 2750 64 526 88 731 7.2 9.7 39 341 52 461 34 9 125 1800 165 2400 190 2750 78 693 107 946 7.5 10.1 36 319 70 619 34 9 34 9 125 1800 165 2400 190 2750 107 946 145 1284 7.8 10.4 66 582 99 977 409 34 9 34 9 125 1800 165 2400 190 2750 135 1193 184 1624 7.8 10.5 92 816 139 1226 98 6.0 454 45 12 45 12 125 1800 165 2400 190 2750 159 1411 217 1917 10.2 13.8 119 1050 158 1400 TB 0130 130 8.0 430 45 12 57 15 125 1800 165 2400 190 2750 220 1951 297 2632 13.4 18.0 167 1482 229 2024 TB 0165 163 10.0 343 45 12 57 15 125 1800 155 2250 190 2750 273 2418 346 3062 12.4 16.7 199 1760 263 2331 TB 0195 195 11.9 287 45 12 57 15 125 1800 145 2100 190 2750 340 3011 400 3537 12.0 16.1 270 2388 325 2872 TB 0230 228 13.9 246 45 12 57 15 103 1500 138 2000 190 2750 316 2797 427 3782 11.0 14.8 261 2354 353 3121 TB 0260 260 15.9 216 45 12 57 15 100 1450 131 1900 190 2750 350 3096 465 4117 10.5 14.1 291 2573 395 3498 TB 0295 293 17.9 191 45 12 57 15 97 1400 125 1800 190 2750 383 3391 499 4415 10.0 13.4 308 2724 400 3544 TB 0330 328 20.0 171 45 12 57 15 93 1350 114 1650 190 2750 413 3657 509 4505 9.1 12.2 332 2942 406 3590 TB 0365 370 22.6 151 45 12 57 15 86 1250 105 1525 190 2750 440 3897 540 4783 8.7 11.6 372 3296 454 4021 TB 0390 392 24.0 143 45 12 57 15 83 1200 100 1450 190 2750 428 3792 525 4642 7.8 10.5 339 3003 434 3845 cont / int* l/min g/min cont / int* bar psi Motor Series TB cm3/rev in3/rev rev/min TB 0036 36 2.2 932 34 9 34 9 125 1800 TB 0045 41 2.5 805 34 9 34 9 TB 0050 49 3.0 678 34 9 TB 0065 65 4.0 511 TB 0080 82 5.0 TB 0100 Performance data based on testing using 10W40 oil with a viscosity of 43,1 cSt. (200 SUS) at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. max KW HP cont / int* Nm lb-in operation rating applies to 10% of every minute. * Intermittent Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. 002 TB.indd, js 21 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TB Series Code 0036 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 XXXX Displacement Schluckvolumen Cylindrée Desplazamiento cm3/U cm3/tr cm3/giro cu in3/rev 36 41 49 65 82 98 130 163 195 228 260 293 238 370 392 / / / / / / / / / / / / / / / 2.2 2.5 3.0 4.0 5.0 6.0 8.0 10.0 11.9 13.9 15.9 17.9 20.0 22.6 24.0 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série XX XX 0 XXXX Mounting/Ports Gehäuse/Anschluß Carter/Plan de raccordement Montaje/Lumbreras Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion Options Opciones Code Code Mounting/Ports 0 SAE "A" 2 Bolt, 5/16-18 UNC Manifold Rotation Standard AM Code SAE "A" 2 Bolt, AP 1/2-14 NPTF 09 Shaft 1" Straight w/0.38" Crosshole 1" Keyed 10 SAE "A" 2 Bolt, 7/8-14 SAE 1" 6B Spline AS 11 Long 1" Keyed 4 Bolt, 5/16-18 UNC Manifold 13 FM 21 1" Keyed; Corrosion Resistant 4 Bolt, 1/2-14 NPTF 25mm Keyed w/ 8mm Key FP 26 7/8" 13 Tooth Spline 4 Bolt, 7/8-14 SAE 28 FS Code AAAB AAAA Options No Paint No lackiert Black Paint Schwarz lackiert For other available options, see pages 64-69. 002 TB.indd, js 22 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série TB 0036 2 5 US 10 Schluckstrom [L/min] 20 30 25 34 15 Flow [G/min] 0.5 1 45 40 70 4 3 5 9 7 12 600 2400 165 60 500 2000 Torque [lb/in] 140 125 40 100 30 400 1800 psi 50 bar Drehmoment [Nm] 2 700 80 1500 300 200 20 1000 70 100 10 35 0 0 200 400 600 800 Drehzahl [1/min] TB 0045 2 5 1000 1200 500 0 0 1400 200 400 600 800 1000 1200 1400 Speed [Rpm] US 10 Schluckstrom [L/min] 20 25 15 30 34 0.5 1 100 2 Flow [G/min] 5 4 3 7 9 900 90 800 16 80 2400 14 60 1 50 10 40 30 2000 600 1800 500 1500 psi 70 Torque [lb in] Drehmoment [Nm] 700 400 300 7 20 1000 200 3 10 500 100 0 0 100 200 300 400 500 Drehzahl [1/min] 600 700 0 800 0 100 200 300 400 500 Speed [Rpm] 600 700 800 TB 0050 2 5 15 10 Schluckstrom [L/min] 20 25 30 0.5 1 34 2 3 4 Flow [G/min] 5 US 7 9 1000 120 2400 900 165 100 800 2000 700 1800 80 100 40 600 1500 500 psi 60 Torque [lb in] 125 bar Drehmoment [Nm] 140 400 1000 300 70 200 20 35 500 100 0 0 0 Cont. 100 200 300 400 Drehzahl [1/min] 500 600 0 700 100 200 300 400 Speed [Rpm] 500 600 700 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 002 TB.indd, js 23 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série TB 0065 2 5 10 Schluckstrom [L/min] 20 25 15 30 34 0.5 1 160 165 1200 140 1000 7 9 80 100 2000 1800 60 70 800 1500 600 1000 400 40 200 35 20 2400 psi 125 Torque [lb in] 100 bar 120 500 0 0 0 100 200 300 Drehzahl [1/min] 400 500 0 550 100 200 300 Speed [Rpm] TB 0080 2 400 500 550 US 10 5 Flow [G/min] Schluckstrom [L/min] 20 25 15 30 0.5 1 1800 34 200 3 2 4 5 7 9 1600 180 2400 165 1400 160 2000 140 140 1200 1800 100 100 80 70 60 1000 1500 psi 120 Torque [lb in] 125 bar Drehmoment [Nm] US Flow [G/min] 5 4 3 1400 140 Drehmoment [Nm] 2 800 600 1000 400 40 35 20 500 200 0 0 0 50 100 150 200 250 Drehzahl [1/min] 300 350 400 450 0 50 0.5 1 2 100 150 200 250 Speed [Rpm] 300 350 400 450 TB 0100 2 5 15 10 20 Schluckstrom [L/min] 25 30 40 45 240 3 4 US Flow [G/min] 7 9 5 12 2000 220 2400 1800 165 1600 140 140 125 1800 1200 120 100 100 1500 1000 80 800 1000 600 70 60 2000 1400 Torque [lb in] 160 bar Drehmoment [Nm] 180 400 40 35 20 500 200 0 0 0 50 Cont. 100 150 200 250 300 Drehzahl [1/min] 350 400 450 500 0 50 100 150 200 250 300 Speed [Rpm] 350 400 450 500 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 002 TB.indd, js 24 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA psi 200 Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série TB 0130 2 5 15 10 20 Schluckstrom [L/min] 30 40 25 45 57 0.5 1 350 3 2 4 Flow [G/min] 9 7 5 US 12 15 2800 2600 300 2400 2400 2000 Torque [lb in] 200 125 150 2000 1800 140 100 1800 1600 1400 1500 1200 psi 250 bar Drehmoment [Nm] 2200 165 1000 800 100 70 1000 600 400 50 200 35 500 0 0 0 50 100 150 200 250 Drehzahl [1/min] 300 350 400 0 450 50 100 150 200 250 Speed [Rpm] 300 350 400 TB 0165 2 5 450 US 15 10 Schluckstrom [L/min] 30 40 25 20 45 0.5 1 2 3300 57 400 3 5 4 Flow [G/min] 9 7 12 15 3000 350 2250 2700 155 2400 1800 2100 250 Torque [lb in] 125 1800 100 1500 psi 200 bar Drehmoment [Nm] 300 1500 150 1200 70 100 1000 900 600 50 300 35 0 500 0 0 50 100 150 200 Drehzahl [1/min] 250 300 350 0 50 100 150 200 Speed [Rpm] 250 300 350 TB 0195 2 5 10 15 20 25 Schluckstrom [L/min] 30 40 45 57 0.5 1 2 3 4 5 7 US Flow [G/min] 9 12 15 3750 450 3500 400 3250 145 Torque [lb in] 250 100 200 150 1800 2500 125 70 2250 1500 2000 psi 300 2750 bar Drehmoment [Nm] 2100 3000 350 1750 1500 1250 1000 1000 100 750 500 50 35 500 250 0 0 0 Cont. 50 100 150 Drehzahl [1/min] 200 250 0 300 50 100 150 Speed [Rpm] 200 250 300 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 002 TB.indd, js 25 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série TB 0230 2 5 15 10 20 25 Schluckstrom [L/min] 30 40 45 57 2 0.5 1 500 3 5 4 7 Flow [G/min] 9 US 12 15 4000 450 3500 2000 400 3000 350 2500 200 1500 psi 103 250 Torque [lb in] 300 bar Drehmoment [Nm] 138 2000 1000 1500 70 150 1000 100 50 500 35 0 500 0 0 50 100 150 Drehzahl [1/min] 200 250 0 50 100 150 Speed [Rpm] 200 250 TB 0260 2 US 10 5 15 Schluckstrom [L/min] 25 40 30 20 45 57 0.5 1 500 2 3 Flow [G/min] 9 7 5 4 12 15 4500 4000 131 1900 3500 3000 100 200 70 1450 2500 psi Torque [lb in] 300 bar Drehmoment [Nm] 400 2000 1000 1500 1000 100 500 35 0 500 0 0 40 20 60 80 100 120 140 Drehzahl [1/min] 160 180 200 220 0 20 60 40 80 100 120 140 Speed [Rpm] 160 180 200 220 TB 0295 2 5 10 15 20 25 Schluckstrom [L/min] 30 40 45 0.5 1 2 57 3 4 5 7 Flow [G/min] 9 US 12 15 5000 600 4500 500 4000 200 70 3000 1400 2500 psi 97 Torque [lb/in] 300 bar Drehmoment [Nm] 1800 3500 125 400 2000 1000 1500 1000 100 500 500 35 0 0 0 20 Cont. 40 60 80 100 120 Drehzahl [1/min] 140 160 180 0 200 20 40 60 80 100 120 Speed [Rpm] 140 160 180 200 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 002 TB.indd, js 26 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série TB 0330 2 5 10 15 Schluckstrom [L/min] 30 40 45 25 20 0.5 1 2 57 3 4 7 5 US Flow [G/min] 9 12 15 5000 600 4500 4000 1650 114 3500 93 300 70 200 3000 1350 2500 2000 1000 psi Torque [lb in] 400 bar Drehmoment [Nm] 500 1500 1000 100 35 0 0 20 40 60 5 120 140 160 0 180 0 20 40 60 80 100 Speed [Rpm] 120 140 160 180 US TB 0370 2 80 100 Drehzahl [1/min] 500 500 10 20 15 Schluckstrom [L/min] 40 25 30 45 57 0.5 1 600 3 2 4 Flow [G/min] 7 9 5 12 15 5000 4500 4000 105 70 200 3000 1250 2500 1000 2000 psi 86 300 1525 3500 Torque [lb in] 400 bar Drehmoment [Nm] 500 1500 1000 100 500 500 35 0 0 0 20 40 60 80 100 Drehzahl [1/min] 120 140 0 160 20 40 60 80 100 Speed [Rpm] 120 140 160 TB 0390 2 5 10 20 15 25 Schluckstrom [L/min] 40 30 US 45 57 0.5 1 600 2 3 5 4 7 Flow [G/min] 9 12 15 5000 4500 500 1450 3500 83 300 70 200 1200 3000 2500 1000 psi Torque [lb in] 400 bar Drehmoment [Nm] 4000 100 2000 1500 1000 100 500 35 500 0 0 0 Cont. 20 40 60 80 100 Drehzahl [1/min] 120 0 140 150 20 40 60 80 Speed [Rpm] 100 120 140 150 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 002 TB.indd, js 27 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shaft Side Load Capacity N (lb) Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série 8896 (2000) 8007 (1800) 7117 (1600) 6228 (1400) 5338 (1200) 4448 (1000) 3559 (800) 2669 (600) 1779 (400) 890 (200) 0 0.0 400.0 200.0 600.0 800.0 Speed (RPM) 0.5 In. 1.0 In. 1.5 In. 6 The allowable side load curve is based on bushing life of 2.5 x 10 revolutions. Die zulaessige radiale Wellenbelastung bezieht sich auf die Lager-Lebensdauer 2,5 x 106 Umdrehungen. L’effort radial admissible sur l’arbre depend a une duree de vie 2,5 x 106 de rotation. La curva de carga lateral admisible se basa en vida util de cojinete de 2.5 x 10 revoluciones. 12.7 (.5) 25.4 (1.0) 38.1 (1.5) English equivalents for metric specifications are shown in ( ). 002 TB.indd, js 28 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting, Ports/Gehäuse, Anschlüße Carter, Orifices / Montaje, Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série Code: AM “L” 48.3 (1.90) 4 x 5/16-18 UNC 12.7 (.50) SAE A 2-Bolt, 5/16-18 UNC Manifold 2.55 (.10) 14.2 (.56) 48.27 (1.94) 63.50 (2.500) ø 95.5 (3.76) 45.7 (1.8) A A ø 82.50 / 82.55 (3.248 / 3.250) A B A 28.56 (1.125) A--A 48.26 (1.900) 127.3 (5.01) B 2x 31.75 (1.250) 2 x 14.28 (.562) 13.69 / 13.28 (.539 / .523) Motor with manifold mount is supplied with 2 O-rings. Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni è corredato da 2 OR. Code AM disp. 0036 0045 0050 0065 0080 0100 0130 0165 0195 5.87 6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 Poids/Peso (lb) (12.9) (13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5) (16.2) Length"L" mm 132.4 136 138 141 144 147 154 160 166 "L" (in) (5.22) (5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) Weight/Gewicht kg 0230 0260 ø 106.38 (4.188) 0295 0330 0365 0390 7.58 7.80 8.07 8.35 8.66 8.80 (16.7) (17.2) (17.8) (18.4) (19.1) (19.4) 173 179 185 192 200 205 6.79 7.04 7.29 7.54 7.88 8.04 Code: AP SAE A 2-Bolt, 1/2-14 NPTF “L” 48.3 (1.90) 2.55 (.10) 14.2 (.56) 48.26 (1.900) 48.27 (1.94) 45.72 (1.800) A A ø 82.50 / 82.55 (3.248 / 3.250) ø 95.5 (3.76) 127.3 (5.01) B B 2 x 22.86 (.900) 13.69 / 13.28 (.539 / .523) 1/2-14 NPTF ø 106.38 (4.188) Code AP disp. 0036 0045 0050 0065 0080 0100 0130 0165 0195 5.87 6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 Poids/Peso (lb) (12.9) (13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5) (16.2) Length"L" mm 132.4 136 138 141 144 147 154 160 166 "L" (in) (5.22) (5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) Weight/Gewicht kg 0230 0260 0295 0330 0365 0390 7.58 7.80 8.07 8.35 8.66 8.80 (16.7) (17.2) (17.8) (18.4) (19.1) (19.4) 173 179 185 192 200 205 6.79 7.04 7.29 7.54 7.88 8.04 English equivalents for metric specifications are shown in ( ). 002 TB.indd, js 29 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting, Ports/Gehäuse, Anschlüße Carter, Orifices / Montaje, Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série Code: AS SAE A 2-Bolt, 7/8"-14 SAE O-Ring “L” 48.3 (1.90) 2.55 (.10) 14.2 (.56) 48.26 (1.900) 48.27 (1.94) 45.72 (1.800) A A ø 82.50 / 82.55 (3.248 / 3.250) ø 95.5 (3.76) 127.3 (5.01) B B 2 x 22.86 (.900) 13.69 / 13.28 (.539 / .523) 7/8-14 SAE O-Ring ø 106.38 (4.188) Code AS disp. 0036 0045 0050 0065 0080 0100 0130 0165 0195 5.87 6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 Poids/Peso (lb) (12.9) (13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5) (16.2) Length"L" mm 132.4 136 138 141 144 147 154 160 166 "L" (in) (5.22) (5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) Weight/Gewicht kg 0230 0365 0390 7.58 7.80 8.07 8.35 8.66 (16.7) (17.2) (17.8) (18.4) (19.1) 173 179 185 192 200 6.79 7.04 7.29 7.54 7.88 0260 0295 0330 8.80 (19.4) 205 8.04 Code: FM 4-Bolt, 5/16-18 UNC Manifold "L" 48.3 (1.90) 4 x 5/16-18 UNC 12.7 (.50) 45˚ 48.26 (1.900) 2.55 (.10) 63.50 (2.500) ø 95.5 (3.76) A 45.7 (1.8) A A B B 2x 31.75 (1.250) A 28.56 (1.125) 80 (3.118) ø 44.40 / 44.45 (1.748 / 1.750) 48.27 (1.94) ø 82.55 (3.250) 2 x 14.28 (.562) 3/8-16 UNC A--A Motor with manifold mount is supplied with 2 O-rings. Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni è corredato da 2 OR. Code FM disp. 0036 5.58 Poids/Peso (lb) (12.3) Length"L" mm 132.4 "L" (in) (5.22) Weight/Gewicht kg 0045 0050 0065 0080 0100 5.62 5.67 5.80 5.94 6.08 (12.4) (12.5) (12.8) (13.1) (13.4) 136 138 141 144 147 (5.36) (5.42) (5.54) (5.67) (5.79) 0130 0165 0195 0230 0260 0295 0330 6.31 6.62 7.03 7.17 7.39 7.62 7.94 (13.9) (14.6) (15.5) (15.8) (16.3) (16.8) (17.5) 154 160 166 173 179 185 192 (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) 0365 English equivalents for metric specifications are shown in ( ). 002 TB.indd, js 30 0390 8.26 8.39 (18.2) (18.5) 200 205 (7.88) (8.04) Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting, Ports/Gehäuse, Anschlüße Carter, Orifices / Montaje, Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série Code: FP "L" 48.3 (1.90) 4 Bolt, 1/2-14 NPTF 45˚ 48.26 (1.900) 2.55 (.10) 45.72 (1.800) A A ø 95.5 (3.76) 80.0 (3.118) ø 44.40 / 44.45 (1.748 / 1.750) B B 2 x 22.86 (.900) 1/2-14 NPTF Code FP disp. 0036 0045 0050 0065 0080 48.27 (1.94) ø 82.55 (3.250) 0100 5.58 5.62 5.67 5.80 5.94 6.08 Poids/Peso (lb) (12.3) (12.4) (12.5) (12.8) (13.1) (13.4) Length"L" mm 132.4 136 138 141 144 147 "L" (in) (5.22) (5.36) (5.42) (5.54) (5.67) (5.79) Weight/Gewicht kg 0130 0165 0195 0230 3/8-16 UNC 0260 0295 0330 6.31 6.62 7.03 7.17 7.39 7.62 7.94 (13.9) (14.6) (15.5) (15.8) (16.3) (16.8) (17.5) 154 160 166 173 179 185 192 (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) 0365 0390 8.26 8.39 (18.2) (18.5) 200 205 (7.88) (8.04) Code: FS 4 Bolt, 7/8"-14 SAE O-Ring "L" 48.3 (1.90) 45˚ 48.26 (1.900) 2.55 (.10) 45.72 (1.800) A A ø 95.5 (3.76) 80.0 (3.118) ø 44.40 / 44.45 (1.748 / 1.750) B B 2 x 22.86 (.900) 7/8-14 SAE O-Ring Code FS disp. 0036 0045 0050 0065 0080 0100 5.58 5.62 5.67 5.80 5.94 6.08 Poids/Peso (lb) (12.3) (12.4) (12.5) (12.8) (13.1) (13.4) Length"L" mm 132.4 136 138 141 144 147 "L" (in) (5.22) (5.36) (5.42) (5.54) (5.67) (5.79) Weight/Gewicht kg 48.27 (1.94) ø 82.55 (3.250) 0130 0165 0195 0230 3/8-16 UNC 0260 0295 0330 6.31 6.62 7.03 7.17 7.39 7.62 7.94 (13.9) (14.6) (15.5) (15.8) (16.3) (16.8) (17.5) 154 160 166 173 179 185 192 (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) 0365 English equivalents for metric specifications are shown in ( ). 002 TB.indd, js 31 0390 8.26 8.39 (18.2) (18.5) 200 205 (7.88) (8.04) Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série Code A Code F Code: 09 1" Straight with 0.38" Crosshole 44.7 (1.76) Code: 10 1" Keyed Code: 21 44.7 (1.76) Corrosion Resistant Code: 11 1" 6B Spline 44.7 (1.76) Code: 13 Long 1" Keyed 49.3 (1.94) English equivalents for metric specifications are shown in ( ). 002 TB.indd, js 32 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes Code: 09 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série ø 9.53 / 9.91 (.375 / .390) 1" Straight with 0.38" Crosshole 14.52 (.571) 13.51 (.531) ø 25.37 / 25.40 (.999 / 1.00) 38.6 (1.52) Code: 10 19.00 (.748) 1/4 x 1 SAE J502 1" Keyed Code: 21 28.30 (1.114) 27.64 (1.088 ) Corrosion Resistant 1/4-20 UNC (15.8) .62 6.37 (.251) 6.35 (.250) ø 27.97 (1.101) ø 25.37 / 25.40 (.999 / 1.00) 38.6 (1.52) 6B SAE J499 Code: 11 38.6 (1.52) ø 25.32 (.997) 25.02 (.985) 1" 6B Spline 1/4-20 UNC 15.8 (.62) 1.32 (.052) 1.17 (.046) 4.88 (.192) 25.4 (1.00) MIN 1.24 (.049) 19.0 (.748) 1/4 x 1 SAE J502 ø 28.30 (1.14) 27.64 (1.088) Code: 13 Long 1" Keyed 43.2 (1.700) 1.32 (.052) 1.17 (.046) 60o 6.27 (.246) 6.20 (.244) ø 21.54 (.848) 21.29 (.838) 6.37 (.251) 6.35 (.250) ø 25.37 / 25.40 (.999 / 1.00) English equivalents for metric specifications are shown in ( ). 002 TB.indd, js 33 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série Code A Code F Code: 26 25mm Keyed with 8mm Key 50.4 (1.98) Code: 28 7/8" 13 Tooth Spline 41.4 (1.63) English equivalents for metric specifications are shown in ( ). 002 TB.indd, js 34 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes Code: 26 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TB Series / Serie / Série Key A8 x 7 x 23 mm ø25.015 (.98) 25.002 (.98) 25mm Keyed with 8mm Key 8.00 (.315) 7.96 (.313) M8 x 1.25 19 (.75) 42.6 (1.677) 17.8 (.70) MIN Code: 28 ø 22.15 (.872) 21.90 (.862) SAE J498 16/32 Spline 7/8" 13 Tooth Spline 18.2 (.715) 17.9 (.705) English equivalents for metric specifications are shown in ( ). 002 TB.indd, js 35 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information / Technische Information / Segni / Informacion Tecnica (2.2 – 24.0 in3/rev) 36 . . . 390 cm3/rev 15 Displacements 15 Schluckvolumen 15 Cylindrée 15 Despazamientos Cont Maximum Pressure (to1800 psi) Eingangsdruck . . .125 bar Chaute de pression max. Presion Maxima Int (to 2400 psi) . . .165 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite (to 15 gpm) . . . 57 lpm Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque Max Drehmoment Couple Maxi Torque Maximo LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série A Stainless Steel Low Speed, High Torque Motor This motor utilizes a stainless steel front housing and output shaft, with a glass filled polypropylene rear cover for the ultimate in corrosion protection. It is designed for use under water or in harsh environments where it will be exposed to water or corrosive chemicals. Features such as roller vanes, high pressure shaft seal and full flow spline lubrication are standard. (932 rpm) 932 rpm Cont (2000 lb in) 226 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral Int (2000 lb in) 226 Nm (to 300 lb) . . . 1340 N 003 TS.indd, js 36 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l De ndré luck acem sp e v olu ent az am me Ma i n en x tos Ma . spe e x Vit . Dre d @ es hz Ma s ah x Ve e loc de l Int . inte ida rot erm rm a it t d m t io Ma it x ax n m tiere ent fl im Ma . oil nd o flo a a axi er w x Be ca Dé . Sch w t r ie u bit lu da b: Ca d´h cks l in t ud t r u e rm al ile m om M i ten Ma ax ax x te i i ma Ma . Diff mo d x im e re x. e Ac Ch Dru nti o ute ck al P eite g Pr r e d e e s e p f ä ll s s ure io e r Ma n di essio fer x. n en m Ma sup c ia a x i x p Pr . Ein ly pr l ma es ga x e Pr sion ngs ssur ima es e d m r ion uc a ma xi en k Ma x im t ré x ad e Ma . torq ea x. u lim e Co Dre en up hm tac To le m om ion rqu en t e M axi Ma ax im x o Ma . per for x. Pu Lei ma st nc is Ma sanc unga e xim e d bg o r e s abe Mi ed ort n. inm ie s Mi tar ien max n. t in to i Co Anl g to up au r q To le m fmo ue rqu m e m in. fo ent ini urn mo i a de u dé a rr m an anr qu e age LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série Motor Series TS cm3/rev in3/rev rev/min cont / int* l/min g/min cont / int* bar psi max bar psi cont / int* Nm lb-in TS 0036 36 2.2 932 34 9 34 9 125 1800 TS 0045 41 2.5 805 34 9 34 9 TS 0050 49 3.0 678 34 9 TS 0065 65 4.0 511 TS 0080 82 5.0 TS 0100 165 2400 190 2750 48 427 67 596 6.6 8.8 44 385 50 440 125 1800 165 2400 190 2750 64 526 88 731 7.2 9.7 39 341 52 461 34 9 125 1800 165 2400 190 2750 78 693 107 946 7.5 10.1 36 319 70 619 34 9 34 9 125 1800 165 2400 190 2750 107 946 145 1284 7.8 10.4 66 582 99 977 409 34 9 34 9 125 1800 165 2400 190 2750 135 1193 184 1624 7.8 10.5 92 816 139 1226 98 6.0 454 45 12 45 12 125 1800 165 2400 190 2750 160 1411 217 1917 10.2 13.8 119 1050 158 1400 TS 0130 130 8.0 430 45 12 57 15 131 1900 131 1900 190 2750 226 2000 226 2000 10.1 13.6 172 1520 172 1520 TS 0165 163 10.0 343 45 12 57 15 103 1500 103 1500 190 2750 226 2000 226 2000 8.1 10.9 165 1460 165 1460 TS 0195 195 11.9 287 45 12 57 15 83 1200 83 1200 190 2750 226 2000 226 2000 6.8 9.1 179 1586 179 1586 TS 0230 228 13.9 246 45 12 57 15 76 1100 76 1100 190 2750 226 2000 226 2000 5.8 7.8 190 1680 190 1680 TS 0260 260 15.9 216 45 12 57 15 69 1000 69 1000 190 2750 226 2000 226 2000 5.1 6.9 188 1660 188 1660 TS 0295 293 17.9 191 45 12 57 15 62 900 62 900 190 2750 226 2000 226 2000 4.6 6.1 181 1600 181 1600 TS 0330 328 20.0 171 45 12 57 15 41 600 41 600 190 2750 226 2000 226 2000 4.0 5.4 181 1600 181 1600 TS 0365 370 22.6 151 45 12 57 15 41 600 41 600 190 2750 226 2000 226 2000 3.6 4.8 191 1690 191 1690 TS 0390 392 24.0 143 45 12 57 15 41 600 41 600 190 2750 226 2000 226 2000 3.4 4.5 179 1580 179 1580 Performance data based on testing using 10W40 oil with a viscosity of 43,1 cSt. (200 SUS) at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. max KW HP cont / int* Nm lb-in operation rating applies to 10% of every minute. * Intermittent Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 003 TS.indd, js 37 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TS Series Code 0036 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série XXXX XX Displacement Schluckvolumen Cylindrée Desplazamiento Mounting/Ports Gehäuse/Anschluß Carter/Plan de raccordement Montaje/Lumbreras cm3/U cm3/tr cm3/giro cu in3/rev 36 41 49 65 82 98 130 163 195 228 260 293 238 370 392 / / / / / / / / / / / / / / / 2.2 2.5 3.0 4.0 5.0 6.0 8.0 10.0 11.9 13.9 15.9 17.9 20.0 22.6 24.0 XX Shaft Welle Arbre Eje 0 XXXX Rotation Drehrichtung Direction de rotation Rotacion Options Opciones Code Code Rotation B Mounting/Ports 0 4 Bolt, 7/8-14 SAE A Standard FS Code 77 Shaft 1" Square Keyed Stainless Steel Code AAXH Options Fluorocarbon Body, Shaft, Dirt & Water Seals. Vespel Commutator Seals. For other available options, see pages 64-69. 003 TS.indd, js 38 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série TS 0036 2 5 US 10 Schluckstrom [L/min] 20 30 25 34 15 Flow [G/min] 0.5 1 45 40 70 4 3 5 9 7 12 600 2400 165 60 500 2000 140 125 40 bar 100 30 400 1800 psi 50 Torque [lb/in] Drehmoment [Nm] 2 700 80 1500 300 200 20 1000 70 100 10 35 0 0 200 400 600 800 Drehzahl [1/min] TS 0045 2 5 1000 1200 500 0 0 1400 200 400 600 800 1000 1200 1400 Speed [Rpm] US 10 Schluckstrom [L/min] 20 25 15 30 34 0.5 1 100 2 Flow [G/min] 5 4 3 7 9 900 90 125 50 100 40 30 2000 600 70 1800 500 1500 psi 140 60 Torque [lb in] 70 2400 700 bar Drehmoment [Nm] 800 165 80 400 300 1000 20 200 35 10 500 100 0 0 100 200 300 400 500 Drehzahl [1/min] 600 700 800 0 0 100 200 300 400 500 Speed [Rpm] 600 700 800 TS 0050 2 5 15 10 Schluckstrom [L/min] 20 25 30 0.5 1 34 2 3 4 Flow [G/min] 5 US 7 9 1000 120 2400 900 165 100 800 2000 700 1800 80 100 40 600 1500 500 psi 60 Torque [lb in] 125 bar Drehmoment [Nm] 140 400 1000 300 70 200 20 35 500 100 0 0 0 Cont. 100 200 300 400 Drehzahl [1/min] 500 600 0 700 100 200 300 400 Speed [Rpm] 500 600 700 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 003 TS.indd, js 39 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série TS 0065 2 5 10 Schluckstrom [L/min] 20 25 15 30 34 0.5 1 160 165 1200 140 1000 7 9 80 100 2000 1800 60 70 800 1500 600 1000 400 40 200 35 20 2400 psi 125 Torque [lb in] 100 bar 120 500 0 0 0 100 200 300 Drehzahl [1/min] 400 500 0 550 100 200 300 Speed [Rpm] TS 0080 2 400 500 550 US 10 5 Flow [G/min] Schluckstrom [L/min] 20 25 15 30 0.5 1 1800 34 200 3 2 4 5 7 9 1600 180 2400 165 1400 160 2000 140 140 1200 1800 100 100 80 70 60 1000 1500 psi 120 Torque [lb in] 125 bar Drehmoment [Nm] US Flow [G/min] 5 4 3 1400 140 Drehmoment [Nm] 2 800 600 1000 400 40 35 20 500 200 0 0 0 50 100 150 200 250 Drehzahl [1/min] 300 350 400 450 0 50 0.5 1 2 100 150 200 250 Speed [Rpm] 300 350 400 450 TS 0100 2 5 15 10 20 Schluckstrom [L/min] 25 30 40 45 240 3 4 US Flow [G/min] 7 9 5 12 2000 220 2400 1800 165 1600 140 140 125 1800 1200 120 100 100 1500 1000 80 800 1000 600 70 60 2000 1400 Torque [lb in] 160 bar Drehmoment [Nm] 180 400 40 35 20 500 200 0 0 0 50 Cont. 100 150 200 250 300 Drehzahl [1/min] 350 400 450 500 0 50 100 150 200 250 300 Speed [Rpm] 350 400 450 500 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 003 TS.indd, js 40 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA psi 200 Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série TS 0130 2 5 10 15 20 US Schluckstrom [L/min] 25 30 40 45 57 250 131 200 150 100 bar Drehmoment [Nm] 125 100 70 50 35 0 0 50 100 150 200 250 Drehzahl [1/min] 300 350 400 450 TS 0165 2 5 US 10 15 20 Schluckstrom [L/min] 25 30 40 45 57 250 103 150 70 bar Drehmoment [Nm] 200 100 50 35 0 0 50 100 150 200 Drehzahl [1/min] 250 300 350 TS 0195 2 5 10 15 20 Schluckstrom [L/min] 25 30 40 US 45 57 250 83 150 70 bar Drehmoment [Nm] 200 100 50 35 0 0 50 100 150 200 250 300 Drehzahl [1/min] Cont. Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 003 TS.indd, js 41 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série TS 0230 US TS 0260 US TS 0295 US 62 Cont. Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 003 TS.indd, js 42 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série TS 0330 US US TS 0365 TS 0390 US Cont. Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 003 TS.indd, js 43 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série A 40-80 psi relief valve is installed in the polypropylene rear cover. If a motor section seal fails pressurizing the rear cavity, the relief valve will vent to atmosphere. If desired the relief valve outlet can be piped to the reservoir. Maximum side load 300# at 1 inch from mounting face. Shaft torque is limited to 2000 in-lbs since it is made from 316 stainless steel 1" keyed shaft. Other shaft types or shaft taper locks will increase allowable shaft torque. Code: FS 4 Bolt, 7/8"-14 SAE O-Ring 9.70±.06 (246.4±1.5) 1.77±.03 (45.0±.0.8) .110 (2.79) .090 (2.29) 1.910 (48.51) 1.890 (48.01) ±.04 (1.0) 1.910 (48.51) 1.890 (48.01) 1.365 (34.67) 1.345 (34.16) .155 (3.94) .135 (3.43) .250 (6.35) .248 (6.30) Port “A” 1.000 (25.40) .999 (25.37) 1.810 (45.97) 1.790 (45.46) 1.750 (44.45) 1.748 (44.40) .910 (23.11) .890 (22.60) Port “B” 1/4-20 UNC x .62 (15.7) Min. 3.250 (82.55) 7/8-14 Straight Thd O-Ring Ports Code FS disp. 0036 4x 3/8-16 UNC Thru 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 8.3 8.3 8.4 8.5 8.7 8.8 9.0 9.3 9.8 9.9 10.1 10.3 10.7 11.0 11.1 Poids/Peso (lb) (18.3) (18.4) (18.5) (18.8) (19.1) (19.4) (19.9) (20.6) (21.5) (21.8) (22.3) (22.8) (23.5) (24.2) (24.5) Length"Z" mm 164.4 165.5 167.0 170.2 173.3 176.5 182.9 189.2 195.6 201.9 208.3 214.6 221.0 229.6 233.7 "Z" (in) (6.47) (6.52) (6.57) (6.70) (6.82) (6.95) (7.20) (7.45) (7.70) (7.95) (8.20) (8.45) (8.70) (9.04) (9.20) Weight/Gewicht kg English equivalents for metric specifications are shown in ( ). 003 TS.indd, js 44 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Notes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TS Series / Serie / Série 003 TS.indd, js 45 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information / Technische Information / Segni / Informacion Tecnica (2.2 – 24.0 in3/rev) 36 . . . 390 cm3/rev 15 Displacements 15 Schluckvolumen 15 Cylindrée 15 Despazamientos Cont Maximum Pressure (to 2030 psi) Eingangsdruck . . .140 bar Chaute de pression max. Presion Maxima Int (to 2750 psi) . . .190 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite (to 20 gpm) . . . 75 lpm Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima (1000 rpm) 1000 rpm Maximum Torque Max Drehmoment Couple Maxi Torque Maximo Cont (4139 lb in) 467 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série An Improved Medium Duty Low Speed, High Torque Motor This medium duty motor has higher pressure ratings than the TB motor, for applications requiring higher torque. Robust roller bearings withstand higher side loads and are suitable for chain and sprocket shaft connections. It uses high pressure shaft seals, robust roller bearings and high flow shaft seal cooling. Int (5728 lb in) 648 Nm (to 1500 lb) . . . 6650 N 004 TE.indd, js 46 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l De ndré luck acem sp e v olu ent az am me Ma i n en x tos Ma . spe e x Vit . Dre d @ es hz Ma s ah x Ve e loc de l Int . inte ida rot erm rm a it t d m t io Ma it x ax n m tiere ent fl im Ma . oil nd o flo a a axi er w x Be ca Dé . Sch w t r ie u bit lu da b: Ca d´h cks l in t ud t r u e rm al ile m om M i ten Ma ax ax x te i i ma Ma . Diff mo d x im e re x. e Ac Ch Dru nti o ute ck al P eite g Pr r e d e e s e p f ä ll s s ure ion re e dif ssio Ma e re n m x. nc Ma sup ia l a x i x p ma Pr . Ein ly pr xim es ga e a Pr sion ngs ssur es e d ion max ruc k ma i en Ma x im t ré x ad e Ma . torq ea x. u e lim Co Dre en up hm tac To le m om ion rqu e a nt e M xi Ma ax im x o Ma . per for x. Pu Lei ma st nc is Ma sanc unga e xim e d bg o r e s abe Mi ed ort n. inm ie s Mi tar ien max n. t in to i Co Anl g to up au r q To le m fmo ue rqu m e m in. fo ent ini urn mo i a de u dé a rr m an anr qu e age LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série cont / int* l/min g/min cont / int* bar psi max bar psi cont / int* Nm lb-in max KW HP Motor Series TE cm3/rev in3/rev Int rev/min TE 0036 36 2.2 1141 34 9 42 11 140 2030 190 2750 200 2900 54.6 483 71.1 630 8.5 11.4 44 389 52 460 TE 0045 41 2.5 1024 34 9 42 11 140 2030 190 2750 200 2900 71 624 99 876 10.4 13.9 44 411 64 565 TE 0050 49 3.0 1020 34 9 50 13 140 2030 190 2750 200 2900 90 796 127 1120 12.8 17.2 72 637 98 871 TE 0065 65 4.0 877 45 12 57 15 140 2030 190 2750 200 2900 125 1106 176 1558 14.7 19.8 100 885 137 1211 TE 0080 82 5.0 695 45 12 57 15 140 2030 190 2750 200 2900 160 1416 220 1947 17.3 23.2 128 1133 171 1515 TE 0100 98 6.0 582 45 12 57 15 140 2030 190 2750 200 2900 190 1682 264 2337 17.4 23.4 152 1345 205 1819 TE 0130 130 8.0 438 45 12 57 15 140 2030 190 2750 200 2900 255 2257 352 3116 17.3 23.2 204 1806 274 2423 TE 0165 163 10.0 348 45 12 57 15 140 2030 190 2750 200 2900 310 2744 436 3846 17.0 22.8 248 2195 338 2992 TE 0195 195 11.9 292 45 12 57 15 140 2030 190 2750 200 2900 390 3452 528 4673 17.4 23.4 312 2762 411 3637 TE 0230 228 13.9 328 57 15 75 20 120 1740 165 2400 200 2900 380 3363 514 4554 17.7 23.8 304 2691 411 3637 TE 0260 260 15.9 287 57 15 75 20 110 1595 155 2250 200 2900 400 3540 550 4870 16.7 22.4 320 2832 449 3977 TE 0295 293 17.9 256 57 15 75 20 100 1450 145 2100 200 2900 428 3784 582 5180 15.7 21.0 328 2903 445 3939 TE 0330 328 20.0 228 57 15 75 20 100 1450 135 1950 200 2900 443 3926 600 5312 14.8 19.8 344 3045 453 4014 TE 0365 370 22.6 203 57 15 75 20 95 1378 125 1825 200 2900 467 4133 648 5728 13.6 18.2 373 3301 477 4223 TE 0390 392 24.0 191 57 15 75 20 85 1233 120 1740 200 2900 445 3935 628 5562 12.5 16.8 348 3080 462 4090 Performance data based on testing using 10W40 oil with a viscosity of 43,1 cSt. (200 SUS) at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. cont / int* Nm lb-in * Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 004 TE.indd, js 47 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TE Series Code 0036 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 XXXX Displacement Schluckvolumen Cylindrée Desplazamiento cm3/tr cm3/giro cm3/U cu in3/rev 36 41 49 65 82 98 130 163 195 228 260 293 328 370 392 / / / / / / / / / / / / / / / 2.2 2.5 3.0 4.0 5.0 6.0 8.0 10.0 11.9 13.9 15.9 17.9 20.0 22.6 24.0 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série X Mounting/Ports Gehäuse/Anschluß Carter/Plan de raccordement Montaje/Lumbreras XX 0 XXXX Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion Options Opciones Code Code Mounting/Ports 0 SAE "A" 2 Bolt, 5/16-18 UNC Manifold Rotation Standard AM SAE "A" 2 Bolt,1/2-14 NPTF Code Shaft 1" Straight w/0.38" Crosshole AP 09 SAE "A" 2 Bolt, 7/8-14 SAE 10 21 AS 1" Keyed Standard Corrosion Resistant Stainless Steel 1" 6B Spline 4 Bolt, 1/2-14 NPTF 11 FP Long 1" Keyed 13 4 Bolt , 7/8-14 SAE 1" Tapered 25 FS 25mm Keyed w/ 8mm Key 26 Wheel Mount, 7/8-14 SAE US Code AAAB AAAA Options No Paint No lackiert Black Paint Schwarz lackiert For other available options, see pages 64-69. 004 TE.indd, js 48 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série TE 0036 2 90 5 US 10 Schluckstrom [L/min] 20 25 30 15 34 42 0.5 1 800 80 3 4 5 Flow [G/min] 7 9 11 700 190 70 600 2750 60 140 40 100 2000 400 psi 50 Torque [lb/in] 500 bar Drehmoment [Nm] 2 1500 300 30 200 70 20 1000 100 10 500 35 0 0 0 200 400 600 Drehzahl [1/min] 800 1000 0 1200 200 400 600 Speed [Rpm] 800 1000 1200 TE 0045 2 5 US 10 15 Schluckstrom [L/min] 20 30 25 34 2 0.5 1 42 120 3 4 Flow [G/min] 5 7 9 11 1100 1000 100 900 190 2750 140 60 100 40 600 2000 psi Torque [lb in] 700 bar Drehmoment [Nm] 800 80 500 1500 400 300 70 100 35 0 1000 200 20 0 100 200 300 400 500 600 700 800 900 500 0 1000 0 100 200 300 400 500 600 700 800 900 1000 Speed [Rpm] Drehzahl [1/min] TE 0050 Schluckstrom [L/min] 24 8 11 15 19 34 27 0.5 1 2 1200 50 140 3 4 5 US Flow [G/min] 7 9 13 1100 120 1000 2750 900 100 140 60 100 40 700 2000 600 psi Torque [lb in] 800 80 bar Drehmoment [Nm] 190 500 1500 400 300 70 1000 200 20 100 500 35 0 0 100 200 300 400 500 600 700 800 900 0 1000 0 Drehzahl [1/min] Cont. 100 200 300 400 500 600 Speed [Rpm] 700 800 900 1000 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 004 TE.indd, js 49 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série TE 0065 US Schluckstrom [L/min] 2 5 180 10 15 25 20 30 40 45 0.5 1 2 57 3 4 Flow [G/min] 7 9 5 12 15 1750 160 1500 190 140 2750 Drehmoment [Nm] 1250 Torque [lb in] 120 1000 100 60 2000 psi 80 bar 140 100 750 1500 500 40 70 1000 250 20 35 0 0 100 200 300 400 500 600 700 500 0 800 850 0 100 200 300 5 7 Drehzahl [1/min] 10 600 700 800 850 US TE 0080 2 5 400 500 Speed [Rpm] Schluckstrom [L/min] 15 20 25 30 40 0.5 1 2 3 2000 57 45 220 4 Flow [G/min] 9 12 15 1800 200 190 2750 1600 160 120 100 100 80 1200 2000 1000 psi 140 Torque [lb in] 1400 140 bar Drehmoment [Nm] 180 1500 800 600 60 70 1000 400 40 200 20 35 500 0 0 0 100 200 300 400 500 600 0 700 100 200 300 400 500 600 Speed [Rpm] Drehzahl [1/min] TE 0100 US Schluckstrom [L/min] 2 5 10 15 20 25 30 40 45 0.5 1 2 3 2400 57 5 7 Flow [G/min] 9 12 15 2200 250 2750 2000 190 225 1800 200 1600 175 Torque [lb in] 140 150 125 100 bar Drehmoment [Nm] 4 100 75 2000 1400 1200 psi 275 700 1000 1500 800 600 70 50 1000 400 25 200 35 500 0 0 0 Cont. 100 200 300 Drehzahl [1/min] 400 500 0 600 100 200 300 400 500 600 Speed [Rpm] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 004 TE.indd, js 50 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série TE 0130 US Flow [G/min] 9 7 Schluckstrom [L/min] 2 5 400 10 15 20 25 40 30 45 0.5 1 2 57 350 4 5 12 15 3000 2750 190 300 2500 140 200 150 100 2000 2000 psi Torque [lb in] 250 bar Drehmoment [Nm] 3 3500 1500 1500 1000 100 1000 70 500 50 500 35 0 0 0 50 100 150 200 250 300 350 400 0 450 50 100 150 Drehzahl [1/min] 200 250 Speed [Rpm] 300 350 400 TE 0165 US Schluckstrom [L/min] 2 5 500 10 15 20 25 30 40 45 0.5 1 2 4000 57 4 5 12 15 2750 400 3200 190 2800 2000 2400 Torque [lb in] 300 140 250 200 100 2000 1500 1600 psi 350 bar Drehmoment [Nm] 3 Flow [G/min] 7 9 3600 450 1200 150 1000 70 100 800 400 50 500 35 0 0 0 50 100 150 200 250 300 0 350 50 100 150 Drehzahl [1/min] 200 250 300 US Schluckstrom [L/min] 2 5 10 350 Speed [Rpm] TE 0195 15 20 25 40 30 Flow [G/min] 45 57 0.5 1 2 5000 550 500 3 4 7 5 9 12 15 4500 190 450 2750 4000 400 3500 350 250 100 200 2000 1500 70 1000 1000 100 50 500 35 0 50 100 150 200 250 500 0 300 0 Drehzahl [1/min] Cont. 2000 2500 1500 150 0 3000 psi Torque [lb in] 140 300 bar Drehmoment [Nm] 450 50 100 150 Speed [Rpm] 200 250 300 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 004 TE.indd, js 51 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série TE 0230 US Schluckstrom [L/min] 550 0.5 1 2 5000 500 4500 2 5 10 15 20 25 30 40 50 57 75 4 7 5 15 20 4000 165 120 250 100 200 3000 Torque [lb in] 140 300 2400 3500 350 2000 2500 1750 2000 1500 1500 150 1000 70 100 1000 500 50 0 0 50 100 150 200 250 0 35 350 300 0 50 100 150 Drehzahl [1/min] 200 250 500 350 300 Speed [Rpm] US TE 0260 Schluckstrom [L/min] 2 5 600 10 15 20 25 30 50 40 Flow [G/min] 0.5 1 2 75 57 3 4 7 5 12 9 15 20 5000 550 4500 500 4000 2250 3500 Torque [lb in] 155 350 300 250 115 200 100 3000 1650 2500 psi 400 bar Drehmoment [Nm] 450 1500 2000 1500 150 1000 1000 100 70 500 50 0 50 100 150 Drehzahl [1/min] 200 250 500 300 0 35 300 0 0 50 100 150 Speed [Rpm] 200 250 TE 0295 US 10 15 20 25 30 Schluckstrom [L/min] 50 40 57 0.5 1 2 3 4 75 600 5500 550 5000 500 4500 450 5 7 Flow [G/min] 9 12 15 20 4000 145 400 2100 3500 Torque [lb in] 350 3000 300 105 1550 2500 bar 250 psi 2 5 Drehmoment [Nm] psi 400 bar Drehmoment [Nm] 450 3 Flow [G/min] 12 9 2000 200 1500 150 70 1000 1000 100 500 50 0 0 25 50 75 100 125 150 175 200 225 250 35 275 0 0 50 75 100 125 150 175 200 225 250 500 275 Speed [Rpm] Drehzahl [1/min] Cont. 25 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 004 TE.indd, js 52 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série TE 0330 US Schluckstrom [L/min] 2 5 10 15 20 25 30 40 50 57 0.5 1 2 75 650 5500 600 5000 550 4500 7 15 20 4000 450 Torque [lb in] 350 300 100 250 1950 3500 135 200 3000 1500 2500 psi 400 bar Drehmoment [Nm] 500 3 4 5 Flow [G/min] 9 12 2000 1500 150 1000 70 1000 100 500 50 35 250 0 0 50 100 150 200 0 0 25 50 75 Drehzahl [1/min] TE 0370 2 5 25 30 50 40 125 150 175 200 500 250 225 Speed [Rpm] Schluckstrom [L/min] 20 10 15 100 0.5 1 2 75 57 700 3 4 5 7 Flow [G/min] 12 9 15 US 20 6000 5500 5000 4500 500 4000 90 200 1825 3500 3000 psi 300 Torque [lb in] 125 400 bar Drehmoment [Nm] 600 2500 1325 2000 1500 70 1000 1000 100 500 0 0 20 40 60 80 100 120 140 160 180 200 35 220 0 0 20 40 60 80 100 120 140 160 180 500 220 200 Speed [Rpm] Drehzahl [1/min] TE 0390 Schluckstrom [L/min] 2 5 10 15 20 25 30 50 40 57 0.5 1 2 3 6000 75 650 5 7 US Flow [G/min] 12 9 15 20 5500 600 5000 550 4500 Torque [lb in] 400 85 250 bar 350 300 70 200 1750 4000 120 450 3500 3000 1250 2500 2000 psi 500 Drehmoment [Nm] 4 1000 1500 150 1000 100 500 50 0 0 20 40 60 80 100 120 140 160 180 0 35 200 0 40 60 80 100 120 140 160 180 500 200 Speed [Rpm] Drehzahl [1/min] Cont. 20 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 004 TE.indd, js 53 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série Flange Mount / Standardgehaeuse Monture à bride(s) / Montaje de brida Wheel Mount / Radnabengehaeuse Monture à roue / Montaje de rueda Side Load - N (lbs) Side Load - N (lbs) 142,336 (16,000) 124,544 (14,000) 142,336 (16,000) Max Load Curve 124,544 (14,000) 107,952 (12,000) 107,952 (12,000) 88,960 (10,000) 88,960 (10,000) 35,584 (8,000) 35,584 (8,000) 26,688 (6,000) 26,688 (6,000) 17,792 (4,000) 17,792 (4,000) Dynamic Load Curve Max Load Curve Dynamic Load Curve 8,896 (2,000) 8,896 (2,000) 0 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Distance from Mounting Face - mm (in) Motor Image Not To Scale The dynamic side load curve is based on unidirectional steady state loads for L10 bearing life at 3 x 106 revolutions. Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 3 x 106 Umdrehungen kalkuliert. La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 3 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 3 x 106 revoluciones. Distance from Mounting Face - mm (in) Motor Image Not To Scale The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. 004 TE.indd, js 54 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série Equation to Calculate the Expected Radial Bearing Life Gelichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 2.5 x 106 60 x S {FF } 3.33 a b Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min-1 L = Life In Hours / Lebensdauer in Stunden Fa = Allowable side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281 004 TE.indd, js 55 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série Code: AM SAE A 2-Bolt, Manifold “L” 48.3 (1.90) 2.55 (.10) 48.26 (1.900) 14.2 (.56) 4 x 5/16-18 UNC 12.7 (.50) 48.27 (1.94) 63.50 (2.500) A ø 95.5 (3.76) A ø 82.50 / 82.55 (3.248 / 3.250) 45.7 (1.8) A 127.3 (5.01) B B 2 x 31.75 (1.250) A 28.56 (1.125) 2 x 14.28 (.562) 13.69 / 13.28 (.539 / .523) ø 106.38 (4.188) Code AM disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 7.58 7.80 8.07 8.35 8.66 8.80 Poids/Peso (lb) (13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5) (16.2) (16.7) (17.2) (17.8) (18.4) (19.1) (19.4) Length "L" mm 136 138 141 144 147 154 160 166 173 179 185 192 200 205 "L" (in) (5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) (7.88) (8.04) Code: AP SAE A 2-Bolt, 1/2-14 NPTF Pipe “L” 48.3 (1.90) 2.55 (.10) 48.26 (1.900) 14.2 (.56) 48.27 (1.94) 45.72 (1.800) A A ø 82.50 / 82.55 (3.248 / 3.250) ø 95.5 (3.76) 127.3 (5.01) B B 2 x 22.86 (.900) 13.69 / 13.28 (.539 / .523) 1/2-14 NPTF ø 106.38 (4.188) Code AP disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 7.58 7.80 8.07 8.35 8.66 8.80 Poids/Peso (lb) (13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5) (16.2) (16.7) (17.2) (17.8) (18.4) (19.1) (19.4) Length "L" mm 136 138 141 144 147 154 160 166 173 179 185 192 200 205 "L" (in) (5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) (7.88) (8.04) English equivalents for metric specifications are shown in ( ). 004 TE.indd, js 56 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série Code: AS SAE A 2-Bolt, 7/8-14 SAE O-Ring “L” 48.3 (1.90) 2.55 (.10) 48.26 (1.900) 14.2 (.56) 48.27 (1.94) 45.72 (1.800) A A ø 82.50 / 82.55 (3.248 / 3.250) ø 95.5 (3.76) 127.3 (5.01) B B 2 x 22.86 (.900) 13.69 / 13.28 (.539 / .523) 7/8-14 SAE O-Ring ø 106.38 (4.188) Code AS disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 7.58 7.80 8.07 8.35 8.66 8.80 Poids/Peso (lb) (13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5) (16.2) (16.7) (17.2) (17.8) (18.4) (19.1) (19.4) Length "L" mm 136 138 141 144 147 154 160 166 173 179 185 192 200 205 "L" (in) (5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) (7.88) (8.04) Code: FP Magneto, 1/2-14 NPTF Pipe "L" 48.3 (1.90) 45˚ 48.26 (1.900) 2.55 (.10) 45.72 (1.800) A A ø 95.5 (3.76) 80 (3.118) ø 44.40 / 44.45 (1.748 / 1.750) B B 2 x 22.86 (.900) ø 82.55 (3.250) 1/2-14 NPTF 48.27 (1.94) 3/8-16 UNC Code FP disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 5.62 5.67 5.80 5.94 6.08 6.31 6.62 7.03 7.17 7.39 7.62 7.94 8.26 8.39 Poids/Peso (lb) (12.4) (12.5) (12.8) (13.1) (13.4) (13.9) (14.6) (15.5) (15.8) (16.3) (16.8) (17.5) (18.2) (18.5) Length "L" mm 136 138 141 144 147 154 160 166 173 179 185 192 200 205 "L" (in) (5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) (7.88) (8.04) English equivalents for metric specifications are shown in ( ). 004 TE.indd, js 57 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série Code: FS Magneto, 7/8-14 SAE O-Ring "L" 48.3 (1.90) 48.26 (1.900) 2.55 (.10) 45˚ 45.72 (1.800) A ø 95.5 (3.76) A 80.0 (3.118) ø 44.40 / 44.45 (1.748 / 1.750) B B 2 x 22.86 (.900) ø 82.55 (3.250) 7/8-14 SAE O-Ring 48.27 (1.94) 3/8-16 UNC Code FS disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 5.62 5.67 5.80 5.94 6.08 6.31 6.62 7.03 7.17 7.39 7.62 7.94 8.26 8.39 Poids/Peso (lb) (12.4) (12.5) (12.8) (13.1) (13.4) (13.9) (14.6) (15.5) (15.8) (16.3) (16.8) (17.5) (18.2) (18.5) Length "L" mm 136 138 141 144 147 154 160 166 173 179 185 192 200 205 "L" (in) (5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) (7.88) (8.04) English equivalents for metric specifications are shown in ( ). 004 TE.indd, js 58 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série Code: US Wheel Mount, 7/8-14 SAE O-Ring "L" 19.1 (.75) 36.83 (1.450) 31.75 (1.25) 19.1 (.75) 5.334 (.210) 3.449 (.1358) 25.4 (1.0) ø 49.20 (1.937) ø 95.25/95.15 (3.750/3.746) ø 91.56/93.35 (3.605/3.675) A 45˚ 58.4 (2.30) 130.2 (5.125) A 118.9 (4.680) ø 60.32/60.27 (2.374/2.372) B B 45.72 (1.800) ø 13.494 (17/32) 2 x 22.86 (.900) 7/8-14 SAE O-Ring 126.7 (4.99) Code US disp. 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 Weight/Gewicht kg 6.80 6.90 7.00 7.10 7.20 7.60 7.80 8.10 8.30 8.60 8.80 9.10 9.40 9.60 Poids/Peso (lb) (15.0) (15.2) (15.4) (15.6) (15.8) (16.7) (17.2) (17.9) (18.3) (19.0) (19.4) (20.0) (20.7) (21.2) Length "L" mm 107 109 112 115 118 125 131 137 144 150 156 163 171 176 "L" (in) (4.21) (4.27) (4.39) (4.52) (4.64) (4.89) (5.14) (5.39) (5.64) (5.89) (6.14) (6.39) (6.73) (6.89) English equivalents for metric specifications are shown in ( ). 004 TE.indd, js 59 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série Code U Code A Code F Code: 09 1" Straight with 0.38" Crosshole 44.7 (1.76) 73.9 (2.91) Code: 10 1" Keyed Code: 21 44.7 (1.76) 73.9 (2.91) 44.7 (1.76) 73.9 (2.91) 49.3 (1.94) 78.5 (3.09) Corrosion Resistant Code: 11 1" 6B Spline Code: 13 Long 1" Keyed English equivalents for metric specifications are shown in ( ). 004 TE.indd, js 60 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes Code: 09 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série ø 9.53 / 9.91 (.375 / .390) 1" Straight with 0.38" Crosshole 14.52 (.571) 13.51 (.531) ø 25.37 / 25.50 (.999 / 1.00) 38.6 (1.52) Code: 10 19.00 (.748) 1" Keyed 1/4 x 1 SAE J502 6.35/6.37 (.250/.251) Code: 21 Corrosion Resistant 28.30 (1.114) 27.64 (1.088) ø 25.37 / 25.40 (.999 / 1.00) 1/4-20 UNC 15.8 (.62) 38.6 (1.52) 6B SAE J499 38.6 (1.52) Code: 11 ø 25.32 (.997) 25.02 (.985) 1" 6B Spline 60o 6.27 (.246) 6.20 (.244) 1/4-20 UNC 15.8 (.62) 1.32 (.052) 1.17 (.046) 4.88 (.192) ø 21.54 (.848) 21.29 (.838) 1.24 (.049) 19.0 (.748) 1/4 x 1 SAE J502 ø 28.30 (1.114) 27.64 (1.088) 6.37 (.251) 6.35 (.250) 25.4 (1.00) MIN Code: 13 Long 1" Keyed 43.2 (1.700) 1.32 (.052) 1.17 (.046) ø 25.37 / 25.40 (.999 / 1.00) English equivalents for metric specifications are shown in ( ). 004 TE.indd, js 61 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série Code A Code U Code F Code: 25 1" Tapered 62.3 (2.45) 90.2 (3.55) 50.4 (1.98) 78.2 (3.08) Code: 26 25mm Keyed with 8mm Key English equivalents for metric specifications are shown in ( ). 004 TE.indd, js 62 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TE Series / Serie / Série 1/4x1 SAE J502 3/4x16 UNF Md= 240-300Nm (175-225 Ft Lbs) Code: 25 ø 25.37 (.999) 25.40 (1.00) 1" Tapered 6.37 (.251) 6.35 (.250) 3.0 (.118) 1:8 34.6 (1.36) 45.5 (1.793) Code: 26 8.000 (.3150) 7.964 (.3136) A8 x 7 x 32 mm ø25.015 (.9848) 25.002 (.9843) 25mm Keyed with 8mm Key M8 x 1.25 19 (.75) 27.7 (1.09) 28.3 (1.11) 43.0 (1.694) English equivalents for metric specifications are shown in ( ). 004 TE.indd, js 63 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Speed Sensor / Drehzahl-Sensor Compte-tours / Contagiri Code: FSAA* or FSAB LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Small Frame Motors US An Economical Sensor for Speed Readout This rugged, weather resistant design is ideal for industrial and mobile applications. Applications include salt/ sand/fertilizer spreader drives, conveyer drives and injection molder compression drives. The sensor is a halleffect type, which when externally powered outputs 30 square wave digital pulses per coupling shaft revolution. The connector is a user friendly universally available 4 pin polarized M12 connector allowing for simplified field service. The integrated design does not effect the side load capacity or performance of the torque motor. Dieser robuste, wetterfeste Drehzahlaufnehmer arbeitet nach dem Halleffekt. Es werden 30 Rechteckimpulse pro Abtriebswellenumdrehung erzeugt. Durch Erfassung der positiven und negativen Wellenflanken sind 60 Impulse pro Umdrehung möglich. Der Sensor führt zu keiner Leistungsbeschränkung des Motors. Die volle Radiallastkapazität bleibt erhalten. Un capteur economique pour mesure de la vitesse. Ce capteur robuste et resistant aux intemperies est a effet Hall. Alimente par une source externe, il fournit 30 ondes digitales carrees par tour. Par multiplication lelectronique on obient 60 pulsations par tour. Son montage ne modifie pas le couple ni la charge radiale du moteur qui le recoit. Este es un diseño de construcción reforzada, apto para uso a la intemperie e ideal para uso industrial y en equipos móviles. Entre sus aplicaciones, se puede mencionar esparcidores de sal, arena o fertilizantes, unidades motoras de transportadores y unidades motoras de compresión para moldeo a inyección. El sensor es del tipo de medio efecto, que al ser excitado externamente, genera 30 pulsos digitales de onda cuadrada por cada revolución del eje del acoplamiento. Utiliza un simple conector M12 polarizado tetrapolar, que es de uso común y facilita el mantenimiento en el lugar de instalación. El diseño integrado no afecta la capacidad de carga lateral ni la potencia del motor de torque. 44 (1.72) 71 (2.79) Maximum operating pressure 172 bar (2500 psi). US equivalents for metric specifications are shown in ( ). * Option code FSAA is with a single black coat of paint. * Code FSAA: Motor schwarz grundiert * Le code d’option montré correspond à une seule couche de peinture noire. * El código de la opción mostrado es con una sola capa de pintura negra. 005 Small Frame Options.indd, js 64 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Speed Sensor / Drehzahl-Sensor Compte-tours / Contagiri LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Small Frame Motors Operating voltage range Versorgungsspannung Gamme de tension de service Gama de voltaje de alimentacion 4.5...24 VDC Operating temperature Arbeitstemperatur Temperature de service Tempuratura de servicio -20° to 220° F -29°...104° C Operating frequency range Arbeitsfrequenz Gamme de frequences de service Gama de frecuencia de servicio 0...10 KHZ Max sink current Erforderlicher Laststrom Courant d‘affaissement maxi Corriente maxima de alimentacion 0 ... 20 mA (max.) Connection Anschluß Branchement Conexion 4 Pin Polarized (12mm) Sensor output Sonsorausgang Sortie du détecteur Salida del sensor 30 Pulses per revolution which can be doubled electronically 30 impulsions par revolution pouvant etre doublees electroniquement 30 pulsos por revolucion, que pueden duplicarse electronicamente Output is NPN Ausgang is NPN La sortie est NPN La salida es NPN 4 Pin Polarized M12 Connector (Male) Cable and “Pull Up” Resistor are not supplied by factory. Zubehör wie z.B. Kabel gehören nicht zum Lieferumfang Le câble et la résistance “Pull Up” ne sont pas fournis par l’usine. El cable y la resistencia de arranque no se suministran originalmente de fábrica. Open Collector "Pull Up" Resistor SENSOR Pull-up Resistor Value Formula Formel zur Ermittlung des Pull up-Widerstandes Formule de la valeur de resistance Pull-up Calculo de la resistance de carga PIN # 1 (+) 4.5 to 24 VDC PIN # 4 OUTPUT PIN # 3 (_) PIN # 2 NO CONNECTION (0.25 Watt, 5% de tol.) (0.25 Watt, Tol. 5%) (0.25 Watt 5% Tol.) (0.25 Watt, toll. 5%) Voltage / Spannung Courant d‘affaissement/ 4.5...24 VDC Voltaje Sink Current / Laststrom 0...20 mA Resistance / Corriente de alimentacion Status: Offstate / aus Etat: Arret / Estado: Inactivo (95% +V) +V = Resistor Widerstand Resistance Resistencia (k Ohm) Status: Onstate / ein Etat: Marche / Estado: Activo (max. 0.4 VDC) 0V 005 Small Frame Options.indd, js 65 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Crossover relief valve / Schockventil LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Valve anti-choc / Vavola di soprapressione Small Frame Motors Code: HAAA* or HAAB Specifications • • • • • • Spécifications US • Débit nominal – 75,7 litres/minute (20 gallons/minute) • Pressure de service maximale – ajustable jusqu’à 246 Rated flow — 20 gpm kg/cm2 (3 500 ppo2), préréglée à l’usine à 123 kg/cm2 (1 Max. Operating Pressure — adjustable up to 3500 psi, fac- 750 ppo2). tory preset at 1750 psi. • Pression de rajustage – 90% de la pression de consigne Reseat Pressure — 90% of set pressure • Gamme des températures de service – de – 40° C à 121° Operating Temperature Range: -40°F to 250°F C (-40° F à 250° F). Cartridge Material — All parts steel. All operating parts • Matériau de la cartouche – Entièrement en acier. Toutes les hardened steel. pièces de service en acier durci. Body Material — Steel • Matériau du corps – Acier Especificaciones técnicas Einsatzdaten • • • • • • • Caudal: 20 galones/minuto • Presión máxima de servicio: regulable hasta 3.500 libras/ pulg.2. Regulada de fábrica a 1.750 libras/pulg.2. • Presión de reasentamiento: 90% de la presión calibrada. • Gama de temperatura de servicio: - 40° F a 250° F • Material del cartucho: todas las partes son de acero. Todas las partes activas son de acero templado. • Material del cuerpo: acero Max. Fluß 76l/min. Max. Druck 240 bar (Voreinstellung 120 bar) Hysterese 90% des Öffnungsdrucks Betriebstemperatur – 40°C bis 115°C Ventil in Stahlausführung Code für Ausführung schwarz grundiert 85.3 (3.36) Max 47.5 (1.87) 69.9 (2.75) 50.8 (2.00) 23.9 (.94) 8.9 (.350) 55.6 (2.19) 7.9 (.31) 28.6 (1.125) 33.3 (1.31) 45.7 (1.800) 63.5 (2.500) 79.2 (3.12) 1/4" Hollow Hex Schraubenmoment 34 Nm (Bolt Torque 25 ft lb) Top View 2 x 9/16-18 SAE Str thd Port 14.3 (.562) 12.57 (.495) Dia. Rear View Bottom View Performance Curve 34.5 (1.36) Flow vs. Pressure 50.8 (2.00) Ref 275.8 (4000) Inlet Pressure- bar (PSI) 241.3 (3500) 15.5 (.61) Side View 206.8 (3000) Hydraulic Oil 100 SUS 172.4 (2500) 137.9 (2000) 103.4 (1500) 69.0 (1000) 34.5 (500) English equivalents for metric dimensions are shown in ( ). * Option code shown is with a single black coat of paint. * Motor schwarz grundiert * Le code d’option montré correspond à une seule couche de peinture noire. * El código de la opción mostrado es con una sola capa de pintura negra. 0 0 18.9 (5) 37.9 56.8 (10) (15) Flow L/min (G/min) 005 Small Frame Options.indd, js 66 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA 75.7 (20) Internal relief valve / Schockventil intern Soupape de sécurité interne / Regolatrice di pressione interna Code: BBCK, BBCN or BBCM LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Small Frame Motors US This integrated internal relief valve is used for fixed pressure settings. Internes Schockventil mit festen Einstelldrucken La soupape de sécurité interne s’utilise pour des valeurs de pression fixes. La valvula interna de alivio se utiliza para cablibraciones fijas de presion. A B "L" + 28.58 (1.125) "W" + 1.36 (3.0) A B Bestellschlüssel / Systéme de Commande / Ordering system / Sistema di ordinazione Pressure bar (psi) Option A Öffnungsdruck Opening pressure Tarage Soprapressione * * 83 (1200) 120 (1740) B * 140 (2030) Standard Length & Weights for TB Series on Pages 29-31 and TE Series on Pages 56-59. Längen/Gewichte TB Serie siehe Seiten 29-31, TE Serie Seiten 56-59. Longueurs et poids courants pour la série TB, voir les pages 29-31, et la série E, voir les pages 56-59. Los valores estándar de longitud y peso de la Serie TB se puede ver en las Páginas 29-31, y de la Serie E en las Páginas 56-59. English equivalents for metric specifications are shown in ( ). 005 Small Frame Options.indd, js 67 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Small Frame Motors Standard Options Code: AAAC Code: AAAC US Double Paint — Base coat of red oxine primer and finish coat of black paint for increased corrosion resistance. Zweischichtlackierung schwarz Code AAAF* or AABP Code AAAF* or AABP US Castle Nut — All motors ordered with Tapered shafts are equipped with patch locking nuts. If desired, a castle nut Kronenmutter Selbstsichernde Mutter wird ersetzt durch Kronenmutter may be specified. Code: AAAJ* or AAFG Code: AAAJ* or AAFG US Vespel™ Commutator Seal — Under conditions of high temperature, it is suggested that a vespel commutator seal be used. Code: AAAG* or AAAH US nicht ausreichender Schmierung. Code: AAAG* or AAAH Fluorocarbon — is available under various registered trademarks, including VITON™ (a registered trademark of DuPont), FLUOREL™ (a registered trademark of 3M) or FPM™ (a registered trademark of DuPont). Code: AABJ* or AABK Vespel™ / Kommutator Dichtung Für Anwendungen im höheren Temperaturbereich oder US Free Running Rotorset — The “free running rotorset” is a specially dimensioned rotorset that allows for smooth operation at low flows and low pressure. Volumetric efficiency can be affected. Fluorocarbon Dichtungen F ü r A n we n d u n g e n i m h ö h e r e n / n i e d r i g e r e n Temperaturenbereich oder speziellen Flüssigkeiten wird der Einsatz von Fluorcarbon Dichtungen empfohlen. Fluorocarbon ist bekannt unter verschiedenen eingetragenen Warenzeichen VITON™ - DuPont, Fluorel™ - 3M, FPM™ - DuPont Code: AABJ* or AABK Leichtläufer Rotorsatz Anlaufdruck < 5 bar * Option code shown is with a single black coat of paint. * Code: Motor schwarz grundiert * Le code d’option montré correspond à une seule couche de peinture noire. * El código de la opción mostrado es con una sola capa de pintura negra. 005 Small Frame Options.indd, js 68 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Small Frame Motors Standard Options Availability / Verfugbarkeit Code Painted Unpainted TC TB TE Lackiert UnLackiert US US US AAAC - US US US AAAF AABP Castle Nut / Kronenmutter US US US AAAG AAAH Fluorocarbon Seals / Fluorocarbon Dichtungen US US US AAAJ AAFG Vespel™ Commutator Seal / Vespel™ Kommutator Dichtung US US US AABJ* AABK* Free Running Rotorset / Leichtläufer-Rotorsatz US FSAA FSAB Speed Sensor / Drehzahl-Sensor US US - BBCN 140 Bar (2030 PSI) Internal Bidirectional Relief / Internes Schockventil US US - BBCK 120 Bar (1740 PSI) nternal Bidirectional Relief / Internes Schockventil US US - BBCM 83 Bar (1200 PSI) nternal Bidirectional Relief / Internes Schockventil US US HAAA HAAB Adjustable external Relief Valve / Schockventil (einstellbar) US Description / Beschreibung Double Paint / Zweischichten – Lackierung Consult factory for other positions and combinations. / Weitere Optionen nach Rücksprache verfügbar *Not applicable to 0365 or 0390 displacements. *Nicht verfugbar fur 0365 und 0390 005 Small Frame Options.indd, js 69 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information / Technische Information / Segni / Informacion Tecnica (2.5 – 24.0 in3/rev) 41 . . . 390 cm3/rev 14 Displacements 14 Schluckvolumen 14 Cylindrée 14 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Cont (to 2030 psi) . . .140 bar Int (to 2750 psi) . . .190 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite (to 20 gpm) . . . 75 lpm Maximum Speed Drehzahl Vitisse de rotation Maxi Velocidad Maxima (1024 rpm) 1024 rpm Maximum Torque Max Drehmoment Couple Maxi Torque Maximo Cont (4139 lb in) 467 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série The Ultimate in Performance from a Medium Frame Motor Parker’s TJ Series motor provides all that could be expected of a general purpose motor and more. Patented 60:40 spline geometry provides drivetrain strength for severe applications. Roller vanes and sealed orbit commutation assure high volumetric efficiency and smooth slow speed operation. Cooling fluid flow across splines and seals mean long, trouble-free life. Int (5728 lb in) 648 Nm (to 3150 lb) . . . 14000 N 006 TJ.indd, js 70 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l De ndré luck acem sp e v olu ent a me Ma zam i n e x Ma . spe ntos ed x. Vit Dre @ M is h Ve se d zahl ax. i loc e r Int nte ida ota erm rm it t d m t io it Ma ax n m tiere ent fl x. im ax nd o Ma oil aa i er w flo x Be ca Dé . Sch w t rie ud b lu al b: Ca it d´h cks int t ud e r u rm al ile m om it e Ma Ma nte x im a x i xd ma o Ma iffe d x im eA x r o ce Ch . Dru entia i u te c l Pr te de kgef pres es ä ion pre lle sure dif ssio Ma e re n m x nc Ma . sup ia l a x i x. ply ma E Pr p i n xim r e g e a Pr ssio ang ssu es r s n e ion ma dru c x ma i e k Ma xim ntr x a d ée Ma . torq ea x. u e lim Co Dre en up hm tac To le m om ion rqu e a nt e M xi ax Ma im x o Ma . per for x. L m Pu is eist anc Ma sanc unga e xim e d bg o r e s abe Mi en ort n. dim ie Mi star iet max n. t in o i g Co Anl t up au orq u f l To e m mo e rqu m e m in. fo ent ini urn mo i a de u dé a rr m an anr qu e age LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série Motor Series TJ cm3/rev in3/rev rev/min cont / int* l/min g/min cont / int* bar psi TJ 0045 41 2.5 1024 34 9 42 11 140 2000 190 2750 200 2900 71 624 99 876 10.4 13.9 46 411 64 565 TJ 0050 49 3.0 1020 34 9 50 13 140 2000 190 2750 200 2900 90 796 127 1120 12.8 17.2 72 637 98 871 TJ 0065 65 4.0 877 45 12 57 15 140 2000 190 2750 200 2900 125 1106 176 1558 14.7 19.8 100 885 137 1211 TJ 0080 82 5.0 695 45 12 57 15 140 2000 190 2750 200 2900 160 1416 220 1947 17.3 23.2 128 1133 171 1515 TJ 0100 98 6.0 582 45 12 57 15 140 2000 190 2750 200 2900 190 1682 264 2337 17.4 23.4 152 1345 205 1819 TJ 0130 130 8.0 438 45 12 57 15 140 2000 190 2750 200 2900 255 2257 352 3116 17.3 23.2 204 1806 274 2423 TJ 0165 163 10.0 348 45 12 57 15 140 2000 190 2750 200 2900 310 2744 436 3846 17.0 22.8 248 2195 338 2992 TJ 0195 195 11.9 292 45 12 57 15 140 2030 190 2750 200 2900 390 3452 528 4673 17.4 23.4 312 2762 411 3637 TJ 0230 228 13.9 328 57 15 75 20 120 1750 165 2400 200 2900 380 3363 514 4554 17.7 23.8 304 2691 411 3637 TJ 0260 260 15.9 287 57 15 75 20 110 1650 155 2250 200 2900 400 3540 550 4870 16.7 22.4 320 2832 449 3977 TJ 0295 293 17.9 256 57 15 75 20 100 1550 145 2100 200 2900 428 3784 582 5180 15.7 21.0 328 2903 445 3939 TJ 0330 328 20.0 228 57 15 75 20 100 1550 135 1960 200 2900 443 3926 600 5312 14.8 19.8 344 3045 453 4014 TJ 0365 370 22.6 203 57 15 75 20 95 1325 125 1825 200 2900 467 4133 648 5728 13.6 18.2 373 3301 477 4223 TJ 0390 392 24.0 191 57 15 75 20 85 1250 120 1740 200 2900 445 3935 628 5562 12.5 16.8 348 3080 462 4090 Performance data based on testing using 10W40 oil with a viscosity of 43,1 cSt. (200 SUS) at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. max bar psi cont / int* Nm lb-in max KW HP cont / int* Nm lb-in * Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. 006 TJ.indd, js 71 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TJ Series XXXX Displacement Schluckvolumen Cylindrée Desplazamiento Code cm3/U / cm3/rev cm3/tr / cm3/giro 0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390 41 / 2.5 49 / 3.0 65 / 4.0 82 / 5.0 98 / 6.0 130 / 8.0 163 / 10.0 195 / 11.9 228 / 13.9 260 / 15.9 293 / 17.9 328 / 20.0 370 / 22.6 392 / 24.0 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série US Mounting/Ports Gehäuse/ Carter/Plan de raccordement Montaje/Lumbreras 08 0 XXXX Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion Options Opciones Code Mounting/Porting Wheel Mount, 7/8-14 SAE US Code Shaft 1 1/4" Tapered* 08 *See installation instructions. Code 0 Rotation Standard Code No Paint No lackiert Black Paint Schwarz lackiert AAAB AAAA Consult factory for other available options, configurations ordering codes and lead times. 006 TJ.indd, js 72 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série TJ 0045 2 US 10 5 Schluckstrom [L/min] 20 30 25 15 34 2 0.5 1 42 120 3 Flow [G/min] 5 7 4 9 11 1100 1000 100 900 190 2750 140 60 100 40 600 2000 psi Torque [lb in] 700 bar Drehmoment [Nm] 800 80 500 1500 400 300 70 100 35 0 1000 200 20 0 100 200 300 400 500 600 700 800 900 500 0 1000 0 100 200 300 400 500 600 700 800 900 1000 Speed [Rpm] Drehzahl [1/min] TJ 0050 Schluckstrom [L/min] 24 8 11 15 19 34 27 0.5 1 2 1200 50 140 3 US Flow [G/min] 7 9 5 4 13 1100 120 1000 2750 900 140 60 100 40 700 2000 600 psi Torque [lb in] 800 80 bar Drehmoment [Nm] 190 100 500 1500 400 300 70 1000 200 20 100 500 35 0 0 100 200 300 400 500 600 700 800 900 0 1000 0 100 200 300 400 500 600 Speed [Rpm] Drehzahl [1/min] 700 800 900 1000 TJ 0065 Schluckstrom [L/min] 180 2 5 10 15 20 25 30 40 45 0.5 1 2 57 4 7 5 Flow [G/min] 9 US 12 15 1750 160 1500 190 140 2750 1250 Torque [lb in] 120 1000 80 100 60 2000 psi 140 100 bar Drehmoment [Nm] 3 750 1500 500 40 70 1000 250 20 35 0 0 100 200 300 400 500 600 700 0 Drehzahl [1/min] Cont. 500 0 800 850 100 200 300 400 500 Speed [Rpm] 600 700 800 850 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 006 TJ.indd, js 73 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos TJ 0080 2 5 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série Schluckstrom [L/min] 15 10 20 30 25 40 0.5 1 2 3 2000 57 45 220 4 5 7 Flow [G/min] 9 US 12 15 1800 200 190 2750 1600 160 1400 140 100 100 80 bar 120 1200 2000 1000 psi 140 Torque [lb in] Drehmoment [Nm] 180 1500 800 600 60 70 1000 400 40 200 20 35 500 0 0 0 100 200 300 400 500 600 0 700 100 200 300 400 500 600 700 Speed [Rpm] Drehzahl [1/min] TJ 0100 Schluckstrom [L/min] 2 5 10 275 20 15 25 40 30 45 0.5 1 2 3 2400 57 7 Flow [G/min] 9 US 12 15 2200 250 2750 2000 190 225 1800 200 1600 175 150 125 100 100 75 2000 1400 1200 psi Torque [lb in] 140 bar Drehmoment [Nm] 5 4 1000 1500 800 600 70 50 1000 400 25 200 35 0 0 100 200 300 Drehzahl [1/min] 400 500 500 0 600 0 100 200 300 400 500 600 Speed [Rpm] TJ 0130 Flow [G/min] 9 7 Schluckstrom [L/min] 400 2 5 10 15 20 25 40 30 45 0.5 1 2 57 4 5 US 12 15 3500 350 3000 2750 190 300 2500 140 200 150 100 2000 2000 psi Torque [lb in] 250 bar Drehmoment [Nm] 3 1500 1500 1000 100 1000 70 500 50 500 35 0 0 0 50 100 150 200 250 300 350 400 0 450 Drehzahl [1/min] Cont. 50 100 150 200 250 Speed [Rpm] 300 350 400 450 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 006 TJ.indd, js 74 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série TJ 0165 US Schluckstrom [L/min] 2 5 500 10 15 20 25 30 40 45 0.5 1 2 4000 57 4 5 12 15 3600 450 2750 400 3200 190 2800 2000 2400 Torque [lb in] 300 140 250 200 100 2000 1500 1600 psi 350 bar Drehmoment [Nm] 3 Flow [G/min] 9 7 1200 150 1000 70 100 800 400 50 500 35 0 0 0 50 100 150 200 250 300 0 350 50 100 150 Drehzahl [1/min] 200 250 300 350 Speed [Rpm] TJ 0195 Schluckstrom [L/min] 2 5 10 15 20 25 40 30 57 0.5 1 2 5000 550 500 3 4 7 5 9 12 15 4500 190 450 2750 4000 400 3500 350 300 250 100 200 3000 2000 2500 psi Torque [lb in] 140 bar Drehmoment [Nm] US Flow [G/min] 45 2000 1500 1500 150 70 1000 1000 100 50 500 35 0 0 50 100 150 200 250 500 0 300 0 50 100 Drehzahl [1/min] 150 Speed [Rpm] 200 250 300 TJ 0230 Schluckstrom [L/min] 550 0.5 1 2 5000 500 4500 10 15 20 25 30 40 50 57 75 4 5 7 US Flow [G/min] 12 9 15 20 4000 400 165 Torque [lb in] 140 300 120 250 100 200 2400 3500 350 bar Drehmoment [Nm] 450 3 3000 2000 2500 1750 2000 psi 2 5 1500 1500 150 1000 70 100 1000 500 50 0 0 50 100 150 200 250 300 0 35 350 0 Drehzahl [1/min] Cont. 50 100 150 200 250 300 500 350 Speed [Rpm] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 006 TJ.indd, js 75 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série TJ 0260 US Schluckstrom [L/min] 2 5 600 10 15 20 25 30 50 40 Flow [G/min] 3 0.5 1 2 75 57 4 7 5 12 9 15 20 5000 550 4500 500 4000 2250 3500 350 Torque [lb in] 155 300 250 115 200 100 3000 1650 2500 psi 400 bar Drehmoment [Nm] 450 1500 2000 1500 150 1000 1000 100 70 500 50 0 50 100 150 Drehzahl [1/min] 200 250 500 300 0 35 300 0 0 50 100 150 Speed [Rpm] 200 250 TJ 0295 2 5 10 15 20 25 Schluckstrom [L/min] 50 40 57 30 0.5 1 2 3 4 75 600 5500 550 5000 500 4500 7 9 US Flow [G/min] 12 15 20 4000 145 400 2100 3500 Torque [lb in] 350 105 250 psi 3000 300 1550 2500 bar Drehmoment [Nm] 450 5 2000 200 1500 150 70 1000 1000 100 500 50 0 0 25 50 75 100 125 150 175 200 225 250 35 275 500 275 0 0 25 50 75 100 125 150 175 200 225 250 Speed [Rpm] Drehzahl [1/min] TJ 0330 Schluckstrom [L/min] 2 5 10 15 20 25 30 40 50 57 0.5 1 2 75 650 5500 600 5000 550 4500 7 9 Flow [G/min] 12 US 15 20 4000 450 Torque [lb in] 350 300 100 250 1950 3500 135 200 3000 1500 2500 psi 400 bar Drehmoment [Nm] 500 3 4 5 2000 1500 150 1000 70 1000 100 500 50 0 0 50 100 150 200 35 250 0 0 Drehzahl [1/min] Cont. 25 50 75 100 125 150 175 200 225 500 250 Speed [Rpm] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 006 TJ.indd, js 76 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos US TJ 0370 2 5 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série Schluckstrom [L/min] 20 10 15 25 30 50 40 0.5 1 2 75 57 700 3 4 5 7 Flow [G/min] 12 9 15 20 6000 5500 5000 4500 500 4000 90 200 1825 3500 3000 psi 300 Torque [lb in] 125 400 bar Drehmoment [Nm] 600 2500 1325 2000 1500 70 1000 1000 100 500 0 0 20 40 60 80 100 120 140 160 180 200 35 220 0 0 20 40 60 80 100 120 140 160 180 500 220 200 Speed [Rpm] Drehzahl [1/min] TJ 0390 Schluckstrom [L/min] 2 5 10 15 20 25 30 50 40 57 0.5 1 2 3 6000 75 650 5 7 US Flow [G/min] 12 9 15 20 5500 600 5000 550 4500 450 Torque [lb in] 400 85 250 bar 350 300 70 200 1750 4000 120 3500 3000 1250 2500 2000 psi 500 Drehmoment [Nm] 4 1000 1500 150 1000 100 500 50 0 0 20 40 60 80 100 120 140 160 180 0 35 200 0 40 60 80 100 120 140 160 180 500 200 Speed [Rpm] Drehzahl [1/min] Cont. 20 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 6 segundos por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54°C. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 006 TJ.indd, js 77 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Wheel Mount / Radnabengehaeuse Monture à roue / Montaje de rueda 66723 (15000) Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. Max Load Curve Radial Load - N (lbs) 44482 (10000) La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. The dynamic side load curve is based on uni-directional steady state loads for L10 bearing life at 3 x 106 revolutions. 22241 (5000) Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 3 x 106 Umdrehungen kalkuliert. Dynamic Load Curve 0 0 25.4 (1) 50.8 (2) 76.2 (3) 101.6 (4) 127 (5) 152.4 (6) Distance from Mounting Face mm (in) Motor Image Not To Scale Equation to Calculate the Expected Radial Bearing Life Gelichung zur Ermittlung der Lagerlebensdauer La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 3 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 3 x 106 revoluciones. Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 3 x 106 60 x S {FF } 3.33 a b Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min-1 L = Life In Hours / Lebensdauer in Stunden Fa = Dynamic side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281 006 TJ.indd, js 78 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série Code: US Wheel Mount, 7/8-14 SAE O-Ring "L" ø 4.06 (.16) 36.83 (1.45) 4.562 (.1796) 19.0 (.75) ø 126.97/126.95 (4.9988/4.9980) 12.4 (.488) 46.74 (1.84) ø 82.55/82.50 (3.249/3.248) A ø 95.25/95.15 (3.750/3.746) *To Port Spotface 63.83* 45˚ (2.513)* 50.8 (2.0) A 135.0 (5.31) ø 91.56 / 93.35 (3.605/3.675) B B 40.13 (1.58) Max ø 72.90 (2.87) as cast 7/8-14 SAE O-Ring Code US disp. 0045 0050 0065 Weight/Gewicht kg 6.80 6.90 7.00 Poids/Peso (lb) (15.0) (15.2) (15.4) Length "L" mm 107 109 112 "L" (in) (4.21) (4.27) (4.39) 2 x 25.4 (1.0) 0080 0100 0130 0165 0195 7.10 7.20 7.60 7.80 8.10 (15.6) (15.8) (16.7) (17.2) (17.9) 115 118 125 131 137 (4.52) (4.64) (4.89) (5.14) (5.39) 147.6 (5.81) 13.5 (17/32) 0230 0260 0295 8.30 8.60 8.80 (18.3) (19.0) (19.4) 144 150 156 (5.64) (5.89) (6.14) 0330 0365 0390 9.10 9.40 9.60 (20.0) (20.7) (21.2) 163 171 176 (6.39) (6.73) (6.89) English equivalents for metric specifications are shown in ( ). 006 TJ.indd, js 79 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série Code U Code: 08 1 1/4" Tapered 106.9 (4.21) 5/16x1 SAE J502 1:8 Md: 407-542Nm (300-400 Ft Lb) 7.96/7.94 (.313/.312) ø 31.88/31.50 (1.25/1.24) 3.5/3.1 (.13/.12) 35 (1.378) 1-20UNEF 19 (.748) English equivalents for metric specifications are shown in ( ). 006 TJ.indd, js 80 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Notes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TJ Series / Serie / Série 006 TJ.indd, js 81 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Medium Frame Motors Standard Options Code: AAAC Code: AAAC US Double Paint — Base coat of red oxide primer and finish coat of black paint for increased corrosion resistance. Zweischichtlackierung schwarz Code AAAF* or AABP Code AAAF* or AABP US Castle Nut — All motors ordered with Tapered shafts are equipped with patch locking nuts. If desired, a castle nut may be specified. Kronenmutter Selbstsichernde Mutter wird ersetzt durch Kronenmutter Code: AAAJ* or AAFG US Code: AAAJ* or AAFG Vespel™ Commutator Seal — Under conditions of high temperature, it is suggested that a vespel commutator seal be used to optimize volumetric efficiency. Vespel™ / Kommutator Dichtung Für Anwendungen im höheren Temperaturbereich oder nicht ausreichender Schmierung. Code: AAAG* or AAAH US Fluorocarbon shaft and section seals is available under various registered trademarks, including VITON™ (a registered trademark of DuPont), FLUOREL™ (a registered trademark of 3M) or FPM™ (a registered trademark of DuPont). Code: AABJ* or AABK US Code: AAAG* or AAAH Fluorocarbon Dichtungen Für Anwendungen im höheren/niedrigeren Temperaturbereich oder speziellen Flüssigkeiten wird der Einsatz von Fluorcarbon Dichtungen empfohlen. Fluorocarbon ist bekannt unter verschiedenen eingetragenen Warenzeichen VITON™ - DuPont, Fluorel™ - 3M, FPM™ - DuPont Free Running Rotorset — The “free running rotorset” is a specially dimensioned rotorset that allows for smooth operation at low flows and low pressure. Volumetric efficiency can be affected. Code: AANM* Code: AABJ* or AABK Leichtläufer Rotorsatz Anlaufdruck < 5 bar US Code: AANM* Seal Saver — Seal saver is a metal disc that presses onto the motor shaft, covering the dirt and water (D&W) seal. It’s purpose is to aid in preventing external contamination from damaging the D&W seal. Versiegelungsschutz — Der Versiegelungsschutz besteht aus einer Metallscheibe, die gegen die Antriebswelle druckt und damit Schmutz- und Wasserdichtung (D&W-Dichtung) abdeckt. Hierdurch soll einer Beschadigung der D&W-Dichtung auf Grund externer Verunreinigungen vorgebeugt werden. * Option code shown is with a single black coat of paint. * Motor schwarz grundiert * Le code d’option montré correspond à une seule couche de peinture noire. * El código de la opción mostrado es con una sola capa de pintura negra. 007 Medium Frame Options.indd, js 82 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Medium Frame Motors Standard Options Availability / Verfugbarkeit Code Painted Unpainted TJ Lackiert Unlackiert Description / Beschreibung US AAAC - US AAAF AABP Castle Nut / Kronenmutter US AAAG AAAH Fluorocarbon Seals / Fluorocarbon Dichtungen US AAAJ AAFG Vespel™ Commutator Seal / Vespel™ Kommutator Dichtung US AABJ* AABK* Free Running Rotorset / Leichtläufer-Rotorsatz Double Paint / Zweischichten – Lackierung Consult factory for other positions and combinations. / Weitere Optionen nach Rücksprache verfügbar * Not applicable to TJ 0365 or TJ 0390 displacements. * Nicht verfugbar fur TJ 0365 and TJ 0390. Consult factory for other available options, configurations ordering codes and lead times. 007 Medium Frame Options.indd, js 83 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica (4.9 - 29.1 in3/rev) 81 . . . 477 cm3/rev 11 Displacements 11 Schluckvolumen 11 Cylindrée 11 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Cont. (to 3000 psi) . . . 207 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque MaxDrehmoment Couple Torque Maximo Int. (to 4000 psi) . . . 276 bar LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série A Tough Motor for Tough Applications Sturdy construction throughout makes Parker’s TF Series motors suitable for the most severe applications. The powertrain uses patented 60:40 spline geometry for strength. All splines are constantly flushed with cool fluid for durability. Roller vanes and sealed commutation assure high volumetric efficiency, smooth low speed operation and extended life. Shaft seals can withstand full system pressure and are washed in cool fluid for long life. (to 25 gpm) . . . 95 lpm (749 rpm) 749 rpm Cont. (6027 lb in) 681 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral Int. (8106 lb in) 916 Nm (to 3597 lb) . . . 16000 N 008 TF.indd, js 84 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l Cil ndré luck acem ind e vo lum ent ra t Ma a en x Ma . spe ed x. Vit Dre @ M e h Ve sse d zahl ax. i loc e r Inte nte id ot rm rm Ma ad m ation ittie itten ax x. im max rend t flow Ma oil aa er i x. flow Be ca Dé Sch t rie u bit d lu al b: Po d´h cks i n t t r ta e r u rm ta ile m om it e ma Ma nte x axi x. ma d Ma iff x im er x o Ch . Dru enti a u c l Pr te de kgef pres es ä ion pre lle sure dif ssio Ma e re n m x nc Ma . sup ia l a x i x. ply ma E Pr p i n xim r es ga e a Pr sion ngs ssur es e ion max druc ma i en k Ma x im t ré x ad e Ma . torq ea x. u e lim Co Dre en up hm tac To le m om ion rqu e a nt e M xi ax Ma im x o Ma . per for x. L m Pu is eist anc Ma sanc unga e xim e d bg o r e s abe Mi en ort n. dim ie Mi star ien max n. t in to i g Co Anl t up au orq u f l To e m mo e rqu m e m in. fo ent ini urn mo i a de u dé a rr m an anr qu e age LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série Motor Series TF cm3/rev in3/rev rev/min cont / int* l/min g/min cont / int* bar psi max bar psi cont / int* Nm lb-in max KW HP cont / int* Nm lb-in TF 0080 81 4.9 693 46 12 57 15 207 3000 276 4000 300 4350 220 1948 296 2621 21.5 28.8 158 1401 205 1811 TF 0100 100 6.1 749 57 15 76 20 155 2250 241 3500 300 4350 197 1746 318 2813 24.9 33.4 148 1309 243 2155 TF 0130 128 7.8 583 57 15 76 20 138 2000 207 3000 300 4350 229 2031 356 3148 21.7 29.1 180 1596 278 2460 TF 0140 141 8.6 530 57 15 76 20 138 2000 207 3000 300 4350 254 2248 393 3477 21.8 29.2 196 1739 308 2728 TF 0170 169 10.3 444 57 15 76 20 138 2000 207 3000 300 4350 317 2808 489 4324 22.7 30.5 243 2152 385 3404 TF 0195 197 12.0 381 57 15 76 20 138 2000 207 3000 300 4350 364 3222 562 4971 22.4 30.1 302 2671 468 4142 TF 0240 238 14.5 394 76 20 95 25 138 2000 207 3000 300 4350 427 3782 670 5928 27.7 37.1 366 3242 572 5058 TF 0280 280 17.1 334 76 20 95 25 138 2000 207 3000 300 4350 509 4502 794 7029 27.8 37.3 438 3876 672 5946 TF 0360 364 22.2 258 76 20 95 25 130 1880 190 2750 300 4350 594 5257 880 7788 20.0 26.8 517 4575 779 6898 TF 0365 Clutch 364 22.2 258 76 20 95 25 97 1400 152 2200 300 4350 437 3871 740 6456 20.0 26.8 398 3521 650 5749 TF 0405 405 24.7 231 76 20 95 25 128 1850 172 2750 300 4350 655 5800 916 8106 22.1 29.7 575 5091 789 6978 TF 0475 477 29.1 195 76 20 95 25 113 1645 138 2000 300 4350 681 6027 851 7528 17.4 23.3 603 5334 740 6548 Performance data based on testing using 10W40 oil with a viscos- * Intermittent operation rating applies to 10% of every minute. ity of 43.1 cSt (200 SUS) at 54° C (130° F.) Performance data is Intermittierende Werte maximal 10% von jeder Betriebsminute. typical. Actual data may vary slightly from one production motor to Fonctionnement interm. 10% max. de chaque minute d`utilisation. another. Capacidad de funcionamiento intermitente valida para 10% por Les donnes sur les performances sont basees sur des tests cada minuto. utilisant de l'huile 10W40 d'une viscosite de 200 SUS a 54oC (130oF). Ces donnees correspondent a des situations typiques. Les donnes reelles peuvent varier legerement d'un moteur de production a l'autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54oC (130oF). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 008 TF.indd, js 85 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TF Series Code 0080 0100 0130 0140 0170 0195 0240 0280 0360 0405 0475 XXXX LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série XX XX Displacement Mounting/Ports Schluckvolumen Gehäuse/Anschluß Cylindrée Carter/Plan de raccordement Desplazamiento Montaje/Lumbreras Shaft Welle Arbre Eje cm3/U cm3/tr cm3/giro cu in3/rev 81 100 128 141 169 197 238 280 364 405 477 / / / / / / / / / / / 4.9 6.1 7.8 8.6 10.3 11.9 14.5 17.1 22.2 24.7 29.1 0 XXXX Rotation Drehrichtung Direction de rotation Rotacion Options Opciones Code Rotation Code Code Shaft Standard 1" 6B Spline Mounting/Ports 0 01* SAE "A” 2 Bolt, ISO 6149 M22 x 1.5 1" Keyed AH 02* SAE "A” 2 Bolt, 5/16-18 UNC Manifold1 1 1/4” Keyed 03 AM 1 1/4” 14 Tooth Spline 05 SAE "A” 2 Bolt, 7/8-14 SAE 19 Tooth Spline AS 06 15 Tooth Spline SAE "B” 2 Bolt, 7/8-14 SAE 07 BS 1 1/4” Tapered 08 Wheel, Front Brake Nose, 7/8-14 SAE LS Magneto, 7/8-14 SAE Code AAAB MS AAAA Options No Paint No lackiert Black Paint Schwarz lackiert Wheel,Standard, 7/8-14 SAE US For other available options, see pages 182-187. * Abtriebswelle Ø 25mm Max. torque cont./int. Arbre Couple maxi cont./int. 6B SAE Eje de acoplamiento } Max. Moment cont./int. Coupling shaft Ø 1 inch Coppia max cont./int. 450/550 Nm 008 TF.indd, js 86 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série TF 0080 Schluckstrom [L/min] 15 25 20 30 46 40 0.5 2 2750 57 50 350 3 5 4 Flow [G/min] 9 7 12 US 15 4000 2500 2250 280 250 Torque [lb/in] 200 150 140 100 2500 1500 1250 2000 1000 1500 750 100 1000 500 70 50 3000 1750 210 170 3500 2000 240 bar Drehmoment [Nm] 300 250 35 psi 2 5 10 500 0 0 0 100 200 300 400 500 600 0 700 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 Speed [Rpm] Drehzahl [1/min] TF 0100 2 5 10 20 15 Schluckstrom [L/min] 40 50 57 60 25 30 .5 1 2 3 4 3000 76 350 5 Flow [G/min] 12 9 7 15 US 20 3500 300 240 250 210 200 170 150 150 140 100 100 2500 Torque [lb/in] 2500 2000 1000 50 70 500 35 0 100 200 300 400 500 600 700 1500 1000 500 0 0 psi 2250 1500 bar Drehmoment [Nm] 3000 2000 0 800 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 Speed [Rpm] Drehzahl [1/min] TF 0130 Flow [G/min] Schluckstrom [L/min] 2 5 10 15 20 25 30 50 40 57 60 76 400 3500 4 5 7 9 12 US 15 20 3000 210 300 3000 2500 2500 140 200 100 2000 2000 psi Torque [lb/in] 170 bar Drehmoment [Nm] .5 1 2 3 1500 1500 1000 100 70 1000 500 500 35 0 0 0 100 200 300 400 500 0 600 Drehzahl [1/min] Cont. 100 200 300 Speed [Rpm] 400 500 600 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Leistugsdaten sind gemessen mit SAE 10W40 bei einer Viskositat von 43,1 Cst beo 54°C. Geringfugige Abweichungen von den Katalogerten sond moglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 008 TF.indd, js 87 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série TF 0140 Flow [G/min] Schluckstrom [L/min] 2 5 10 15 20 30 25 40 50 57 60 76 4000 450 .5 1 2 3 5 4 9 7 15 12 US 20 3500 400 210 3000 3000 Torque [lb/in] 170 250 140 200 2500 2500 2000 2000 psi 300 bar Drehmoment [Nm] 350 1500 1500 100 150 1000 100 1000 70 500 50 35 500 0 0 0 0 50 100 150 200 250 300 Drehzahl [1/min] 350 400 450 500 100 200 550 300 400 500 600 Speed [Rpm] TF 0170 2 5 10 15 20 25 30 Schluckstrom [L/min] 40 50 Flow [G/min] 57 60 76 0.5 2 3 4 5 5000 550 500 7 12 9 15 US 20 4500 210 4000 3000 3500 300 Torque [lb/in] 170 350 140 bar Drehmoment [Nm] 400 250 200 100 2500 3000 2500 2000 2000 1500 1500 150 psi 450 70 100 1000 50 1000 500 35 500 0 0 50 100 150 200 250 300 350 400 0 450 0 50 100 150 200 250 Speed [Rpm] Drehzahl [1/min] 300 350 400 450 500 TF 0195 2 5 10 15 20 25 30 Flow [G/min] Schluckstrom [L/min] 57 60 40 50 76 0.5 1 2 3 5500 600 7 9 12 US 15 20 3000 4500 4000 170 400 2500 140 300 100 200 70 1500 2000 1000 1000 500 35 0 50 100 150 200 250 300 350 500 0 400 0 Drehzahl [1/min] Cont. 2000 2500 1500 100 0 3000 psi Torque [lb/in] 3500 bar Drehmoment [Nm] 5 5000 210 500 4 50 100 150 200 Speed [Rpm] 250 300 350 400 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 10W40 bei einer Viskositat von 43,1 Cst beo 54°C. Geringfugige Abweichungen von den Katalogerten sond moglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 008 TF.indd, js 88 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série TF 0240 2 5 10 20 30 Schluckstrom [L/min] 40 50 60 70 76 80 0.5 1 2 3 4 5 6500 90 95 800 7 9 Flow [G/min] 12 15 20 US 25 6000 700 5500 600 3000 5000 210 300 3500 2000 3000 psi 140 Torque [lb/in] 400 2500 4000 170 bar Drehmoment [Nm] 4500 500 2500 1500 2000 100 200 1500 70 1000 1000 100 500 35 0 0 50 100 150 200 250 300 350 500 0 0 400 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 Speed [Rpm] Drehzahl [1/min] TF 0280 Schluckstrom [L/min] 2 5 10 20 30 40 50 70 76 80 60 .5 1 2 3 4 5 8000 90 95 900 800 9 Flow [G/min] 15 12 20 US 25 7000 210 600 Torque [lb/in] 170 140 300 bar 500 400 3000 6000 5000 2500 4000 2000 psi 700 Drehmoment [Nm] 7 3000 1500 100 2000 200 1000 70 1000 100 500 35 0 0 0 50 100 150 200 250 300 0 350 50 100 150 200 250 300 350 Speed [Rpm] Drehzahl [1/min] TF 0360 Flow [G/min] Schluckstrom [L/min] 2 5 10 20 30 40 50 60 70 76 80 90 95 9000 1000 7 9 12 15 20 US 25 8000 900 700 170 600 140 130 500 400 2750 7000 2500 6000 100 5000 2000 1850 psi 190 Torque [lb/in] 800 bar Drehmoment [Nm] .5 1 2 3 4 5 4000 1500 3000 300 2000 70 200 100 35 0 0 1000 1000 25 Cont. 50 75 100 125 150 Drehzahl [1/min] 175 200 225 250 500 0 0 275 25 50 75 100 125 150 175 200 225 250 275 Speed [Rpm] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Leistugsdaten sind gemessen mit SAE 10W40 bei einer Viskositat von 43,1 Cst beo 54°C. Geringfugige Abweichungen von den Katalogerten sond moglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 008 TF.indd, js 89 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série TF 0405 2 5 10 30 20 40 Schluckstrom [L/min] 50 70 76 80 60 Flow [G/min] 90 95 .5 1 2 3 4 5 9000 1000 900 12 9 US 15 20 25 8000 800 2500 7000 170 700 6000 100 400 2000 1850 4000 1500 psi 500 5000 Torque [lb/in] 140 130 600 bar Drehmoment [Nm] 7 3000 300 70 1000 2000 200 1000 100 500 35 0 0 0 25 50 75 100 125 150 175 200 225 0 250 25 50 75 100 125 150 175 200 225 250 25 US Speed [Rpm] Drehzahl [1/min] TF 0475 2 5 10 20 30 Schluckstrom [L/min] 40 50 60 70 76 80 90 95 9000 7 9 Flow [G/min] 12 15 20 8000 900 800 7000 140 130 600 110 500 100 2000 Torque [lb/in] 700 bar Drehmoment [Nm] .5 1 2 3 4 5 400 300 6000 1850 5000 1645 1500 psi 1000 4000 3000 1000 70 2000 200 1000 100 500 35 0 0 0 20 40 60 80 100 120 Drehzahl [1/min] 140 160 180 0 200 20 40 60 80 100 Speed [Rpm] 120 140 160 180 200 TF 0365 Clutch Motor Schluckstrom [L/min] 1000 2 5 10 20 30 40 50 60 70 76 80 90 95 0.5 1 2 3 4 5 9000 900 Flow [G/min] 12 15 9 US 20 25 8000 800 7000 700 6000 2200 Torque [lb/in] 150 140 500 400 100 300 200 1500 1400 3000 1000 1000 0 50 100 150 200 250 35 300 500 0 0 50 100 150 200 250 300 Speed [Rpm] Drehzahl [1/min] Cont. 2000 4000 2000 70 100 0 5000 psi 600 bar Drehmoment [Nm] 7 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 10W40 bei einer Viskositat von 43,1 Cst beo 54°C. Geringfugige Abweichungen von den Katalogerten sond moglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 008 TF.indd, js 90 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série Flange Mount / Standardgehäuse Monture à bride(s) / Montaje de brida Wheel Mount / Radnabengehäuse Monture à roue / Montaje de rueda Side Load - N (lbs) Side Load - N (lbs) 71,171 (16,000) 71,171 (16,000) Max Load Curve 62,275 (14,000) 53,378 (12,000) 53,378 (12,000) 44,482 (10,000) 44,482 (10,000) 35,584 (8,000) 35,584 (8,000) 26,688 (6,000) 26,688 (6,000) 17,792 (4,000) 17,792 (4,000) 8,896 (2,000) Max Load Curve 62,275 (14,000) 8,896 (2,000) Dynamic Load Curve Dynamic Load Curve 0 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Distance from Mounting Face - mm (in) Motor Image Not To Scale Distance from Mounting Face - mm (in) Motor Image Not To Scale The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. The dynamic side load curve is based on unidirectional steady state loads for L10 bearing life at 3 x 106 revolutions. Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 3 x 106 Umdrehungen kalkuliert. La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 3 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 3 x 106 revoluciones. Equation to Calculate the Expected Radial Bearing Life Gleichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 3 x 106 60 x S { FF } 3.33 a b Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min -1 L = Life In Hours / Lebensdauer in Stunden Fa = Dynamic side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281. 008 TF.indd, js 91 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série Code: AH SAE A 2-Bolt, ISO 6149-1 M22 x 1.5 "L" 64.3 (2.53) 15.7 (.62) 2.7 (.11) 106.4 (4.188) A A ø129.5 (5.10) Max ø 82.55 (3.250) 82.50 (3.248) B B 25.40 (1.000) ISO 6149-1 M22 X 1.5 O-RING PORTS Code AH disp. 0080 0100 63.068 (2.483) 0130 0140 0170 0195 0240 0280 0360 133.4 (5.25) ø13.48 (17/32) 0405 0475 Weight/Gewicht kg 13.6 13.6 13.8 13.9 14.2 14.5 14.9 15.2 16.0 16.5 17.2 Poids/Peso (lb) (29.9) (30.0) (30.5) (30.7) (31.3) (31.9) (32.9) (33.5) (35.2) (36.4) (37.9) 191 191 194 196 199 202 207 211 221 225 234 (7.51) (7.51) (7.63) (7.70) (7.82) (7.95) (8.13) (8.32) (8.70) (8.87) (9.20) Length "L" mm "L" (in) Code: AM O-Ring Ø12.37x2.62 SAE A 2-Bolt, Manifold Ø17.3 (0.68) Motor with manifold mount is supplied with 2 o-rings. 1.8 (0.091) Zum Motor mit Universalanschluß werden 2 o-ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Ø12.7 (0.5) Il blocchetto connessioni é corredato da 2 OR. "L" 64.3 (2.53) 15.7 (.62) 31.75 (1.250) ø129.5 (5.10) Max 2.7 (.11) 106.4 (4.188) A A ø 82.55 (3.250) 82.50 (3.248) B 63.50 (2.500) B B B-B 45.7 (1.8) B 14.29 (.563) 28.58 (1.125) 4 x 5/16-18 UNC thd x .500 min deep Code AM 133.4 (5.25) ø13.48 (17/32) 63.068 (2.483) disp. 0080 0100 0130 0140 0170 0195 0240 0280 0360 0405 0475 Weight/Gewicht kg 13.6 13.6 13.8 13.9 14.2 14.5 14.9 15.2 16.0 16.5 17.2 Poids/Peso (lb) (29.9) (30.0) (30.5) (30.7) (31.3) (31.9) (32.9) (33.5) (35.2) (36.4) (37.9) 191 191 194 196 199 202 207 211 221 225 234 (7.51) (7.51) (7.63) (7.70) (7.82) (7.95) (8.13) (8.32) (8.70) (8.87) (9.20) Length "L" mm "L" (in) English equivalents for metric specifications are shown in ( ). 008 TF.indd, js 92 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série Code: AS SAE A 2-Bolt, 7/8-14 SAE O-Ring "L" 64.3 (2.53) 15.7 (.62) 2.7 (.11) 106.4 (4.188) A A ø129.5 (5.10) Max ø 82.55 (3.250) 82.50 (3.248) B B 25.40 (1.000) 7/8-14 SAE O-Ring 63.068 (2.483) Code AS disp. 0080 0100 0130 0140 0170 0195 0240 0280 0360 133.4 (5.25) ø13.48 (17/32) 0405 0475 Weight/Gewicht kg 13.6 13.6 13.8 13.9 14.2 14.5 14.9 15.2 16.0 16.5 17.2 Poids/Peso (lb) (29.9) (30.0) (30.5) (30.7) (31.3) (31.9) (32.9) (33.5) (35.2) (36.4) (37.9) 191 191 194 196 199 202 207 211 221 225 234 (7.51) (7.51) (7.63) (7.70) (7.82) (7.95) (8.13) (8.32) (8.70) (8.87) (9.20) Length "L" mm "L" (in) Code: BS SAE B 2-Bolt, 7/8-14 SAE O-Ring "L" 65.3 (2.57) 57.7 (2.27) 15.7 (.62) A ø 129.5 (5.10) Max ø14.287 (9/16) 9.4 (.37) 174.5 (6.87) 146.0 (5.75) A ø 101.60 (4.00) 101.55 (3.998) B B 25.40 (1.000) 7/8-14 SAE O-Ring 62.8 (2.47) Code BS disp. 0080 0100 0130 0140 0170 0195 0240 0280 0360 0405 0475 Weight/Gewicht kg 14.2 14.2 14.5 14.6 14.8 15.1 15.5 15.8 16.6 17.1 17.8 Poids/Peso (lb) (31.3) (31.4) (31.9) (32.1) (32.7) (33.3) (34.3) (34.9) (36.6) (37.8) (39.3) 184 184 187 189 192 195 200 205 214 218 227 (7.25) (7.25) (7.37) (7.44) (7.56) (7.69) (7.87) (8.06) (8.44) (8.60) (8.94) Length "L" mm "L" (in) English equivalents for metric specifications are shown in ( ). 008 TF.indd, js 93 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série Code: LS Wheel, Front Brake Nose "L" 4.1 (.16) Min 64.7 (2.55) 36.8 (1.45) 19.1 (.75) 46.7 (1.84) 45˚ ø 76.2 (3.00) ø 126.90 / 127.00 (4.996/5.000) A A ø 88.85 (3.498) 88.80 (3.496) 135.0 (5.314) B B ø 126.6 (4.984) 25.40 (1.000) 147.6 (5.812) 13.49 (17/32) 4 x _5/16-18 UNC v.75 + _ .03 7/8-14 SAE O-Ring Code LS disp. 0080 0100 0130 0140 0170 0195 0240 0280 0360 0405 0475 Weight/Gewicht kg 14.0 14.0 14.2 14.3 14.6 14.9 15.3 15.6 16.3 17.0 17.5 Poids/Peso (lb) (30.9) (30.9) (31.2) (31.5) (32.1) (32.9) (33.7) (34.4) (35.9) (37.5) (38.6) Length "L" mm "L" (in) 146 146 149 151 154 157 162 167 175 180 189 (5.73) (5.73) (5.85) (5.92) (6.04) (6.17) (6.35) (6.54) (6.92) (7.08) (7.42) Code: MS Magneto, 7/8-14 SAE O-Ring 63.068 (2.483) "L" 64.3 (2.53) 15.7 (.62) 2.7 (.11) 22˚30´ A 22˚30´ A ø129.5 (5.10) Max ø 82.55 (3.250) 82.50 (3.248) B B 25.40 (1.000) ø106.4 (4.188) 7/8-14 SAE O-Ring Code MS 133.4 (5.25) ø13.48 (17/32) disp. 0080 0100 0130 0140 0170 0195 0240 0280 0360 0405 0475 Weight/Gewicht kg 13.6 13.6 13.8 13.9 14.2 14.5 14.9 15.2 16.0 16.5 17.2 Poids/Peso (lb) (29.9) (30.0) (30.5) (30.7) (31.3) (31.9) (32.9) (33.5) (35.2) (36.4) (37.9) 191 191 194 196 199 202 207 211 221 225 234 (7.51) (7.51) (7.63) (7.70) (7.82) (7.95) (8.13) (8.32) (8.70) (8.87) (9.20) Length "L" mm "L" (in) English equivalents for metric specifications are shown in ( ). 008 TF.indd, js 94 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série Code: US Wheel, Standard, 7/8-14 SAE O-Ring "L" 19.1 (.75) 36.8 (1.45) 63.8 (2.513) 46.7 (1.84) 45˚ 39.9 (1.57) 4.1 (.16) Min 6.6 (0.26) ø 82.55 (3.250) 82.50 (3.248) A A ø 62.99 (2.48) ø 126.90 / 127.00 (4.996 / 5.000) 135.0 (5.314) B B 25.40 (1.000) ø 147.6 (5.812) ø 13.48 (17/32) 7/8-14 SAE O-Ring Code US disp. 0080 0100 0130 0140 0170 0195 0240 0280 0360 0405 0475 Weight/Gewicht kg 13.9 13.9 14.2 14.3 14.5 14.8 15.2 15.5 16.3 16.9 17.5 Poids/Peso (lb) (30.6) (30.7) (31.2) (31.5) (32.0) (32.7) (33.6) (34.2) (35.9) (37.2) (38.6) Length "L" mm "L" (in) 146 146 149 151 154 157 162 167 176 180 189 (5.73) (5.73) (5.85) (5.92) (6.04) (6.17) (6.35) (6.54) (6.92) (7.08) (7.42) English equivalents for metric specifications are shown in ( ). 008 TF.indd, js 95 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série Code L Code A Code B Code M Code U Code: 01 1" 6B Spline 55.3 (2.18) 48.8 (1.92) 94.0 (3.70) 55.3 (2.18) 48.8 (1.92) 94.0 (3.70) Code: 02 1" Keyed Code: 03 1 1/4" Keyed 60.2 (2.37) 66.8 (2.63) 105.4 (4.15) English equivalents for metric specifications are shown in ( ). 008 TF.indd, js 96 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes Code: 01 1" 6B Spline Code: 02 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série 37.34 (1.47) 4.3 (.17) 1.24 (.049) 6.18 / 6.27 (.2435 / .2470) 25.4 (1.0) Min Full Spline 21.54 / 21.29 (.848 / .838) 25.32 / 25.02 (.997 / .985) 38.33 (1.509) 4.3 (.17) ø 25.65 (1.01) 6.38/6.35 (.251 / .250) 1" Keyed 27.66 / 28.30 (1.089 / 1.114) 25.40 / 25.37 (1.000 / .999) 24.37 / 25.40 (.922 / .930) 1.24 (.049) 19.0 (.748) 1/4 - 20 UNF Code: 03 50.3 (1.98) 7.912/7.887 (.3115/.3105) 36.5 (1.437) 1 1/4" Keyed 34.90 (1.374) 31.72 / 31.75 (1.249 / 1.250) _ 5/8-18 UNF 19.05 (.75) v English equivalents for metric specifications are shown in ( ). 008 TF.indd, js 97 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série Code L Code A Code B Code M Code U Code: 05 1 1/4" 14 Tooth Spline 64.0 (2.52) 57.4 (2.26) 102.6 (4.04) Code: 06 19 Tooth Spline 68.1 (2.68) 61.5 (2.42) 106.7 (4.20) 61.7 (2.43) 106.9 (4.21) Code: 07 15 Tooth Spline 68.3 (2.69) Code: 08 1 1/4" Tapered 68.3 (2.69) 61.7 (2.43) 106.9 (4.21) English equivalents for metric specifications are shown in ( ). 008 TF.indd, js 98 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Series / Serie / Série 47.2 (1.86) 29.06 (1.144) Min Full Spline 25.4 (1.0) 31.06 / 31.75 (1.223 / 1.250) _ Code: 05 5/8-18 UNF v 19.1 (.75) 3.18 / 3.32 (.1251 / .1309) ø 27.31 (1.075) 1 1/4" 14 Tooth Spline 28.42 (1.119) Min Full Spline 25.4 (1.00) 26.29 / 26.85 (1.035 / 1.057) 31.01 / 31.32 (1.221 / 1.233) Code: 06 19 Tooth Spline ø 27.94 / 28.45 (1.100 / 1.120) 2.31 / 2.49 (.0908 / .0982) 27.03 / 27.69 (1.064 / 1.090) 25.06 / 25.26 (.9865 / .9945) 39.37 (1.55) Min Full Spline 1/2-20 UNF thd _ v15.8 (.625) Code: 07 21.08 / 21.34 (.830 / .840) 15 Tooth Spline 2.31 / 2.49 (.0908 / .0982) 5/16x1 SAE J502 1:8 500 Nm (370 Ft Lb) Max See Installation Instructions ø31.88 (1.255) ø31.75 (1.249) Code: 08 1 1/4" Tapered 7.96 / 7.94 (0.313 / 0.312) 3.18 (.125) 35 (1.37) 1-20UNEF 19 (.748) English equivalents for metric specifications are shown in ( ). 008 TF.indd, js 99 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica (4.9 - 22.2 in3/rev) 81 . . . 364 cm3/rev 9 Displacements 9 Schluckvolumen 9 Cylindrée 9 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Cont. (to 3000 psi) . . . 207 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque MaxDrehmoment Couple Torque Maximo Int. (to 4000 psi) . . . 276 bar LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Clutch Series The Clutch Motor consists of a TF Series motor separated from the output shaft by a face spline coupling. The coupling is held apart by springs, disconnecting the motor from the output shaft, allowing the output shaft to freewheel. When hydraulic pressure is applied to either motor port, the springs separating the coupling are overcome and the motor is coupled to the output shaft. (to 25 gpm) . . .95 lpm (749 rpm) 749 rpm Cont. (4502 lb in) 509 Nm Int. (7029 lb in) 794 Nm Notes: 1) It is not recommended to engage the clutch while the output shaft is rotating. 2) Clutch may not disengage if there is residual torque on output shaft when pressure is lost at motor ports. 3) Minimum pressure to engage clutch - 200 PSI. 4) To assure clutch disengagement, pressure at motor ports must be below 60 PSI. 5) Shaft will freewheel when pressure is lost at motor ports whether by design or inadvertently. The possibility of unplanned freewheeling should be considered in the design of the system. 6) If applicable, contact factory for radial load capacity. 009 TF Clutch.indd, js 100 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TF XXXX Series LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Clutch Series GS Mounting/Ports Displacement Gehäuse/Anschluß Schluckvolumen Carter/Plan de raccordement Cylindrée Montaje/Lumbreras Desplazamiento Code 0080 0100 0130 0140 0170 0195 0240 0280 0365 cm3/tr cm3/giro cm3/U cu in3/rev 81 100 128 141 169 197 238 280 364 / / / / / / / / / 4.9 6.1 7.8 8.6 10.3 12.0 14.5 17.1 22.2 Code XX 0 XXXX Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion Options Opciones Mounting/Ports Magneto/7/8-14 SAE GS Code Shaft 1 1/4" Keyed 03 1 1/4" 14 Tooth Spline 05 Code 0 Rotation Standard Code AAAB AAAA Options No Paint No lackiert Black Paint Schwarz lackiert For other available options, see page 187. 009 TF Clutch.indd, js 101 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Clutch Series Code: GS 4 Bolt Magneto, Clutch / 7/8-14 SAE "L" 143.0 (5.63) 2.79 (.11) 63.068 (2.483) A Ø 82.55 (3.250) 82.50 (3.248) ø 129.5 (5.10) Max. B 22˚ 30' A 133.4 (5.25) B 106.38 (4.188) 25.40 (1.000) 4 x Ø 13.48 (17/32) 7/8-14 SAE O-Ring Code GS Weight/Gewicht Poids/Peso Length 45˚ disp. 0080 0100 0130 0140 0170 0195 0240 0280 0365 kg 17.9 17.9 18.1 18.2 18.5 18.8 19.2 19.5 20.3 (lb) (39.3) (39.4) (39.9) (40.1) (40.7) (41.3) (42.3) (42.9) (44.6) 270 270 273 275 278 281 286 290 300 (10.61) (10.61) (10.73) (10.80) (10.92) (11.05) (11.23) (11.42) (11.80) "L" mm "L" (in) For performance data curves, see TF section. English equivalents for metric specifications are shown in ( ). 009 TF Clutch.indd, js 102 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TF Clutch Series Code G Code: 03 1 1/4" Keyed 60.2 (2.37) Code: 05 1 1/4" 14 Tooth Spline Code: 03 63.5 (2.50) 50.3 (1.98) 36.5 (1.437) x 7.9 (.311) 8.01 / 7.91 (.3155 / .3115) 11.38 / 10.85 (.448 / .427) 1 1/4" Keyed 3.490 (1.374) 31.72 / 31.75 (1.249 / 1.250) _ 5/8 -18 UNF v19.1 (.75) Code: 05 47.2 (1.86) 31.72 / 31.75 (1.249 / 1.250) 44.5 (1.75) Min Full Spline 1 1/4"14 Tooth Spline _ 5/8-18 UNFv 25.4 (1.0) 3.18 / 3.32 (.1251 / .1309) 26.29 / 26.85 (1.035 / 1.057) English equivalents for metric specifications are shown in ( ). 009 TF Clutch.indd, js 103 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica (4.9 - 29.1 in3/rev) 81 . . . 477 cm3/rev 11 Displacements 11 Schluckvolumen 11 Cylindrée 11 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Cont. (to 3000 psi) . . . 207 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque MaxDrehmoment Couple Torque Maximo Int. (to 4000 psi) . . . 276 bar (to 25 gpm) . . . 95 lpm LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DF Series Brake Motor A Mechanical Brake Motor for Tough Applications Parker’s latest DF Series motor is truly another innovation the market has been waiting for. The compact size, reliable holding capability and ease of installation makes this new mechanical parking brake motor the perfect choice for many turf or agricultural applications using hydraulics for wheel motors. This mechanically applied version of the brake motor is available in 11 motor displacements 80 cm3/rev (4.9 in3/rev) to 475 cm3/rev (29.1 in3/rev). Pressure capacities are up to 280 bar (4,000 psi) intermittent and 210 bar (3,000 psi) continuous. Flows up to 95 lpm (25 gpm) and speed up to 749 rpm are available. Motor output torque up to 916 Nm (8,106 lb in) intermittent and 681 Nm (6,027 lb in) continuous is available. (749 rpm) 749 rpm Cont. (6027 lb in) 681 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral Int. (8106 lb in) 916 Nm (to 3597 lb) . . . 16000 N Holding capacity is 497 Nm (4,400 in lbs) with 68 Nm (600 in lbs) of input torque at lever pivot. Brake capacities are typical for non-burnished brake shoe. OEM testing required to verify actual field conditions. Das maximale Bremsmoment von 497 Nm (4400 in Ibs) wird erreicht durch Betätigung des Bremshebels mit 68 Nm ( 600 in Ibs). Genannte Einsatzdaten beziehen sich auf Neuprodukte. Die Eignung der Geräte ist vom Anwender für den jeweiligen Einsatz individuell zu prüfen . La puissance de maintien est de 497 Nm (4400 pouces-livres) avec couple d’entrée au pivot du levier de 68 Nm (600 pouces-livres). Les puissances de freinage sont typiques pour des sabots de frein non brunis. Les essais imposés par le constructeur d’origine exigent la vérification des conditions réelles sur place. Capacidad de retención de 497 N-m (4.400 libras-pulgada) con 69 N-m (600 libras-pulgada) de torque de entrada en el brazo de articulación. Los valores de capacidad de frenado son típicas para zapatas de freno no bruñidas. Para fabricantes de equipos originales se deben efectuar pruebas bajo condiciones reales de funcionamiento. 010 DF.indd, js 104 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DF Series Brake Motor .. Wheel Mount/Radnabengehause Monture à roue/ Montaje de rueda Side Load - N (lbs) 71,171 (16,000) Max Load Curve 62,275 (14,000) 53,378 (12,000) 44,482 (10,000) 35,584 (8,000) 26,688 (6,000) 17,792 (4,000) Dynamic Load Curve 8,896 (2,000) 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Distance from Mounting Face - mm (in) Motor Image Not To Scale The dynamic side load curve is based on uni-directional steady state loads for L10 bearing life at 3 x 106 revolutions. Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 3 x 106 Umdrehungen kalkuliert. La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 3 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 3 x 106 revoluciones. The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. Equation to Calculate the Expected Radial Bearing Life Gelichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 3 x 106 60 x S Fa Fb { } 3.33 Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min-1 L = Life In Hours / Lebensdauer in Stunden Fa = Dynamic side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281 010 DF.indd, js 105 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos DF Series Code XXXX LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DF Series Brake Motor XS 8 X 0 XXXX Rotation Shaft Options Drehrichtung Welle Opciones Arbre Direction de rotation Rotacion Eje Drum Type Displacement Mounting/Ports Trommelbremse Schluckvolumen Gehäuse/Anschluß Cylindrée Carter/Plan de raccordement Tipo de tambor Genre de tambour Desplazamiento Montaje/Lumbreras cm3/U cm3/tr cm3/giro cu in3/rev 0080 0100 0130 0140 0170 0195 81 100 128 141 169 197 / / / / / / 4.9 6.1 7.8 8.6 10.3 11.9 0240 0280 0360 0405 0475 238 280 364 405 477 / / / / / 14.5 17.1 22.2 24.7 29.1 Code Front Port Rotation 0 Standard Code AAAB Code Mounting/Ports AAAA AS Wheel Mt. w/Brake Lever @ 105o/ BS CS DS ES FS GS HS Wheel Mt. w/Brake Lever @ 165o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 195o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 255o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 285o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 345o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 15o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 75o / 7/8-14 SAE Description No Paint No lackiert Black Paint Schwarz lackiert 7/8-14 SAE Code Drum Type A 4 Bolt B 5 Bolt Code Shaft Avail. 1 1/4” Tapered 8 For other available options, see page 187. 010 DF.indd, js 106 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DF Series Brake Motor Code: AS Wheel Mount w/Brake Lever / 7/8-14 SAE O-Ring 106.9 (4.21) "L” 36.8 (1.45) 19.1 (.75) Torque Nut to 169 Nm (125 Ft Lbs) Min Plus Rotation to Align Cotter Pin Ø 6.70 (.264) 19.2 (.757) 4.1 (.16) Min 5˚ 50.8 (2.0) 10 60.0 88.85 (3.498) (2.362) 88.80 (3.496) A 127.00 (5.000) Ø 126.90 (4.996) B A B 1/2-20 UNF 13.5 (0.53) Ø 46.7 (1.84) 95.1 (3.743) 63.83 (2.513) Ø147.62 (5.812) 22.0 (.866) 46.0 (1.811) Note: 1. Brake Acuation Lever can be positioned in 12.00° increments from that shown. Bremshebel ist kreisförmig in Sigmenten von 12.00 ° positionierbar. Le levier de commande du frein peut être positionné à des échelons d’accroissement de 12,00° de ce qui est montré. El brazo de actuación del freno se puede colocar en avances de 12,00 grados con respecto a la posición mostrada. 2. Brake Acuation Lever is shipped unattached, secured with wire or tiewrap to assembly. Hebel ist anbei. Endmontage erforderlich. Le levier de commande du frein est expédié sous forme détachée; il est attaché à l’ensemble avec du fil ou du ruban. El brazo de actuación del freno se suministra suelto, sin conexión, sólo atado provisoriamente al mecanismo. Code AS disp. 0080 0100 0130 0140 0170 0195 0240 0280 0360 0405 0475 Weight/Gewicht kg 18.0 18.1 18.3 18.4 18.7 19.0 19.4 19.7 20.4 21.0 21.7 Poids/Peso (lb) (39.74) (39.84) (40.34) (40.64) (41.14) (41.84) (42.74) (43.34) (45.04) (46.34) (47.74) Length "L" mm "L" (in) 146 146 149 151 154 157 162 167 176 180 189 (5.73) (5.73) (5.85) (5.92) (6.04) (6.17) (6.35) (6.54) (6.92) (7.08) (7.42) For performance data curves, see TF section. English equivalents for metric specifications are shown in ( ). 010 DF.indd, js 107 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Dimensional Data/Abmessungen Metrage/Datos de dimensiones LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DF Series Brake Motor Drum Type/Trommelbremse/ Tipo de tambor/ Genre de Tambour Code: A Code: B 4 X ½-20 UNF 4 Bolt 5 X ½-20 UNF Ø114.3 (Ø4.500) 5 Bolt 1/8 X 50.8 (2.00) COTTER PIN Ø165.48 (Ø6.515) 1/8 X 50.8 (2.00) COTTER PIN Ø101.6 (Ø4.000) Ø165.48 (Ø6.515) Shafts / Abtriebswellen Arbre / Ejes Code: 8 1 1/4" Taper 106.9 (4.21) 5/16x1 SAE J502 8.01 (.3155) 7.91 (.3115) 1:8 ø31.88 (1.255) ø31.75 (1.249) 35 (1.37) 7.62 (.300) 7.21 (.284) 1-20 UNEF 19 (.748) English equivalents for metric specifications are shown in ( ). 010 DF.indd, js 108 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Notes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DF Series Brake Motor 010 DF.indd, js 109 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica (8.6 to 22.2 in3/rev) 140 . . . 364 cm3/rev 7 Displacements 7 Schluckvolumen 7 Cylindrée 7 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Cont. (to 2750 psi) . . . 190 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque MaxDrehmoment Couple Torque Maximo 011 TL.indd, js Int. (to 3500 psi) . . . 241 bar LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série Exceptional Power Density and Durability The heart of the new compact TorqmotorTM is the strongest drive train in its class. Coupled with this extra heavy-duty drive train are the high efficiencies and low speed performance for which the Parker TorqmotorTM is known. As with all TorqmotorsTM, high speed valving and full flow drive train lubrication are standard. Case drains are not required. Roller vanes and a sealed commutator maintain high efficiencies and provide smooth low speed performance. (to 25 gpm) . . . 95 lpm (484 rpm) 484 rpm Cont. (8,650 lb in) 977 Nm Int. (10,300 lb in) 1164 Nm G2TorqTL.cdr ANR2455 110 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l Cil ndré luck acem ind e vo lum ent Ma rata en x. Ma spe ed x. Vit Dre @ M e h Ve sse d zahl ax. i loc e r Inte nte rm ida ot d m atio rmitt itte Ma ax n m iere nt fl x. im nd o Ma oil a a axi er w flo x Be ca Dé . Sch w t rie ud b lu al b: Po it d´h cks int t r ta e r u rm ta ile m om it e ma nte Ma x axi ma x. x im Ma diff e re o x. Ch Dru nti ute ck al p g r Pr es de p efäll essu ion re e re s dif sio e n r en Ma m c ia a x i x lm Ma . sup ax x p im Pr . Ein ly pr a es ga es s n s Pr ion gs ur es e d ion max ruc ma i en k x im t ré Ma x ad e Ma . torq ea x. lim u Co Dre e en tac up hm ion To le m om rqu e a n t e M xi ax Ma im x o Ma . per for x. L m Pu is eist anc Po sanc unga e ten e b za de gab me sor e Mi c c t ie n. an ica max Mi star n. ma i t i n x Co Anla g to up r u To le m fmo que rqu m e m in. fo ent ini urn mo i a de u dé a rr m an anr qu e age LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série max bar psi cont / int Nm lb-in 190 241 2750 3500 300 4350 364 463 3226 4095 30 40 294 365 2606 3234 95 25 190 241 2750 3500 300 4350 449 570 3970 5042 31 41 354 445 3137 3943 68 18 95 25 190 241 2750 3500 300 4350 511 648 4520 5739 34 46 414 526 3666 4654 399 68 18 95 25 190 241 2750 3500 300 4350 620 790 5485 6990 34 46 536 679 4740 6011 280 17.1 335 68 18 95 25 190 241 2750 3500 300 4350 730 929 6460 8218 34 45 619 787 5479 6967 TL 0310 310 18.9 310 68 18 95 25 190 241 2750 3500 300 4350 847 1079 7499 9548 36 48 713 907 6309 8029 TL 0360 364 22.2 255 68 18 95 25 172 224 2500 3250 300 4350 890 1163 7874 10293 31 42 778 1002 6882 8867 cont / int l/min g/min Motor Series TL cm3/rev in3/rev rev/min TL0140 140 8.6 613 68 18 95 25 TL0170 169 10.3 512 68 18 TL 0195 195 11.9 484 TL 0240 238 14.5 TL 0280 cont / int bar psi Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. max KW HP cont / int Nm lb-in Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Peak operation rating applies to 1% max of every minute. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 011 TL.indd, js 111 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TL Series Code 0140 0170 0195 0240 0280 0310 0360 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série XXXX XX XX 0 XXXX Displacement Schluckvolumen Cylindrée Desplazamiento Mounting/Ports Gehäuse/Anschluß Carter/Plan de raccordement Montaje/Lumbreras Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion Options Opciones cm3/tr cm3/giro cm3/U cu in3/rev 141 169 195 238 280 310 364 / / / / / / / 8.6 10.3 11.9 14.5 17.1 18.9 22.2 Code Mounting/Ports Wheel, Front Brake Nose, 7/8-14 SAE Code Front Port Rotation LS 0 Standard Wheel,Standard, 7/8-14 SAE US Code AAAB AAAA Code No Paint No lackiert Black Paint Schwarz lackiert Shaft 1 1/4" Tapered 08 For other available options, see page 187. 011 TL.indd, js 112 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série TL 0140 2 5 10 500 20 Flow [G/min] Schluckstrom [L/min] 40 50 60 70 75 80 30 90 95 4,500 .5 1 2 3 4 5 7 9 12 15 US 25 18 4,000 400 3,500 240 3500 170 200 2,500 3000 2750 2,000 psi 190 bar 210 Torque [lb/in] Drehmoment [Nm] 3,000 300 2500 1,500 140 2000 1,000 100 1500 100 500 1000 500 70 35 0 0 50 100 150 200 250 300 350 400 Drehzahl [1/min] 450 0 500 550 600 0 650 50 100 150 200 250 300 350 400 450 500 550 600 650 Speed [Rpm] TL 0170 2 5 10 600 20 Schluckstrom [L/min] 40 50 60 70 75 80 30 .5 1 2 3 4 5 90 95 550 9 Flow [G/min] 12 15 18 US 25 5,000 500 4,500 240 3500 4,000 210 350 3,500 300 170 250 bar 190 Torque [lb/in] 400 2750 2,500 2500 2,000 140 200 3000 3,000 psi 450 Drehmoment [Nm] 7 5,500 2000 1,500 150 100 70 50 500 35 0 0 50 100 150 200 250 300 Drehzahl [1/min] 350 400 1500 1,000 100 1000 500 0 450 500 0 550 50 100 150 200 250 300 350 400 450 500 550 Speed [Rpm] TL 0195 Schluckstrom [L/min] 700 2 5 10 20 30 40 50 60 70 75 80 .5 1 2 3 4 5 6,000 90 95 7 9 12 Flow [G/min] 15 US 18 25 650 600 5,000 550 210 350 190 300 170 250 Torque [lb/in] 400 150 3000 3,000 2750 2500 2,000 140 200 3500 4,000 2000 100 1500 1,000 100 50 70 0 35 500 0 50 100 150 200 250 300 350 400 450 1000 500 0 0 Drehzahl [1/min] Cont. psi 240 450 bar Drehmoment [Nm] 500 50 100 150 200 250 300 Speed [Rpm] 350 400 450 500 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 011 TL.indd, js 113 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série TL 0240 2 5 10 20 30 40 50 60 70 75 80 90 95 8,000 .5 1 2 3 4 5 7 9 Flow [G/min] 12 15 US 18 25 7,000 6,000 210 190 170 140 5,000 3500 4,000 3000 2750 2500 3,000 2000 2,000 100 1500 70 1,000 35 0 25 50 1000 500 0 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 Drehzahl [1/min] 0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 Speed [Rpm] TL 0280 2 5 10 20 Schluckstrom [L/min] 40 50 60 70 75 80 30 .5 1 2 3 4 5 9,000 900 7 9 12 15 18 25 8,000 240 800 700 7,000 3500 6,000 3000 2750 210 Torque [lb/in] 190 600 170 bar Drehmoment [Nm] US Flow [G/min] 90 95 500 140 400 5,000 2500 4,000 2000 3,000 300 1500 100 2,000 200 70 100 0 0 25 50 75 100 125 150 175 200 Drehzahl [1/min] 225 250 275 300 325 1000 1,000 35 350 500 0 0 25 50 75 100 .5 1 2 3 4 5 10,000 7 9 125 150 175 200 Speed [Rpm] 225 250 275 300 325 350 TL 0310 2 5 10 20 Schluckstrom [L/min] 40 50 60 70 75 80 30 90 95 1,000 US Flow [G/min] 15 18 25 9,000 900 8,000 800 240 700 210 3500 Torque [lb/in] 7,000 190 600 170 500 bar Drehmoment [Nm] 12 140 3000 2750 6,000 2500 psi 1,100 psi 1,000 psi Torque [lb/in] 240 bar Drehmoment [Nm] Schluckstrom [L/min] 850 800 750 700 650 600 550 500 450 400 350 300 250 200 150 100 50 0 5,000 2000 4,000 400 3,000 300 1500 100 2,000 200 70 1000 1,000 100 35 0 0 25 Cont. 50 75 100 125 150 175 Drehzahl [1/min] 200 225 250 275 300 500 0 0 325 25 50 75 100 125 150 175 Speed [Rpm] 200 225 250 275 300 325 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 011 TL.indd, js 114 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série TL 0360 2 5 10 20 30 Schluckstrom [L/min] 40 50 60 70 75 80 90 95 12,000 1,100 4 5 7 9 12 Flow [G/min] 15 18 US 25 11,000 225 210 1,000 900 10,000 190 800 600 140 500 400 Torque [lb/in] 170 700 bar Drehmoment [Nm] .5 1 2 3 9,000 3250 8,000 3000 2750 7,000 2500 psi 1,200 6,000 2000 5,000 4,000 100 1500 300 3,000 70 200 2,000 100 1000 1,000 35 0 0 25 Cont. 50 75 100 125 150 Drehzahl [1/min] 175 200 225 250 500 0 0 275 25 50 75 100 125 150 Speed [Rpm] 175 200 225 250 275 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 011 TL.indd, js 115 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série Wheel Mount / Radnabengehäuse Monture à roue/ Montaje de rueda Side Load - N (lbs) 71,171 (16,000) 62,275 (14,000) 53,378 (12,000) 44,482 (10,000) 35,584 (8,000) 26,688 (6,000) 17,792 (4,000) 8,896 (2,000) Dynamic Load Curve 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Distance from Mounting Face - mm (in) Motor Image Not To Scale The dynamic side load curve is based on unidirectional steady state loads for L10 bearing life at 3 x 106 revolutions. Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 3 x 106 Umdrehungen kalkuliert. La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 3 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 3 x 106 revoluciones. The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. Equation to Calculate the Expected Radial Bearing Life Gleichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 3 x 106 60 x S { FF } 3.33 a b Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min -1 L = Life In Hours / Lebensdauer in Stunden Fa = Dynamic side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung 011 TL.indd, js 116 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting / Gehäuse Carter / Montaje Code: L LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série US Wheel, Front Brake Nose "L" 4.1 (.16) Min 63.8 (2.513) 36.8 (1.45) 19.1 (.75) 46.7 (1.84) 45˚ ø 76.2 (3.00) A A ø 127.00 / 126.9 (5.000 / 4.996) ø 88.80 (3.496) 88.85 (3.498) 135.0 (5.314) B B o/ 147.6 (5.812) o/ 4 x 13.49 (17/32) Code L disp. 0140 0170 0195 0240 0280 0310 0360 Weight/Gewicht kg 10.9 11.1 11.4 11.8 12.2 12.4 12.9 Poids/Peso (lb) (24.1) (24.6) (25.2) (26.0) (26.9) (27.4) (28.4) Length "L" mm "L" (in) Code: U 4 x 5/16-18 UNC 114 114 114 117 119 122 133 (4.47) (4.47) (4.47) (4.61) (4.80) (4.94) (5.22) US Wheel, Standard "L" 19.1 (.75) 36.8 (1.45) 63.8 (2.513) 46.7 (1.84) 45˚ 39.9 (1.57) 4.1 (.16) Min 6.6 (0.26) ø 82.55 (3.250) 82.50 (3.248) A A ø 62.99 (2.48) ø 127.00 / 126.90 (5.000 / 4.996) 135 (5.314) B B 147.6 (5.812) 4 x ø 13.48 (17/32) Code L disp. 0140 0170 0195 0240 0280 0310 0360 Weight/Gewicht kg 10.9 11.1 11.4 11.8 12.2 12.4 12.9 Poids/Peso (lb) (24.1) (24.6) (25.2) (26.0) (26.9) (27.4) (28.4) Length "L" mm "L" (in) 114 114 114 117 119 122 133 (4.47) (4.47) (4.47) (4.61) (4.80) (4.94) (5.22) English equivalents for metric specifications are shown in ( ). 011 TL.indd, js 117 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ports / Anschlüße Orifices / Lumbreras Code: S LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série US 7/8-14 SAE O-Ring 25.40 (1.000) 7/8-14 SAE O-Ring English equivalents for metric specifications are shown in ( ). 011 TL.indd, js 118 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TL Series / Serie / Série Code L & U Code: 08 US 1 1/4" Tapered 106.9 (4.21) 5/16x1 SAE J502 1:8 Code: 08 500 Nm (375 Ft Lb) ø31.88 (1.255) ø31.75 (1.249) US 7.96 / 7.94 (0.313 / 0.312) 3.18 (.125) 1 1/4" Tapered 35 (1.37) 1-20UNEF 19 (.748) English equivalents for metric specifications are shown in ( ). 011 TL.indd, js 119 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica (8.6 to 58.5 in3/rev) 141 . . . 959 cm3/rev 13 Displacements 13 Schluckvolumen 13 Cylindrée 13 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Cont. (to 3000 psi) . . . 207 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque MaxDrehmoment Couple Torque Maximo Int. (to 4000 psi) . . . 276 bar LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série Exceptional Strength and Durability in a High Performance Motor The heart of Parker’s TG Series powertrain, the torque link, is an extra heavy duty part that includes patented 60:40 spline geometry. Rugged construction throughout allows the transmission of over 13,000 lb-in of torque. The entire powertrain is continually washed in cool, high flow fluid to assure long life. Roller vanes and sealed commutator maintain high efficiency and provide smooth low speed performance. (to 30 gpm) . . . 114 lpm (660 rpm) 660 rpm Cont. (9,239 lb in) 1044 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral Int. (12,636 lb in) 1428 Nm (to 3597 lb) . . . 16000 N 012 TG.indd, js 120 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l Cil ndré luck acem ind e vo lum ent Ma rata en x. Ma spe ed x. Vit Dre @ M e h Ve sse d zahl ax. i loc e r Inte nte rm ida ot d m atio rmitt itte Ma ax n m iere nt fl x. im nd o Ma oil a a axi er w flo x Be ca Dé . Sch w t rie ud b lu al b: Po it d´h cks int t r ta e r u rm ta ile m om it e ma Ma nte x axi x. ma d Ma iff x im er x o Ch . Dru enti a u c l Pr te de kgef pres es ä ion pre lle sure dif ssio Ma e re n m x nc Ma . sup ia l a x i x. ply ma E Pr p i n x im r es ga e a Pr sion ngs ssur es e ion max druc ma i en k Ma x im t ré x ad e Ma . torq ea x. u e lim Co Dre en up hm tac To le m om ion rqu e a nt e M xi ax Ma im x o Ma . per for x. L m Pu is eist anc Po sanc unga e ten e b za de gab me sor e Mi n. c c t ie an Mi star ica max n. t i ma i Co Anla ng to x up ufm rqu l To e m o rqu me e i n e m . fo nt ini urn mo i a de u dé a rr m an anr qu e age LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série max bar psi cont / int* Nm lb-in 276 4000 300 4350 390 3455 530 4692 33 45 315 2791 418 3706 207 3000 276 4000 300 4350 476 4216 646 5714 33 45 376 3331 505 4469 95 25 207 3000 276 4000 300 4350 556 4919 753 6663 33 45 451 3989 611 5408 76 20 95 25 207 3000 276 4000 300 4350 677 5991 913 8081 32 44 582 5152 776 6865 334 76 20 95 25 207 3000 276 4000 300 4350 796 7044 1073 9499 31 42 675 5972 870 7699 310 18.9 303 76 20 95 25 207 3000 276 4000 300 4350 924 8184 1229 10817 31 41 778 6882 1005 8893 TG 0335 337 20.6 277 76 20 95 25 207 3000 276 4000 300 4350 964 8533 1297 11479 30 41 843 7458 1117 9889 TG 0405 405 24.7 232 76 20 95 25 172 2500 241 3500 300 4350 942 8336 1342 11877 27 37 791 7002 1145 10133 TG 0475 477 29.1 237 76 20 114 30 138 2000 207 3000 300 4350 887 7853 1372 12145 28 38 740 6549 1120 9909 TG 0530 528 32.3 213 76 20 114 30 138 2000 172 2500 300 4350 983 8701 1253 11086 23 31 874 7737 1091 9657 TG 0625 623 38.0 182 76 20 114 30 121 1750 155 2250 300 4350 986 8727 1291 11424 20 27 895 7924 1165 10312 TG 0785 786 48.0 143 76 20 114 30 103 1500 138 2000 300 4350 1044 9239 1428 12636 17 23 991 8772 1341 11876 TG 0960 959 58.5 118 76 20 114 30 69 1000 103 1500 300 4350 773 6843 1268 11227 12 16 763 6752 1177 10419 cont / int* l/min g/min cont / int* bar psi Motor Series TG cm3/rev in3/rev rev/min TG 0140 141 8.6 660 76 20 95 25 207 3000 TG 0170 169 10.3 554 76 20 95 25 TG 0195 195 11.9 477 76 20 TG 0240 238 14.5 393 TG 0280 280 17.1 TG 0310 Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. * Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. max KW HP cont / int* Nm lb-in Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 012 TG.indd, js 121 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TG Series Code 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série XXXX XX XX 0 XXXX Displacement Schluckvolumen Cylindrée Desplazamiento Mounting/Ports Gehäuse/Anschluß Carter/Plan de raccordement Montaje/Lumbreras Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion Options Opciones cm3/tr cm3/giro cm3/U cu in3/rev 141 169 195 238 280 310 337 405 477 528 623 786 959 / / / / / / / / / / / / / 8.6 10.3 11.9 14.5 17.1 18.9 20.6 24.7 29.1 32.3 38.0 48.0 58.5 Code Mounting/Ports SAE "A" 2 Bolt, 5/16-18 UNC Manifold Code Front Port Rotation AM 0 Standard SAE "A" 2 Bolt, 7/8-14 SAE AS Code AAAB Wheel, Front Brake Nose, 7/8-14 SAE No Paint No lackiert Black Paint Schwarz lackiert AAAA LS Magneto, 7/8-14 SAE MS Code Shaft 1" 6B Spline Wheel,Standard, 01* 7/8-14 SAE 1 1/4" Keyed 03 US Wheel, Optional, Manifold Rear Port 1 1/4" 14 Tooth Spline 05 A WE* 19 Tooth Spline B * Requires rear porting. Nur Endanschluss moglich Exige des orifices en arriere Necesita lumbrera posterior 06 1 1/4" Tapered** 08 1 3/8" J501 Taper 19 * Abtriebswelle } Ø 25mm Max. Moment cont./int. Coupling shaft Ø 1 inch Max. torque cont./int. Arbre 6B SAE Couple maxi cont./int. Eje de acople Coppia max cont./int. 450/550 Nm For other available options, see pages 182-187. 012 TG.indd, js 122 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série TG 0140 Flow [G/min] 15 Schluckstrom [L/min] 600 20 2 10 40 30 60 50 70 76 80 .5 3 90 95 7 5 12 9 20 US 25 5000 4500 500 280 4000 4000 3500 3500 210 3000 140 200 3000 2500 2500 2000 2000 psi 170 Torque [lb/in] 300 240 bar Drehmoment [Nm] 400 1500 1500 100 1000 100 1000 70 500 35 0 0 100 200 300 400 500 600 500 0 0 700 100 200 300 400 500 600 700 Speed [Rpm] Drehzahl [1/min] TG 0170 Schluckstrom [L/min] 700 2 20 10 30 40 50 70 76 80 60 .5 2 3 6000 90 95 5 9 7 12 Flow [G/min] 15 20 US 25 500 240 4000 4500 3500 4000 Torque [lb/in] 210 400 170 300 5000 140 200 3000 3500 3000 2500 psi 280 bar Drehmoment [Nm] 5500 600 2500 2000 2000 1500 100 100 70 0 100 200 300 400 500 1000 500 500 0 35 600 0 1500 1000 0 50 100 150 200 250 300 350 400 450 500 550 600 Speed [Rpm] Drehzahl [1/min] TG 0195 Schluckstrom [L/min] 210 20 30 40 50 60 .5 3 7000 90 95 70 76 80 800 5 9 7 12 Flow [G/min] 15 US 20 25 6500 700 4000 6000 280 500 210 400 170 4500 140 300 3500 5000 3000 4000 2500 3500 psi 240 Torque [lb/in] 600 bar Drehmoment [Nm] 5500 3000 2000 2500 2000 200 100 100 70 1000 1000 500 35 50 Cont. 100 150 200 250 300 Drehzahl [1/min] 350 400 450 500 0 0 0 1500 1500 0 500 50 100 150 200 250 300 350 400 450 500 Speed [Rpm] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 012 TG.indd, js 123 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série TG 0240 Schluckstrom [L/min] 20 2 10 40 30 60 50 70 76 80 90 95 9000 1000 .5 3 7 5 12 9 Flow [G/min] 15 US 20 25 8000 900 280 4000 7000 600 210 500 170 400 140 3500 6000 3000 5000 2500 psi 240 Torque [lb/in] 700 bar Drehmoment [Nm] 800 4000 2000 3000 300 100 2000 70 1000 35 0 1500 200 1000 100 500 0 0 50 100 150 200 250 300 Schluckstrom [L/min] 60 50 70 76 80 90 95 350 0 400 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 Speed [Rpm] Drehzahl [1/min] TG 0280 2 10 20 30 40 Flow [G/min] 0.5 3 10000 1200 1100 12 9 15 20 US 25 9000 1000 4000 280 8000 900 210 6000 3000 5000 2500 4000 2000 170 500 140 400 3000 300 psi 600 7000 Torque [lb/in] 700 3500 240 bar 800 Drehmoment [Nm] 7 5 1500 100 2000 200 70 100 1000 1000 35 0 0 50 100 150 200 250 300 500 0 350 0 50 100 150 200 Speed [Rpm] Drehzahl [1/min] 250 300 350 TG 0310 Schluckstrom [L/min] 2 5 10 1400 20 30 50 40 60 70 76 80 90 95 0.5 12 3 4 5 13000 7 9 12 Flow [G/min] 15 US 20 25 12000 1200 11000 10000 9000 210 8000 170 600 140 Torque [lb/in] 800 240 400 4000 3500 3000 7000 psi 1000 bar Drehmoment [Nm] 280 2500 6000 5000 2000 4000 100 70 200 35 Cont. 50 100 150 Drehzahl [1/min] 200 250 1500 2000 1000 1000 0 0 3000 500 0 300 0 Int. 50 100 150 Speed [Rpm] 200 250 300 Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 012 TG.indd, js 124 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série TG 0335 2 10 20 30 40 50 Schluckstrom [L/min] 70 76 80 60 .5 3 90 95 5 9 7 US Flow [G/min] 15 20 12 25 13000 1400 12000 11000 280 1000 240 9000 210 8000 4000 170 600 Torque [lb/in] 800 bar Drehmoment [Nm] 10000 140 3500 3000 7000 6000 2500 5000 2000 psi 1200 4000 400 100 200 70 1500 3000 2000 1000 1000 35 0 50 100 150 200 250 500 0 0 0 300 50 100 150 200 250 300 Speed [Rpm] Drehzahl [1/min] TG 0405 US Flow [G/min] Schluckstrom [L/min] 2 10 20 30 40 50 60 70 76 80 90 95 13000 1400 .5 3 7 5 12 9 15 20 25 12000 240 1200 1000 3500 10000 3000 9000 8000 140 600 100 2500 7000 psi 800 Torque [lb/in] 170 bar Drehmoment [Nm] 11000 210 2000 6000 5000 1500 4000 400 70 200 35 3000 1000 2000 1000 500 0 0 0 50 100 150 Drehzahl [1/min] 200 0 250 50 100 Speed [Rpm] 150 200 250 TG 0475 2 10 20 30 Schluckstrom [L/min] 50 60 70 76 80 40 90 100 .5 3 13000 114 1600 5 7 9 12 US Flow [G/min] 15 20 25 30 12000 1400 11000 10000 1200 210 Torque [lb/in] 8000 800 140 bar 170 600 2000 6000 5000 1500 4000 100 400 2500 7000 psi 1000 Drehmoment [Nm] 3000 9000 3000 1000 2000 70 200 1000 35 0 0 25 Cont. 50 75 100 125 150 Drehzahl [1/min] 175 200 225 500 0 0 250 25 50 75 100 125 Speed [Rpm] 150 175 200 225 250 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 012 TG.indd, js 125 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série TG 0530 2 10 20 30 Schluckstrom [L/min] 50 60 70 76 80 40 90 100 114 .5 13000 1400 3 5 7 9 US Flow [G/min] 15 20 12 25 30 12000 1200 11000 10000 170 9000 2500 140 600 100 7000 2000 6000 5000 psi Torque [lb/in] 8000 800 bar Drehmoment [Nm] 1000 1500 4000 400 3000 70 1000 2000 200 1000 0 0 20 40 60 80 100 120 Drehzahl [1/min] 140 160 180 200 35 220 500 0 0 25 50 75 100 125 Speed [Rpm] 150 Flow [G/min] 20 25 175 200 225 TG 0625 1400 2 10 20 US 30 40 Schluckstrom [L/min] 60 70 76 80 90 50 100 114 13000 .5 3 5 7 9 12 15 30 12000 11000 1200 10000 1000 9000 150 2250 120 600 bar 800 100 7000 1750 6000 psi Torque [lb/in] Drehmoment [Nm] 8000 1500 5000 4000 400 3000 70 1000 2000 200 1000 0 0 25 50 75 100 125 Drehzahl [1/min] 150 175 0 35 200 0 20 40 60 80 100 120 140 160 180 Speed [Rpm] TG 0785 1600 2 10 20 30 40 50 Schluckstrom [L/min] 60 70 76 80 90 100 500 200 114 14000 .5 3 5 7 9 12 15 Flow [G/min] 20 US 25 30 13000 1400 12000 11000 1200 140 10000 600 400 8000 7000 psi 100 Torque [lb/in] 800 bar Drehmoment [Nm] 2000 9000 1000 1500 6000 5000 4000 70 1000 3000 2000 200 1000 0 0 Cont. 25 50 75 Drehzahl [1/min] 100 125 35 150 0 0 25 50 75 Speed [Rpm] 100 125 500 150 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 012 TG.indd, js 126 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série TG 0960 2 10 20 30 40 Schluckstrom [L/min] 50 60 70 76 80 90 100 114 13000 1400 .5 3 5 7 9 12 Flow [G/min] 15 20 US 25 30 12000 1200 11000 10000 9000 100 70 7000 psi Torque [lb/in] 600 1500 8000 800 bar Drehmoment [Nm] 1000 6000 5000 1000 4000 400 3000 2000 200 1000 0 0 Cont. 20 40 60 Drehzahl [1/min] 80 100 35 120 0 0 25 50 Speed [Rpm] 75 100 500 125 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 012 TG.indd, js 127 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série Flange Mount / Standardgehäuse Monture à bride(s) / Montaje de brida Wheel Mount / Radnabengehäuse Monture à roue/ Montaje de rueda Side Load - N (lbs) Side Load - N (lbs) 71,171 (16,000) 71,171 (16,000) Max Load Curve 62,275 (14,000) 53,378 (12,000) 53,378 (12,000) 44,482 (10,000) 44,482 (10,000) 35,584 (8,000) 35,584 (8,000) 26,688 (6,000) 26,688 (6,000) 17,792 (4,000) 17,792 (4,000) 8,896 (2,000) Max Load Curve 62,275 (14,000) Dynamic Load Curve 8,896 (2,000) Dynamic Load Curve 0 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Distance from Mounting Face - mm (in) Motor Image Not To Scale Distance from Mounting Face - mm (in) Motor Image Not To Scale The dynamic side load curve is based on uni-directional steady state loads for L10 bearing life at 3 x 106 revolutions. Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 3 x 106 Umdrehungen kalkuliert. La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 3 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 3 x 106 revoluciones. The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. Equation to Calculate the Expected Radial Bearing Life Gleichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 3 x 106 60 x S { FF } 3.33 a b Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min -1 L = Life In Hours / Lebensdauer in Stunden Fa = Dynamic side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281. 012 TG.indd, js 128 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série Code: AM SAE A 2-Bolt, 5/16-18 UNC Manifold "L" 64.3 (2.53) 15.7 (.62) 31.75 (1.250) ø129.5 (5.10) Max 2.7 (.11) 106.4 (4.188) A A ø 82.55 (3.250) 82.50 (3.248) B 63.50 (2.500) B B 45.7 (1.8) B 14.29 (.563) 28.58 (1.125) 4 x 5/16-18 UNC thd x .500 min deep Code AM disp. 0140 Weight/Gewicht kg 14.2 Poids/Peso (lb) (31.4) Length "L" mm "L" (in) 0170 0195 14.5 14.7 (32.0) (32.5) 196 199 (7.70) 202 (7.82) (7.95) 0240 63.068 (2.483) 0280 0310 0335 0405 0475 0530 133.4 (5.25) ø13.48 (17/32) 0625 0785 0960 15.1 15.5 15.7 15.9 16.5 17.2 17.9 18.6 20.2 21.9 (33.3) (34.2) (34.7) (35.1) (36.4) (37.9) (39.5) (41.1) (44.5) (48.3) 250 267 288 207 211 215 218 225 234 240 (8.13) (8.32) (8.46) (8.57) (8.86) (9.20) (9.45) (9.82) (10.57) (11.32) Code: AS SAE A 2-Bolt, 7/8-14 SAE "L" 64.3 (2.53) 15.7 (.62) 2.7 (.11) 106.4 (4.188) A A ø129.5 (5.10) Max ø 82.55 (3.250) 82.50 (3.248) B B 25.40 (1.000) 7/8-14 SAE O-Ring 63.068 (2.483) Code AS 133.4 (5.25) ø13.48 (17/32) disp. 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 Weight/Gewicht kg 14.2 14.5 14.7 15.1 15.5 15.7 15.9 16.5 17.2 17.9 18.6 20.2 21.9 Poids/Peso (lb) (31.4) (33.3) (34.2) (34.7) (35.1) (36.4) (37.9) (39.5) (41.1) (44.5) (48.3) 207 211 215 218 225 234 240 250 267 288 (8.13) (8.32) (8.46) (8.57) (8.86) (9.20) (9.45) Length "L" mm "L" (in) 196 (7.70) (32.0) (32.5) 199 202 (7.82) (7.95) (9.82) (10.57) (11.32) English equivalents for metric specifications are shown in ( ). 012 TG.indd, js 129 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série Code: LS Wheel, Front Brake Nose, 7/8-14 SAE "L" 4.1 (.16) Min 64.7 (2.55) 36.8 (1.45) 19.1 (.75) 46.7 (1.84) 45˚ ø 76.2 (3.00) ø 126.90 / 127.00 (4.996/5.000) A A ø 88.85 (3.498) 88.80 (3.496) 135.0 (5.314) B B ø 126.6 (4.984) 25.40 (1.000) 147.6 (5.812) 13.49 (17/32) 4 x _5/16-18 UNC v.75 + _ .03 7/8-14 SAE O-Ring Code LS disp. 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 Weight/Gewicht kg 14.6 14.8 15.1 15.5 15.9 16.1 16.3 16.9 17.5 18.3 19.0 20.5 22.2 Poids/Peso (lb) (32.2) (37.7) (33.3) (34.1) (35.0) (35.5) (35.8) (37.2) (38.6) (40.3) (41.8) (45.3) (49.0) 150 154 157 161 166 170 173 180 188 195 204 223 242 (5.92) (6.04) (6.17) (6.35) (6.54) (6.68) (6.79) (7.08) (7.42) (7.67) (8.04) (8.79) (9.54) Length "L" mm "L" (in) Code: MS Magneto, 7/8-14 SAE 63.068 (2.483) "L" 64.3 (2.53) 15.7 (.62) 2.7 (.11) 22˚30´ A 22˚30´ A ø129.5 (5.10) Max ø 82.55 (3.250) 82.50 (3.248) B B 25.40 (1.000) ø106.4 (4.188) 7/8-14 SAE O-Ring Code MS 133.4 (5.25) ø13.48 (17/32) disp. 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 Weight/Gewicht kg 14.2 14.5 14.7 15.1 15.5 16.1 15.9 16.5 17.2 17.9 18.6 20.2 21.9 Poids/Peso (lb) (31.4) (32.0) (32.5) (33.3) (34.2) (35.5) (35.1) (36.4) (37.9) (39.5) (41.1) (44.5) (48.3) 196 199 202 207 211 215 218 225 234 240 250 267 288 (7.70) (7.82) (7.95) (8.13) (8.32) (8.46) (8.57) (8.86) (9.20) (9.45) (9.82) (10.57) (11.32) Length "L" mm "L" (in) English equivalents for metric specifications are shown in ( ). 012 TG.indd, js 130 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série Code: US Wheel, Standard, 7/8-14 SAE "L" 19.1 (.75) 36.8 (1.45) 63.8 (2.513) 46.7 (1.84) 45˚ 39.9 (1.57) 4.1 (.16) Min 6.6 (0.26) ø 82.55 (3.250) 82.50 (3.248) A A ø 62.99 (2.48) ø 126.90 / 127.00 (4.996 / 5.000) 135.0 (5.314) B B 25.40 (1.000) ø 147.6 (5.812) ø 13.48 (17/32) 7/8-14 SAE O-Ring Code US disp. 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 Weight/Gewicht kg 14.6 14.8 15.1 15.5 15.9 16.1 16.3 16.9 17.5 18.3 19.0 20.5 22.2 Poids/Peso (lb) (32.2) (32.7) (33.3) (34.1) (35.0) (35.5) (35.8) (37.2) (38.6) (40.3) (41.8) (45.3) (49.0) Length "L" mm "L" (in) 150 154 157 161 166 170 173 180 188 195 204 223 242 (5.92) (6.04) (6.17) (6.35) (6.54) (6.68) (6.79) (7.08) (7.42) (7.67) (8.04) (8.79) (9.54) Code: WE Wheel, Optional, Manifold Rear Port 19.1 (.75) 4.8 (.19) Min 22.3 (.88) 65.53 (2.580) 28.6 (1.13) 45˚ 8.9 (0.35) 4x5/16-18 UNC ø 126.6 (4.984) 45.72 (1.800) 147.6 (5.812) 44.19 (1.74) A A ø 107.95 (4.250) 107.83 (4.245) B 135 (5.314) B 22.86 (.900) ø 127.00 / 126.90 (5.000 / 4.996) ø 13.48 (17/32) "L" + 24.7 (.972) "W" + 2 kg (4.41 lb) Code WE disp. 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 Weight/Gewicht kg 17.6 17.8 18.1 18.4 18.8 19.1 19.3 19.8 20.5 21.3 22.0 23.5 25.2 Poids/Peso (lb) (38.7) (39.3) (39.8) (40.6) (41.5) (42.0) (42.4) (43.7) (45.2) (46.8) (48.4) (51.8) (55.6) Length "L" mm "L" (in) 178 181 184 189 193 197 200 207 216 222 232 251 270 (6.99) (7.11) (7.24) (7.43) (7.61) (7.75) (7.86) (8.15) (8.49) (8.74) (9.12) (9.87) (10.62) English equivalents for metric specifications are shown in ( ). 012 TG.indd, js 131 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série Code L Code A Code W Code M Code U Code: 01 1" 6B Spline 94.0 (3.70) 48.8 (1.92) 91.4 (3.60) Code: 03 1 1/4" Keyed Code: 05 60.2 (2.37) 105.4 (4.15) 57.4 (2.26) 102.6 (4.04) 102.9 (4.05) 100.1 (3.94) 1" 1/4 14 Tooth Spline Code: 06 106.7 (4.20) 61.5 (2.42) 104.1 (4.10) 19 Tooth Spline English equivalents for metric specifications are shown in ( ). 012 TG.indd, js 132 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes Code: 01 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série 37.34 (1.47) 4.3 (.17) 1.24 (.049) 1" 6B Spline 25.4 (1.0) Min Full Spline Code: 03 21.54 / 21.29 (.848 / .838) 6.18 / 6.27 (.2435 / .2470) 25.32 / 25.02 (.997 / .985) 50.3 (1.98) 36.5 (1.437) x 7.9 (.311) 8.01 / 7.91 (.3155 / .3115) 11.38 / 10.85 (.448 / .427) 1 1/4" Keyed 3.490 (1.374) 31.72 / 31.75 (1.249 / 1.250) _ 5/8-18 UNF 19.05 (.75) v Code: 05 47.2 (1.86) 25.4 (1.0) Min Full Spline 31.06 / 31.75 (1.223 / 1.250) _ 5/8-18 UNF v 19.1 (.75) 1" 1/4 14 Tooth Spline Code: 06 19 Tooth Spline 26.29 / 26.85 (1.035 / 1.057) 3.18 / 3.32 (.1251 / .1309) ø 27.31 (1.075) 28.4 (1.12) 31.01 / 31.32 (1.221 / 1.233) 27.94 / 28.45 (1.100 / 1.120) 27.03 / 27.69 (1.064 / 1.090) _ 2.31 / 2.49 (.0908 / .0982) v10.31 (.406) English equivalents for metric specifications are shown in ( ). 012 TG.indd, js 133 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série Code L Code A Code W Code M Code U Code: 08 1 1/4" Tapered 106.9 (4.21) 61.7 (2.43) 104.4 (4.11) Code: 19 1 3/8" J501 Taper 70.1 (2.76) 115.4 (4.54) 112.8 (4.44) English equivalents for metric specifications are shown in ( ). 012 TG.indd, js 134 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes Code: 08 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TG Series / Serie / Série 5/16x1 SAE J502 1:8 500 Nm (375 Ft Lb) 1 1/4" Tapered ø31.88 (1.255) ø31.75 (1.249) 7.96 / 7.94 (0.313 / 0.312) 3.18 (.125) 35 (1.37) 1-20UNEF 19 (.748) Code: 19 41.48 (1.633) 21.16 (0.833) 7.95 / 7.92 (.313 / .312) 25.4 (1.00) 1 3/8" J501 Taper 3.175 (.125) 35.05 (1.38) 34.93 (1.37) Md = 500 Nm (375 Ft Lb) 1.125-18 UNEF 1:8 English equivalents for metric specifications are shown in ( ). 012 TG.indd, js 135 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica Cont. (to 3000 psi) . . . 207 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque MaxDrehmoment Couple Torque Maximo Exceptional Strength and Durability in a High Performance Motor/Brake Package (8.6 to 58.5 in3/rev) 140 . . . 959 cm3/rev 13 Displacements 13 Schluckvolumen 13 Cylindrée 13 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BG Series Brake Motor This brake motor consists of a BG Series motor integrated into a wet disc, spring applied, hydraulically released brake. Standard holding capacity is 12,000 lb in of holding torque. The brake is front mounted for reliable operation even in the event of a drive link failure. The brake release port is capable of pressures to 3000 PSI. Int. (to 4000 psi) . . . 276 bar (to 30 gpm) . . . 114 lpm (660 rpm) 660 rpm Cont. (9,239 lb in) 1044 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral Int. (12,636 lb in) 1428 Nm (to 3597 lb) . . . 16000 N Rated Brake Holding Capacity @ Zero Release Pressure Nm (in-lbs) Maximum Full Release Pressure bar (PSI) 1350 (12,000) 22 (315) 12,000 in-lbs is standard holding capacity. For other holding capacities, consult the factory for price and availability. CAUTION! See installation/operating instructions for product cautions and proper use. * With optional spring package. 013 BG Brake.indd, js 136 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos BG XXXX LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BG Series Brake Motor X Displacement Mounting/Ports Schluckvolumen Gehäuse/Anschluß Cylindrée Carter/Plan de raccordement Desplazamiento Montaje/Lumbreras Series XX 0 Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion cm3/U cm3/tr Code cm3/giro cu in3/rev 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 141 169 195 238 280 310 337 405 477 528 623 786 959 / / / / / / / / / / / / / 8.6 10.3 11.9 14.5 17.1 18.9 20.6 24.7 29.1 32.3 38.0 48.0 58.5 XXXX Options Opciones Code Front Port Rotation 0 Code Shaft 1 1/4" Keyed Standard Code AAAB 03 AAAA Description No Paint No lackiert Black Paint Schwarz lackiert 1 1/4" 14 Tooth Spline 05 1 1/4" Tapered* Code Mounting/Ports Front Mtg/Front Bolting 1/2-13 UNC Thd, 7/8-14 SAE 08 1 3/8" Tapered* AS 19 SAE 14 Tooth Spline SAE "B" 2 Bolt, Manifold 62 BM Rear Mtg/Thru Bolting, 7/8-14 SAE CS For performance data curves, see TG section. For other available options, see page 187. 013 BG Brake.indd, js 137 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Notes / Hinweis Remarques / Notas LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BG Series Brake Motor 013 BG Brake.indd, js 138 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BG Series Brake Motor Wheel Mount/Radnabengehause Monture à roue/ Montaje de rueda Side Load - N (lbs) 71,171 (16,000) Max Load Curve 62,275 (14,000) 53,378 (12,000) 44,482 (10,000) 35,584 (8,000) 26,688 (6,000) 17,792 (4,000) Dynamic Load Curve 8,896 (2,000) 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Distance from Mounting Face - mm (in) Motor Image Not To Scale The dynamic side load curve is based on uni-directional steady state loads for L10 bearing life at 3 x 106 revolutions. Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 3 x 106 Umdrehungen kalkuliert. La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 3 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 3 x 106 revoluciones. The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. Equation to Calculate the Expected Radial Bearing Life Gleichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 3 x 106 60 x S { FF } 3.33 a b Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min-1 L = Life In Hours / Lebensdauer in Stunden Fa = Dynamic side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281 013 BG Brake.indd, js 139 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BG Series Brake Motor Code: AS Front Mounting / Front Bolting, 7/8-14 SAE O-Ring “L” 99.8 (3.93) 47.2 (1.860) 21.9 (.86) 127.00 (5.000)/ 58.42 126.90 (2.3) (4.996) 87.8 (3.460) 16.8 (.66) 66.55 (2.620) 90˚ 171.5 (6.75) A A B B 185.4 (7.30) ø 190.50 (7.50) ø 13.46(.530) x 39.12 (1.54) Deep 1/2-13 UNC ø 127.0 / 126.90 (5.000 / 4.998) 7/8-14 SAE O-Ring Ports 7/16-20 O-Ring Port 0140 Code AS 0170 0195 0240 0280 0335 0405 0475 0530 0625 0785 0960 kg 27.3 27.5 27.8 28.1 28.5 28.9 29.5 30.2 30.9 31.7 33.2 34.9 (lb) (60.2) (60.8) (61.3) (62.1) (63.0) (63.9) (65.2) (66.7) (68.3) (69.9) (73.3) (77.1) "L"mm "L" (in) 192.3 (7.57) 195.3 (7.69) 198.6 (7.82) 203.2 (8.00) 208.0 (8.19) 214.4 (8.44) 221.7 (8.73) 230.4 (9.07) 236.7 (9.32) 246.1 (9.69) Weight / Gewicht Poids/Peso Length 182.4 (7.18) 265.2 284.2 (10.44) (11.19) Code: BM* SAE "B" 2 Bolt, Manifold "L" 88.14 (3.470) 140.1 (5.55) 110.13 (4.34) 4 x 5/16-18 UNC Thd x 12.70 (.500)Min 14.22 (.560) 61.6 (2.43) 6.22 (.245) ø146.1 (5.75) A Ø127.00 (5.000) 126.90 (4.996) A 185.4 (7.30) 45.72 (1.8) A A 63.5 (2.50) B B 14.29 (.56) 28.58 (1.13) 187.9 (7.40) 15.8 (.620) 40.6 (1.6) o/ 101.60 / 101.50 (4.000 / 3.996) 7/16-20 O-Ring Port Code BM 0140 0170 0195 0240 0280 0335 0405 0475 0530 0625 0785 kg Weight / Gewicht (lb) Poids/Peso Length "L" mm "L" (in) 28.4 28.7 28.9 29.3 29.7 30.1 30.1 30.7 31.3 32.8 34.3 0960 36.1 (62.6) (63.2) (63.7) (64.5) (65.4) (66.3) (67.6) (69.1) (70.7) (72.3) (75.7) (79.5) 233.2 (9.18) 236.4 (9.31) 239.6 (9.43) 244.3 (9.62) 249.1 (9.81) 255.4 (10.06) 262.8 (10.35) 271.3 (10.68) 277.7 (10.93) 287.2 (11.31) 306.3 325.3 (12.06) (12.81) English equivalents for metric specifications are shown in ( ). 013 BG Brake.indd, js 140 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BG Series Brake Motor Code: CS Rear Mounting/Thru Bolting, 7/8-14 SAE O-Ring “L” 99.8 (3.93) 16.8 (.66) 66.55 (2.620) 187.9 (7.40) 47.2 (1.860) 21.9 (.86) 185.4 (7.30) 171.5 (6.75) A A 185.4 (7.30) 58.42 (2.3) Ø127.00 (5.000) 126.90 (4.996) B B ø 13.5 (.530)** 7/16-20 O-Ring Port **Will not support a bolt or nut without a bracket. Code CS 0140 0170 0195 0240 0280 0335 0405 0475 0530 0625 0785 0960 kg 27.3 27.5 27.8 28.1 28.5 28.9 29.5 30.2 30.9 31.7 33.2 34.9 (lb) (60.2) (60.8) (61.3) (62.1) (63.0) (63.9) (65.2) (66.7) (68.3) (69.9) (73.3) (77.1) "L" mm "L" (in) 192.3 (7.57) 195.3 (7.69) 198.6 (7.82) 203.2 (8.00) 208.0 (8.19) 214.4 (8.44) 221.7 (8.73) 230.4 (9.07) 236.7 (9.32) 246.1 (9.69) Weight / Gewicht Poids/Peso Length ø 127.0 / 126.90 (5.000 / 4.998) 7/8-14 SAE O-Ring Ports *Note: Motor with manifold mount is supplied A-A with 2 o-rings. Zum Motor mit Universalanschluß werden 2 o-ringe geliefert. 265.2 284.2 (10.44) (11.19) O-Ring Ø12.37x2.62 1.8 (0.091) Deux joints toriques sont livrés avec les moteurs a plan de raccordement Ø17.3 universel. (0.68) Ø12.7 (0.5) El motor con montaje de distribuidor se suministra con 2 sellos toroidales. English equivalents for metric specifications are shown in ( ). 013 BG Brake.indd, js 141 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BG Series Brake Motor Code A & C Code B Code: 03 1 1/4" Keyed 65.5/63.5 (2.58/2.50) 106.7/104.7 (4.20/4.12) Code: 05 1 1/4" 14 Tooth Spline 106.7/104.7 (4.20/4.12) 65.5/63.5 (2.58/2.50) 107.9/105.9 (4.25/4.17) 66.7/64.7 (2.63/2.55) 110.5/108.5 (4.35/4.27) 69.3/67.3 (2.73/2.65) Code: 08 1 1/4" Taper Code: 19 1 3/8" J501 Taper Code: 62 SAE 14 Tooth Spline 97.6/95.6 (3.84/3.76) 56.4/54.4 (2.22/2.14) English equivalents for metric specifications are shown in ( ). 013 BG Brake.indd, js 142 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BG Series Brake Motor 50.3 (1.98) 36.5 (1.437) x 7.9 (.311) Code: 03 7.912/7.887 (.3115/.3105) 1 1/4" Keyed 3.490 (1.374) 31.72 / 31.75 (1.249 / 1.250) 5/8-18 UNF v19.05 (.75) 42.16 (1.660) Min Full Spline 31.62 / 31.75 (1.245 / 1.250) Code: 05 ø 31.70 (1.248) 1 1/4" 14 Tooth Spline 5/8-18 UNF THD x16.0 (.63) Min Deep 3.178 / 3.325 (.1251 / .1309) 26.29 / 26.85 (1.035 / 1.057) 5/16x1 SAE J502 500 Nm (375 Ft Lb) Max 7.96 / 7.94 See installation Instructions (0.313 / 0.312) ø31.88 (1.255) ø31.75 (1.249) 1:8 Code: 08 3.18 (.125) 1 1/4" Taper 35 (1.37) 1-20UNEF 19 (.748) 35.0 (1.37) 21.16 (0.833) 25.4 (1.00) 7.963/7.938 (.3135 / .3125) Code: 19 3.175 (.125) 1 3/8" J501 Taper 35.05 (1.380) 34.93 (1.375) 500 Nm (375 Ft Lb) Max See installation instructions 1.125-18 UNEF 1:8 45.01 (1.775) Min. 29.0 (1.144) Min Full Spline 25.40 (1.0) 31.06 / 31.75 (1.223 / 1.250) Code: 62 5/8-18 UNF X v (19.1) .75 Min. SAE 14 Tooth Spline Ø 3.18 / 3.32 (.1251 / .1309) 26.29 / 26.85 (1.035 / 1.057) 27.73 (1.080) 27.18 (1.070) English equivalents for metric specifications are shown in ( ). 013 BG Brake.indd, js 143 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica (8.6 to 58.5 in3/rev) 140 . . . 958 cm3/rev 13 Displacements 13 Schluckvolumen 13 Cylindrée 13 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Cont. (to 3000 psi) . . . 207 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque MaxDrehmoment Couple Torque Maximo Int. (to 4000 psi) . . . 276 bar (to 30 gpm) . . . 114 lpm LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DG Series Brake Motor A Mechanical Brake Motor for Tough Applications Parker’s latest DG Series integrated motor is truly another innovation the market has been waiting for. The compact size, reliable holding capability and ease of installation makes this new mechanical brake motor the perfect choice for many turf or agricultural applications using hydraulics for wheel motors. This mechanically applied version of the brake motor is available in 13 motor displacements (8.6 to 58.5 cu./in.). Pressure capacities are up to 280 bar (4,000 psi) intermittent and 210 bar (3,000 psi) continuous. Flows up to 114 lpm (30 gpm) and speed up to 660 rpm are available. Motor output torque up to 1428 Nm (12,636 lb. in.) intermittent and 1044 Nm (9,239 lb. in.) continuous is available. (660 rpm) 660 rpm Cont. (9,239 lb in) 1044 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral Int. (12,636 lb in) 1428 Nm (to 3597 lb) . . . 16000 N Holding capacity is 497 Nm (4,400 in lbs) with 68 Nm (600 in lbs) of input torque at lever pivot. Brake capacities are typical for nonburnished brake shoe. OEM testing required to verify actual field conditions. Das maximale Bremsmoment von 497 Nm (4400 in Ibs) wird erreicht durch Betätigung des Bremshebels mit 68 Nm ( 600 in Ibs). Genannte Einsatzdaten beziehen sich auf Neuprodukte. Die Eignung der Geräte ist vom Anwender für den jeweiligen Einsatz individuell zu prüfen . La puissance de maintien est de 497 Nm (4400 pouces-livres) avec couple d’entrée au pivot du levier de 68 Nm (600 pouces-livres). Les puissances de freinage sont typiques pour des sabots de frein non brunis. Les essais imposés par le constructeur d’origine exigent la vérification des conditions réelles sur place. Capacidad de retención de 497 N-m (4.400 libras-pulgada) con 69 N-m (600 libras-pulgada) de torque de entrada en el brazo de articulación. Los valores de capacidad de frenado son típicas para zapatas de freno no bruñidas. Para fabricantes de equipos originales se deben efectuar pruebas bajo condiciones reales de funcionamiento. 014 DG Brake.indd, js 144 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DG Series Brake Motor .. Wheel Mount/Radnabengehause Monture à roue/ Montaje de rueda Side Load - N (lbs) 71,171 (16,000) Max Load Curve 62,275 (14,000) 53,378 (12,000) 44,482 (10,000) 35,584 (8,000) 26,688 (6,000) 17,792 (4,000) Dynamic Load Curve 8,896 (2,000) 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Distance from Mounting Face - mm (in) Motor Image Not To Scale The dynamic side load curve is based on uni-directional steady state loads for L10 bearing life at 3 x 106 revolutions. Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 3 x 106 Umdrehungen kalkuliert. La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 3 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 3 x 106 revoluciones. The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. Equation to Calculate the Expected Radial Bearing Life Gelichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 3 x 106 60 x S Fa Fb { } 3.33 Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min-1 L = Life In Hours / Lebensdauer in Stunden Fa = Dynamic side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281 014 DG Brake.indd, js 145 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos XXXX DG Series Code 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DG Series Brake Motor XS 8 X 0 XXXX Rotation Shaft Options Drehrichtung Welle Opciones Arbre Direction de rotation Rotacion Eje Drum Type Displacement Mounting/Ports Trommelbremse Schluckvolumen Gehäuse/Anschluß Cylindrée Carter/Plan de raccordement Tipo de tambor Genre de tambour Desplazamiento Montaje/Lumbreras cm3/tr cm3/giro cm3/U cu in3/rev 141 169 195 238 280 310 337 405 477 528 623 786 959 / / / / / / / / / / / / / Code Front Port Rotation 8.6 10.3 11.9 14.5 17.1 18.9 20.6 24.7 29.1 32.3 38.0 48.0 58.5 0 Standard Code AAAB AAAA Code Description No Paint No lackiert Black Paint Schwarz lackiert Mounting/Ports AS Wheel Mt. w/Brake Lever @ 105o/ BS CS DS ES FS GS HS Wheel Mt. w/Brake Lever @ 165o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 195o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 255o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 285o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 345o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 15o / 7/8-14 SAE Wheel Mt. w/Brake Lever @ 75o / 7/8-14 SAE 7/8-14 SAE Code A Drum Type 4 Bolt Code Shaft 1 1/4” Tapered B 5 Bolt 8 For other available options, see page 187. 014 DG Brake.indd, js 146 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DG Series Brake Motor Code: AS Wheel Mount w/Brake Lever / 7/8-14 SAE O-Ring 106.9 (4.21) "L” 36.8 (1.45) 19.1 (.75) Torque Nut to 169 Nm (125 Ft Lbs) Min Plus Rotation to Align Cotter Pin Ø 6.70 (.264) 19.2 (.757) 4.1 (.16) Min 5˚ 50.8 (2.0) 10 60.0 88.85 (3.498) (2.362) 88.80 (3.496) A 127.00 (5.000) Ø 126.90 (4.996) B A B 1/2-20 UNF 7/8-14 SAE O-Ring 13.5 (0.53) Ø 25.40 (1.000) 46.7 (1.84) 95.1 (3.743) 63.83 (2.513) Ø147.62 (5.812) 22.0 (.866) 46.0 (1.811) Note: 1. Brake Acuation Lever can be positioned in 12.00° increments from that shown. Bremshebel ist kreisförmig in Sigmenten von 12.00 ° positionierbar. Le levier de commande du frein peut être positionné à des échelons d’accroissement de 12,00° de ce qui est montré. El brazo de actuación del freno se puede colocar en avances de 12,00 grados con respecto a la posición mostrada. 2. Brake Acuation Lever is shipped unattached, secured with wire or tiewrap to assembly. Hebel ist anbei. Endmontage erforderlich. Le levier de commande du frein est expédié sous forme détachée; il est attaché à l’ensemble avec du fil ou du ruban. El brazo de actuación del freno se suministra suelto, sin conexión, sólo atado provisoriamente al mecanismo. Code AS disp. 0080 0100 0130 0140 0170 0195 0240 0280 0360 0405 0475 Weight/Gewicht kg 18.0 18.1 18.3 18.4 18.7 19.0 19.4 19.7 20.4 21.0 21.7 Poids/Peso (lb) (39.74) (39.84) (40.34) (40.64) (41.14) (41.84) (42.74) (43.34) (45.04) (46.34) (47.74) Length "L" mm "L" (in) 146 146 149 151 154 157 162 167 176 180 189 (5.73) (5.73) (5.85) (5.92) (6.04) (6.17) (6.35) (6.54) (6.92) (7.08) (7.42) For performance data curves, see TG section. English equivalents for metric specifications are shown in ( ). 014 DG Brake.indd, js 147 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Dimensional Data/Abmessungen Metrage/Datos de dimensiones ' LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DG Series Brake Motor Drum Type/Trommelbremse/ Tipo de tambor/ Genre de Tambour Code: A Code: B 4 X ½-20 UNF 4 Bolt 5 X ½-20 UNF Ø114.3 (Ø4.500) 5 Bolt 1/8 X 50.8 (2.00) COTTER PIN Ø165.48 (Ø6.515) 1/8 X 50.8 (2.00) COTTER PIN Ø101.6 (Ø4.000) Ø165.48 (Ø6.515) Shafts / Abtriebswellen Arbre / Ejes Code: 8 1 1/4" Taper 106.9 (4.21) 5/16x1 SAE J502 8.01 (.3155) 7.91 (.3115) 1:8 ø31.88 (1.255) ø31.75 (1.249) 35 (1.37) 7.62 (.300) 7.21 (.284) 1-20 UNEF 19 (.748) English equivalents for metric specifications are shown in ( ). 014 DG Brake.indd, js 148 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU DG Series Brake Motor 014 DG Brake.indd, js 149 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica (8.6 to 58.5 in3/rev) 141 . . . 959 cm3/rev 13 Displacements 13 Schluckvolumen 13 Cylindrée 13 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Cont. (to 3000 psi) . . . 207 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque MaxDrehmoment Couple Torque Maximo Int. (to 4000 psi) . . . 276 bar LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série A Rugged Motor for Heavy Duty, High Side Load Applications This motor was designed for tough applications. A stout drive link with patented 60:40 spline geometry will transmit over 13,000 lb-in of torque. The 1-1/2" output shaft can support 7000 pounds of radial load. Efficiency is assured by the use of roller vanes and sealed commutator. Durability is maintained by continually washing the powertrain splines and shaft seal in cooling fluid. (to 30 gpm) . . . 114 lpm (660 rpm) 660 rpm Cont. (8,772 lb in) 991 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral Int. (11,876 lb in) 1342 Nm (to 4800 lb) . . . 21360 N 015 TH.indd, js 150 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l Cil ndré luck acem ind e vo lum ent Ma rata en x. Ma spe ed x. Vit Dre @ M e h Ve sse d zahl ax. i loc e r Inte nte rm ida ot d m atio rmitt itte Ma ax n m iere nt fl x. im nd o Ma oil a a axi er w flo x Be ca Dé . Sch w t rie ud b lu al b: Po it d´h cks int t r ta e r u rm ta ile m om it e ma Ma nte x axi x. ma d Ma iff x im er x o Ch . Dru enti a u c l Pr te de kgef pres es ä ion pre lle sure dif ssio Ma e re n m x nc Ma . sup ia l a x i x. ply ma E Pr p i n x im r es ga e a Pr sion ngs ssur es e ion max druc ma i en k Ma x im t ré x ad e Ma . torq ea x. u e lim Co Dre en up hm tac To le m om ion rqu e a nt e M xi ax Ma im x o Ma . per for x. L m Pu is eist anc Po sanc unga e ten e b za de gab me sor e Mi n. c c t ie an Mi star ica max n. t i ma i Co Anla ng to x up ufm rqu l To e m o rqu me e i n e m . fo nt ini urn mo i a de u dé a rr m an anr qu e age LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série max bar psi cont / int* Nm lb-in 276 4000 300 4350 390 3455 530 4692 33 45 315 2791 418 3706 207 3000 276 4000 300 4350 476 4216 646 5714 33 45 376 3331 505 4469 95 25 207 3000 276 4000 300 4350 556 4919 753 6663 33 45 451 3989 611 5408 76 20 95 25 207 3000 276 4000 300 4350 677 5991 913 8081 32 44 582 5152 776 6865 334 76 20 95 25 207 3000 276 4000 300 4350 796 7044 1073 9499 31 42 675 5972 870 7699 310 18.9 303 76 20 95 25 207 3000 276 4000 300 4350 964 8533 1297 11479 30 41 843 7458 1117 9889 TH 0335 337 20.6 277 76 20 95 25 207 3000 276 4000 300 4350 924 8184 1229 10817 31 41 778 6882 1005 8893 TH 0405 405 24.7 232 76 20 95 25 172 2500 241 3500 300 4350 942 8336 1342 11877 27 37 791 7002 1145 10133 TH 0475 477 29.1 237 76 20 114 30 138 2000 207 3000 300 4350 887 7853 1372 12145 28 38 740 6549 1120 9909 TH 0530 528 32.3 213 76 20 114 30 138 2000 172 2500 300 4350 983 8701 1253 11086 23 31 874 7737 1091 9657 TH 0625 623 38.0 182 76 20 114 30 121 1750 155 2250 300 4350 986 8727 1291 11424 20 27 895 7924 1165 10312 TH 0785 786 48.0 143 76 20 114 30 103 1500 138 2000 300 4350 1044 9239 1428 12636 17 23 991 8772 1341 11876 TH 0960 959 58.5 118 76 20 114 30 69 1000 103 1500 300 4350 773 6843 1268 11227 12 16 763 6752 1177 10419 cont / int* l/min g/min cont / int* bar psi Motor Series TH cm3/rev in3/rev rev/min TH 0140 141 8.6 660 76 20 95 25 207 3000 TH 0170 169 10.3 554 76 20 95 25 TH 0195 195 11.9 477 76 20 TH 0240 238 14.5 393 TH 0280 280 17.1 TH 0310 Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. * Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. max KW HP cont / int* Nm lb-in Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 015 TH.indd, js 151 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TH XXXX XX Displacement Mounting/Ports Schluckvolumen Gehäuse/Anschluß Cylindrée Carter/Plan de raccordement Desplazamiento Montaje/Lumbreras Series Code LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série cm3/U cm3/tr cm3/giro cu in3/rev 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 141 169 195 238 280 310 337 405 477 528 623 786 959 Code / / / / / / / / / / / / / 8.6 10.3 11.9 14.5 17.1 18.9 20.6 24.7 29.1 32.3 38.0 48.0 58.5 Code XX 0 XXXX Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion Options Opciones Code Front Port Rotation Shaft 1 1/2" J501 Taper 0 Standard 31 1 1/2" Keyed 32 Code 1 1/2" 17 Tooth 12/24 Spline AAAB AAAA 36 No Paint No lackiert Black Paint Schwarz lackiert Mounting/Ports Magneto, 7/8-14 SAE MS SAE "B" 4 Bolt, Axial PA* Wheel, Standard, 7/8-14 SAE US * Requires rear porting. Nur Endanschluss moglich Exige des orifices en arriere Necesita lumbrera posterior For other available options, see pages 182-187. 015 TH.indd, js 152 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série TH 0140 Flow [G/min] 15 Schluckstrom [L/min] 2 10 20 30 40 50 60 70 76 80 .5 3 90 95 7 5 12 9 US 20 25 5000 600 4500 500 280 4000 240 3500 210 3000 4000 140 200 3000 2500 2500 2000 2000 psi 170 bar Drehmoment [Nm] 300 Torque [lb/in] 3500 400 1500 1500 100 1000 100 1000 70 35 700 0 0 100 200 300 400 Drehzahl [1/min] 500 500 600 500 0 0 100 200 300 400 500 600 700 Speed [Rpm] TH 0170 Schluckstrom [L/min] 2 20 10 30 40 50 60 70 76 80 .5 2 3 6000 90 95 700 5 9 7 12 Flow [G/min] 15 20 US 25 500 240 Torque [lb/in] 170 300 4000 4500 3500 4000 210 400 5000 140 200 3000 3500 3000 2500 psi 280 bar Drehmoment [Nm] 5500 600 2500 2000 2000 1500 100 1500 1000 100 70 0 100 200 300 400 500 500 0 35 600 0 1000 500 0 50 100 150 200 250 300 350 400 450 500 550 600 Speed [Rpm] Drehzahl [1/min] TH 0195 2 10 20 30 40 Schluckstrom [L/min] 50 60 70 76 80 .5 3 7000 90 95 800 5 9 7 12 Flow [G/min] 15 US 20 25 6500 700 4000 6000 280 500 210 400 170 4500 140 300 3500 5000 3000 4000 2500 3500 psi 240 Torque [lb/in] 600 bar Drehmoment [Nm] 5500 3000 2000 2500 2000 200 100 1500 70 1000 100 1000 500 35 50 100 150 200 250 300 350 400 450 0 500 50 100 150 200 250 300 350 400 450 500 Speed [Rpm] Drehzahl [1/min] Cont. 500 0 0 0 1500 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 015 TH.indd, js 153 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série TH 0240 2 10 20 40 30 Schluckstrom [L/min] 60 50 70 76 80 90 95 1000 9000 900 7 5 12 9 Flow [G/min] 15 US 20 25 8000 280 4000 800 7000 700 240 600 210 500 170 3500 400 140 3000 5000 2500 psi Torque [lb/in] 6000 bar Drehmoment [Nm] .5 3 4000 2000 3000 300 100 2000 70 1000 200 100 1500 1000 500 35 0 0 0 50 100 150 200 250 300 350 0 400 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 Speed [Rpm] Drehzahl [1/min] TH 0280 2 10 20 30 40 Flow [G/min] Schluckstrom [L/min] 60 50 70 76 80 90 95 0.5 3 10000 1200 7 5 12 9 15 20 US 25 1100 9000 1000 4000 280 8000 900 3500 240 170 500 Torque [lb/in] 600 bar Drehmoment [Nm] 210 700 140 400 300 100 200 70 100 35 50 100 150 200 250 300 3000 5000 2500 4000 2000 3000 1500 2000 1000 1000 0 0 6000 psi 7000 800 500 0 350 0 50 100 150 200 Speed [Rpm] Drehzahl [1/min] 250 300 350 TH 0310 Schluckstrom [L/min] 2 5 10 1400 20 30 50 40 60 70 76 80 90 95 0.5 12 3 4 5 13000 7 9 12 Flow [G/min] 15 US 20 25 12000 1200 11000 10000 9000 210 8000 170 600 140 Torque [lb/in] 800 240 400 4000 3500 3000 7000 psi 1000 bar Drehmoment [Nm] 280 2500 6000 5000 2000 4000 100 70 200 35 Cont. 50 100 150 Drehzahl [1/min] 200 250 1500 2000 1000 1000 0 0 3000 500 0 300 0 Int. 50 100 150 Speed [Rpm] 200 250 300 Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 015 TH.indd, js 154 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série TH 0335 1400 20 40 30 50 60 70 76 80 .5 3 90 95 5 9 7 US Flow [G/min] 15 20 Schluckstrom [L/min] 2 10 12 25 13000 12000 11000 280 1000 240 9000 210 8000 4000 Torque [lb/in] 800 170 600 bar Drehmoment [Nm] 10000 140 3500 3000 7000 6000 2500 5000 2000 psi 1200 4000 400 100 200 1500 3000 2000 70 1000 1000 35 0 50 100 150 Drehzahl [1/min] 200 250 500 0 0 0 300 50 100 150 200 250 300 Speed [Rpm] TH 0405 2 10 20 US 30 40 Schluckstrom [L/min] 50 70 76 80 60 Flow [G/min] 90 95 1400 13000 .5 3 7 5 12 9 15 20 25 12000 240 1200 1000 3500 10000 3000 9000 8000 600 100 400 70 200 35 2500 7000 psi 140 Torque [lb/in] 170 800 bar Drehmoment [Nm] 11000 210 2000 6000 5000 1500 4000 3000 1000 2000 1000 0 0 50 100 150 200 500 0 250 0 50 100 Speed [Rpm] Drehzahl [1/min] 150 200 250 TH 0475 2 10 20 30 Schluckstrom [L/min] 50 60 70 76 80 40 90 100 114 .5 3 13000 1600 5 7 9 12 US Flow [G/min] 15 20 25 30 12000 1400 11000 10000 210 1000 Torque [lb/in] 8000 170 800 140 bar Drehmoment [Nm] 3000 9000 600 2000 6000 5000 1500 4000 100 400 2500 7000 psi 1200 3000 70 1000 2000 200 1000 35 0 0 25 Cont. 50 75 100 125 150 Drehzahl [1/min] 175 200 225 500 0 0 250 25 50 75 100 125 Speed [Rpm] 150 175 200 225 250 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 015 TH.indd, js 155 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série TH 0530 2 10 20 30 Schluckstrom [L/min] 50 60 70 76 80 40 90 100 114 .5 13000 1400 3 5 7 9 US Flow [G/min] 15 20 12 25 30 12000 1200 11000 10000 170 9000 2500 140 600 100 7000 2000 6000 5000 psi Torque [lb/in] 8000 800 bar Drehmoment [Nm] 1000 1500 4000 400 3000 70 1000 2000 200 1000 0 0 20 40 60 80 100 120 Drehzahl [1/min] 140 160 180 200 500 0 35 220 0 25 50 75 100 125 Speed [Rpm] 150 Flow [G/min] 20 25 175 200 225 TH 0625 2 10 1400 20 US 30 40 50 Schluckstrom [L/min] 60 70 76 80 90 100 114 13000 .5 3 5 7 9 12 15 30 12000 11000 1200 10000 9000 150 2250 8000 120 600 100 7000 1750 6000 psi Torque [lb/in] 800 bar Drehmoment [Nm] 1000 1500 5000 4000 400 3000 70 1000 2000 200 1000 0 0 25 50 75 100 Drehzahl [1/min] 125 150 175 0 35 200 0 20 40 60 80 100 120 140 160 180 Speed [Rpm] TH 0785 2 10 20 30 40 50 Schluckstrom [L/min] 60 70 76 80 90 100 500 200 114 1600 14000 .5 3 5 7 9 12 15 Flow [G/min] 20 US 25 30 13000 1400 12000 11000 1200 10000 2000 9000 100 600 7000 1500 6000 5000 4000 70 400 8000 psi 800 Torque [lb/in] 1000 bar Drehmoment [Nm] 140 1000 3000 2000 200 1000 0 0 Cont. 25 50 75 Drehzahl [1/min] 100 125 0 35 150 0 25 50 75 Speed [Rpm] 100 125 500 150 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 015 TH.indd, js 156 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série TH 0960 2 10 20 30 40 Schluckstrom [L/min] 50 60 70 76 80 90 100 114 13000 1400 .5 3 5 7 9 12 Flow [G/min] 15 20 US 25 30 12000 11000 1200 10000 9000 100 70 7000 psi Torque [lb/in] 600 1500 8000 800 bar Drehmoment [Nm] 1000 6000 5000 1000 4000 400 3000 2000 200 1000 35 0 0 Cont. 20 40 60 Drehzahl [1/min] 80 100 0 0 120 25 50 Speed [Rpm] 75 100 500 125 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.). Performance data is typical. Actual data may vary slightly from one production motor to another. Leistungsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst bei 54oC. Geringfuegige Abweichungen von den Katalogdaten sind moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 015 TH.indd, js 157 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série Flange Mount / Standardgehäuse Monture à bride(s) / Montaje de brida Wheel Mount / Radnabengehäuse Monture à roue / Montaje de rueda Side Load - N (lbs) Side Load - N (lbs) 71,171 (16,000) 71,171 (16,000) Max Load Curve 62,275 (14,000) 53,378 (12,000) 53,378 (12,000) 44,482 (10,000) 44,482 (10,000) 35,584 (8,000) 35,584 (8,000) 26,688 (6,000) 26,688 (6,000) 17,792 (4,000) Dynamic Load Curve Max Load Curve 62,275 (14,000) 17,792 (4,000) Dynamic Load Curve 8,896 (2,000) 8,896 (2,000) 0 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Distance from Mounting Face - mm (in) Motor Image Not To Scale The dynamic side load curve is based on uni-directional steady state loads for L10 bearing life at 6 x 106 revolutions. Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 6 x 106 Umdrehungen kalkuliert. La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 6 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 6 x 106 revoluciones. Distance from Mounting Face - mm (in) Motor Image Not To Scale The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. Equation to Calculate the Expected Radial Bearing Life Gleichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 6 x 106 60 x S { FF } 3.33 a b Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min -1 L = Life In Hours / Lebensdauer in Stunden Fa = Dynamic side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281. 015 TH.indd, js 158 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série Code: MS Magneto, 7/8-14 SAE O-Ring 63.068 (2.483) "L" 64.3 (2.53) 15.7 (.62) 2.7 (.11) 22˚30´ 22˚30´ A A ø129.5 (5.10) Max ø 82.55 (3.250) 82.50 (3.248) B B 7/8-14 SAE O-Ring Code MS 106.4 (4.188) 25.40 (1.000) 133.4 (5.25) ø13.48 (17/32) disp. 0140 0170 0195 0240 0280 0335 0405 0475 0530 0625 0785 0960 Weight/Gewicht kg 14.7 14.9 15.2 15.5 15.9 16.3 16.9 17.6 18.3 19.0 20.6 22.3 Poids/Peso (lb) (32.3) (32.8) (33.4) (34.2) (35.1) (35.9) (37.3) (38.7) (40.4) (41.9) (45.4) (49.1) 216 219 222 227 232 238 245 254 260 270 289 308 (8.50) (8.62) (8.75) (8.94) (9.12) (9.37) (9.66) (10.00) Length "L" mm "L" (in) (10.25) (10.62) (11.37) (12.12) Code: US Wheel, Standard, 7/8-14 SAE O-Ring "L" 19.1 (.75) 64.7 (2.55) 46.7 (1.84) 36.8 (1.45) 45˚ 39.9 (1.57) 4.1 (.16) Min 6.6 (0.26) ø 82.55 (3.250) 82.50 (3.248) A ø 127.00 / 126.90 (5.000 / 4.996) A ø 62.99 (2.48) ø 126.6 (4.984) B B 25.40 (1.000) 7/8-14 SAE O-Ring Code US 135 (5.314) 147.6 (5.812) ø 13.48 (17/32) disp. 0140 0170 0195 0240 0280 0335 0405 0475 0530 0625 0785 0960 Weight/Gewicht kg 16.9 17.2 17.4 17.8 18.2 18.6 19.2 19.8 20.6 21.3 22.9 24.5 Poids/Peso (lb) (37.3) (37.8) (38.4) (39.2) (40.1) (40.9) (42.3) (43.7) (45.4) (46.9) (50.4) (54.1) 173 177 180 184 189 196 203 212 218 227 246 265 (6.82) (6.95) (7.07) (7.26) (7.45) (7.70) (7.99) (8.32) (8.57) (8.95) (9.70) (10.45) Length "L" mm "L" (in) English equivalents for metric specifications are shown in ( ). 015 TH.indd, js 159 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série Code: PA SAE "B" 4 Bolt, Rear 7/8'14 SAE O-Ring Axial "L" 65.5 (2.58) 8.13 (.32) 4.9 (0.19) 15.75 (.62) ø14.53 (.572) 45˚ A 43.2 (1.7) 118.3 (4.66) ø 101.60 / 101.55 (4.000 / 3.998) B 7/8-14 UNF, O-Ring Code PA ø 127.0 (5.000) disp. 0140 0170 0195 0240 0280 0335 0405 0475 0530 0625 0785 0960 Weight/Gewicht kg 16.9 17.2 17.4 17.8 18.2 18.6 19.2 19.8 20.6 21.3 22.9 24.5 Poids/Peso (lb) (37.3) (37.8) (38.4) (39.2) (40.1) (40.9) (42.3) (43.7) (45.4) (46.9) (50.4) (54.1) 235 238 242 246 251 257 265 273 280 289 308 327 (9.26) (9.38) (9.51) (9.70) (9.88) (10.13) Length "L" mm "L" (in) (10.43) (10.76) (11.01) (11.39) (12.14) (12.89) English equivalents for metric specifications are shown in ( ). 015 TH.indd, js 160 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Notes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série English equivalents for metric specifications are shown in ( ). 015 TH.indd, js 161 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série Code U Code P Code M Code: 31 1 1/2" J501 Taper 78.3 (3.08) 120.7 (4.75) 85.7 (3.36) Code: 32 1 1/2" Keyed 63.8 (2.51) 106.2 (4.18) 70.9 (2.79) Code: 36 1 1/2" 17 Tooth 12/24 Spline 63.5 (2.50) 106.2 (4.18) 70.9 (2.79) English equivalents for metric specifications are shown in ( ). 015 TH.indd, js 162 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TH Series / Serie / Série 48 (1.89) Code: 31 33.3 (1.31) 9.50 / 9.47 (.374 / .373) .374 Square Key 500Nm (375 Ft Lb) Max See installation instructions 1 1/2" J501 Taper 4.00 / 3.45 (0.157 / 0.136) 38.100 / 38.075 (1.5 / 1.499) 23 (0.9) 62.74 (2.47) 1.25-18 UNEF 1:8 50.0 (1.97) 36.5 (1.44) Code: 32 4.29 (.169) 9.50 / 9.47 (.374 / .373) .374 Square Key 1 1/2" Keyed 42.05 / 41.55 (.1.655 / 1.636) 38.100 / 38.075 (1.500 / 1.499) 19.0 (0.75) 7/8-14 UNF Code: 36 ø 33.27 / 33.02 (1.310 / 1.300) ø 37.41 / 38.10 (1.473 / 1.500) 41.66 (1.64) Min Full Spline 34.0 (1.339) 1 1/2" 17 Tooth 12/24 Spline 3.18 / 3.32 (.1251 / .1309) _ ø 32.64 / 33.20 (1.285 / 1.307) 5/8-18 UNFv 19.05 (.75) English equivalents for metric specifications are shown in ( ). 015 TH.indd, js 163 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica 13 Displacements 13 Schluckvolumen 13 Cylindrée 13 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima (8.6 to 58.5 in3/rev) 141 . . . 959 cm3/rev Cont. (to 3000 psi) . . . 207 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque MaxDrehmoment Couple Torque Maximo Int. (to 4000 psi) . . . 276 bar LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BH Series Brake Motor Exceptional Strength and Durability in a High Performance Motor/Brake Package This brake motor consists of a BH Series motor integrated into a wet disc, spring applied, hydraulically released brake. Standard holding capacity is 16,000 lb in of holding torque. The brake is front mounted for reliable operation even in the event of a drive link failure. The brake release port is capable of pressures to 3000 PSI. (to 30 gpm) . . . 114 lpm (660 rpm) 660 rpm Cont. (9,239 lb in) 1044 Nm Maximumg Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral Int. (12,636 lb in) 1428 Nm (to 4790 lb) . . . 21306 N Rated Brake Holding Capacity @ Zero Release Pressure Nm (in-lbs) Maximum Full Release Pressure bar (PSI) 1800 (16,000) 22 (315) 16,000 in-lbs is standard holding capacity. For other holding capacities, consult the factory for price and availability. CAUTION! See installation/operating instructions for product cautions and proper use. 016 BH Brake.indd, js 164 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos BH XXXX X Displacement Mounting/Ports Schluckvolumen Gehäuse/Anschluß Cylindrée Carter/Plan de raccordement Desplazamiento Montaje/Lumbreras Series cm3/U cm3/tr Code cm3/giro cu in3/rev 0140 0170 0195 0240 0280 0310 0335 0405 0475 0530 0625 0785 0960 Code LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BH Series Brake Motor 141 169 195 238 280 310 337 405 477 528 623 786 959 / / / / / / / / / / / / / 8.6 10.3 11.9 14.5 17.1 18.9 20.6 24.7 29.1 32.3 38.0 48.0 58.5 Code XX 0 XXXX Shaft Welle Arbre Eje Rotation Drehrichtung Direction de rotation Rotacion Options Opciones Shaft 1 1/2" J501 Taper1 31* 1 1/2" Keyed 32 * Castle nut available on Tapered Shafts Only. Ecrou a creneaux degages disponible pour l'arbre conique seulement Solo eje conico viene con tuerca entallada 1 See installation instructions. Code Front Port Rotation Mounting/Ports Front Mtg/Front Bolting 1/2-13 UNC Thd, 7/8-14 SAE 0 Standard AS Rear Mtg/Thru Bolting, 7/8-14 SAE Code CS AAAB AAAA Description No Paint No lackiert Black Paint Schwarz lackiert For performance data curves, see TH section. For other available options, see page 187. 016 BH Brake.indd, js 165 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BH Series Brake Motor Wheel Mount/Radnabengenhause Monture à roue/ Montaje de rueda Side Load - N (lbs) 71,171 (16,000) Max Load Curve 62,275 (14,000) 53,378 (12,000) 44,482 (10,000) 35,584 (8,000) 26,688 (6,000) 17,792 (4,000) Dynamic Load Curve 8,896 (2,000) 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Distance from Mounting Face - mm (in) Motor Image Not To Scale The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. The dynamic side load curve is based on uni-directional steady state loads for L10 bearing life at 6 x 106 revolutions. Die zulässige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhältnissen auf eine L10 Lebensdauer mit 6 x 106 Umdrehungen kalkuliert. La courbe de charge latérale permise se base sur des charges unidirectionnelles en régime permanent pour le roulement L10 à 6 x 106 révolutions. La curva de valores admisibles de carga lateral está basada en cargas constantes para cojinetes L10 a 6 x 106 revoluciones. Equation to Calculate the Expected Radial Bearing Life Gleichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb, und S in die nachstehende Formel. L = 6 x 106 60 x S { FF } 3.33 a b Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min-1 L = Life In Hours / Lebensdauer in Stunden Fa = Dynamic side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281 016 BH Brake.indd, js 166 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BH Series Brake Motor Code: AS Front Mounting / Front Bolting, 7/8-14 SAE O-Ring "L" 106.2 (4.18) Ø127.00 (5.000) 126.90 (4.996) 185.4 (7.30) 72.9 (2.87) 27.0 (1.06) 34.29 (1.350) 52.6 (2.07) 87.8 (3.460) 90˚ A A 171.5 (6.75) B B 58.4 (2.3) Ø190.50 (7.50) 7/8-14 SAE O-Ring Ports Ø127.00/126.90 (5.000/4.996) Ø13.46(.530) x 39.12 (1.54) x 1/2-13 UNC 7/16-20 O-Ring Port Code AS kg (lb) "L" mm (in) "L" Weight/Gewicht Poids/Peso Length 182.4 (7.18) 0140 0170 0195 0240 0280 0335 0405 0475 0530 0625 27.3 (60.2) 198.6 (7.82) 27.5 (60.8) 201.7 (7.94) 27.8 (61.3) 205.0 (8.07) 28.1 (62.1) 209.6 (8.25) 28.5 (63.0) 214.4 (8.44) 28.9 (63.9) 220.7 (8.69) 29.5 (65.2) 228.1 (8.98) 30.2 (66.7) 236.7 (9.32) 30.9 (68.3) 243.1 (9.57) 31.7 (69.9) 252.5 (9.94) 0785 0960 33.2 34.9 (73.3) (77.1) 271.5 290.6 (10.69) (11.44) Code: CS Rear Mounting/Thru Bolting, 7/8-14 SAE O-Ring "L" 106.2 (4.18) 72.9 (2.87) 27.0 (1.06) 187.9 (7.40) A 185.4 (7.30) Ø127.00 (5.000) 126.90 (4.996) 185.4 (7.30) 34.29 (1.350) 52.6 (2.07) A 171.5 (6.75) B B 58.4 (2.3) 7/8-14 SAE O-Ring Ports 4 X ø 13.5 (.530) Ø127.00/126.90 (5.000/4.996) 7/16-20 O-Ring Port Code CS kg (lb) "L" mm (in) "L" Weight/Gewicht Poids/Peso Length 0140 0170 0195 0240 0280 0335 0405 0475 0530 0625 27.3 (60.2) 198.6 (7.82) 27.5 (60.8) 201.7 (7.94) 27.8 (61.3) 205.0 (8.07) 28.1 (62.1) 209.6 (8.25) 28.5 (63.0) 214.4 (8.44) 28.9 (63.9) 220.7 (8.69) 29.5 (65.2) 228.1 (8.98) 30.2 (66.7) 236.7 (9.32) 30.9 (68.3) 243.1 (9.57) 31.7 (69.9) 252.5 (9.94) 0785 0960 33.2 34.9 (73.3) (77.1) 271.5 290.6 (10.69) (11.44) English equivalents for metric specifications are shown in ( ). 016 BH Brake.indd, js 167 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BH Series Brake Motor Code: 31 130.0 (5.12) 1 1/2" J501 Taper Code: 32 116.4 (4.58) 1 1/2" Keyed 48 (1.89) 25.4 (1.0) .374 Square Key Code: 31 9.50 / 9.47 (.374 / .373) Md: 500Nm (370 Ft Lb) 1 1/2" J501 Taper 38.100 / 38.075 (1.5 / 1.499) 4.00 / 3.45 (0.157 / 0.136) 23 (0.9) 1.25-18 UNEF 1:8 50.0 (1.97) 36.5 (1.44) 8.1 (.319) 4.29 (.169) .374 Square Key Code: 32 9.50 / 9.47 (.374 / .373) 1 1/2" Keyed 38.100 / 38.075 (1.500 / 1.499) 42.05 / 41.55 (1.655 / 1.636) 19.0 (0.75) 7/8-14 UNF English equivalents for metric specifications are shown in ( ). 016 BH Brake.indd, js 168 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Notes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU BH Series Brake Motor 016 BH Brake.indd, js 169 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni/Informacion Tecnica (15.3 to 61.0 in3/rev) 250 . . . 1000 cm3/rev 7 Displacements 7 Schluckvolumen Cylindrée 7 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Pressione in entrata Cont. (to 3500 psi) . . . 241 bar Maximum Oil Flow Schluckstrom Débit d’huile Portata Exceptional Strength and Durability in a High Performance Motor The heart of Parker’s TK Series powertrain, the torque link, is an extra heavy duty part that includes patented 60:40 spline geometry. Rugged construction throughout allows the transmission of over 23,000 lb-in of torque. The entire powertrain is continually washed in cool, high flow fluid to assure long life. Roller vanes and sealed commutator maintain high efficiency and provide smooth low speed performance. (to 60 gpm) . . . 227 lpm Maximum Speed Drehzahl Velocità di rotazione Vitesse de rotation Maximum Torque MaxDrehmoment Couple Coppia Int. (to 4500 psi) . . . 310 bar LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série (523 rpm) 523 rpm Cont. (21360 lb in) 2413 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carico radiale Int. (23540 lb in) 2660 Nm (to 5900 lb) . . . 26245 N 017 TK.indd, js 170 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l De ndré luck acem sp e v olu ent az am me Ma i n en x tos Ma . spe e x Ve . Dre d @ loc hz Ma Ve ità ahl x. i n loc di In ida rot term term d m azio itt itte Ma x ax ne iere nt fl im Ma . oil n a a max der ow x. flow ca Fon Bet Dé Sch u bit lu da ctio rieb Ca d´h cks l in : n t ud ter nem r u al ile m om mi e M ten nt i Ma ax ax te nte x. im i ma rm d o Ma iff de x im it t e ere x. Ac nt: o Ch Dru nti e a i u te c l Pr te de kgef pres es ä ion pre lle sure dif ssio Ma e re n m x nc Ma . sup ia l a x i x. ply ma E Pr p i n xim r es ga e a Pr sion ngs ssur es e ion max druc ma i en k Ma x im t ré x ad e Ma . torq ea x. u e lim Co Dre en up hm ta c To le m om ion rqu e a nt e M xi ax Ma im x o Ma . per for x. L m Pu is eist anc Ma sanc unga e xim e d bg o r e s abe Mi ed ort n. inm ie Mi star ien max n. tin to i A g Co nla t o u To ple ufmo rque rqu mi m e m n. f ent ini our mo ni de au d a rr é m an qu anra ge e LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série Motor Series TK cm3/rev in3/rev cont / int* l/min g/min cont / int* bar psi max bar psi cont / int* Nm lb-in max KW HP cont / int* Nm lb-in rev/min TK 0250 250 15.3 523 114 30 133 35 241 3500 328 4750 814 7204 1043 9234 48.5 65.0 689 6100 879 7780 TK 0315 315 19.2 413 114 30 133 35 241 3500 310 4500 328 4750 1029 9105 1314 11625 47.4 63.5 949 8400 1217 10770 TK 0400 400 24.4 373 114 30 151 40 207 3000 276 4000 328 4750 1153 1524 10201 13484 48.7 65.3 1049 9280 1410 12480 TK 0500 500 30.5 298 114 30 151 40 207 3000 276 4000 328 4750 1439 1914 12736 16940 48.1 64.5 1322 1783 11700 15780 TK 0630 630 38.4 237 114 30 151 40 207 3000 224 3250 328 4750 1617 1716 14313 15187 33.7 45.2 1497 1621 13250 14350 TK 0800 800 48.8 276 151 40 227 60 190 2750 207 3000 328 4750 1916 2300 16960 20360 44.4 59.5 1745 1902 15440 16834 TK 1000 1000 61.0 218 151 40 227 60 172 2500 190 2750 328 4750 2413 2660 21360 23540 35.4 47.5 1981 2180 17535 19290 310 4500 Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. * Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Leistugsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 017 TK.indd, js 171 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos TK XXXX Displacement Schluckvolumen Cylindrée Desplazamiento Series Code X5 Mounting/Rear Ports Gehäuse/Endanschluß Carter/Alimentazione Laterale Montaje/Orifices arriér cm3/tr cm3/giro cm3/U cu in3/rev 0250 0315 0400 0500 250 315 400 500 / / / / 0630 0800 1000 630 / 38.4 800 / 48.8 1000 / 61.0 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série 15.3 19.2 24.4 30.5 XX 0 XXXX Shaft Welle Arbre Ejes Rotation Drehrichtung Direction de rotation Rotacion Options Opciones Code Rear Port Rotation B Code Shaft 0 A Standard 1 1/2" Keyed 32 1 1/2" 17 Tooth 12/24 Spline 36 1 3/4" Tapered Code AAAB AAAA Options No Paint No lackiert Black Paint Schwarz lackiert 63 Code Mounting Standard SAE CC, 1 5/16-12 SAE Rear Radical 40mm Keyed 64 K5 Wheel Mount, 1 5/16-12 SAE Rear Radical T5 For other available options, see pages 189. 017 TK.indd, js 172 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série TK 0250 US Schluckstrom [L/min] 2 510 20 30 1100 70 50 90 Flow [G/min] 110 114 0.5 1 2 4 130 8 16 12 20 24 28 30 32 35 9000 4500 800 280 700 240 600 210 500 170 400 7500 4000 200 100 100 70 0 0 100 200 300 400 3000 4500 2500 3000 140 300 2000 1500 1500 1000 500 0 35 600 500 3500 6000 psi 310 Torque [lb/in] 900 bar 0 100 200 300 400 500 600 Speed [Rpm] Drehzahl [1/min] TK 0315 Schluckstrom [L/min] 20 30 50 70 110 114 90 0.51 2 4 12000 130 16 12 Flow [G/min] 24 20 US 28 30 32 35 11000 1300 1200 310 10000 4500 280 9000 4000 1100 1000 8000 900 210 700 600 170 500 140 400 Torque [lb/in] 240 800 bar Drehmoment [Nm] 8 3500 7000 3000 6000 psi 1400 2 5 10 5000 2500 4000 2000 3000 300 100 200 70 100 0 0 50 100 150 200 250 300 350 400 1500 2000 1000 1000 35 450 500 0 0 50 100 150 200 250 300 350 400 450 Speed [Rpm] Drehzahl [1/min] TK 0400 US 50 70 90 110 114 130 0.5 1 2 4 15000 150 12000 240 10500 12 16 35 40 4000 3500 210 170 140 9000 3000 7500 2500 6000 2000 4500 100 150 200 250 300 350 100 3000 1500 70 1500 1000 0 35 400 0 50 100 150 200 250 300 350 500 400 Speed [Rpm] Drehzahl [1/min] Cont. 8 Flow [G/min] 20 24 28 30 32 13500 280 Torque [lb/in] 2 5 10 20 30 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 0 50 bar Drehmoment [Nm] Schluckstrom [L/min] psi Drehmoment [Nm] 1000 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 017 TK.indd, js 173 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série TK 0500 Schluckstrom [L/min] 5 10 20 30 50 70 110 114 90 130 12 4 150 2000 12 Flow [G/min] 20 24 16 US 28 30 32 35 40 15750 280 1600 4000 14000 3500 240 12250 1200 210 10500 3000 8750 2500 1000 Torque [lb/in] 1400 140 bar 170 800 600 7000 2000 5250 1500 100 400 3500 70 200 30 60 90 120 150 180 210 240 270 500 300 0 0 30 60 90 120 150 Speed [Rpm] Drehzahl [1/min] 180 210 240 270 TK 0630 US Flow [G/min] Schluckstrom [L/min] 5 10 20 30 50 70 90 110 114 130 150 225 1600 210 1400 1200 170 Torque [lb/in] 1800 1000 140 bar 800 600 100 400 70 200 35 0 0 25 50 75 100 125 150 175 200 225 250 12 4 8 16000 15000 14000 13000 12000 11000 10000 9000 8000 7000 6000 5000 4000 3000 2000 1000 0 0 25 12 16 20 25 30 32 40 3250 3000 2500 2000 1500 1000 500 50 75 100 125 150 175 200 225 250 Speed [Rpm] Drehzahl [1/min] TK 0800 5 10 20 30 psi 0 1000 1750 35 300 0 Drehmoment [Nm] psi 1800 Drehmoment [Nm] 8 17500 US 50 70 Schluckstrom [L/min] 90 110 130 150 170 Flow [G/min] 190 210 230 12 4 2400 8 12 16 20 24 28 32 35 40 45 50 55 60 20800 2200 18200 2000 15600 1600 1200 190 1000 170 3000 13000 2750 psi 210 Torque [lb/in] 1400 10400 bar Drehmoment [Nm] 1800 800 2500 7800 2000 140 600 5200 400 2600 200 0 0 25 50 75 100 125 150 175 200 225 250 275 100 70 300 0 0 Drehzahl [1/min] Cont. 1500 40 80 120 160 Speed [Rpm] 200 240 1000 500 280 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Caacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 017 TK.indd, js 174 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série TK 1000 US Schluckstrom [L/min] 5 10 20 30 50 70 90 110 130 150 170 190 210 Flow [G/min] 230 12 4 2800 8 12 16 20 24 28 32 35 40 45 50 55 60 24000 2600 2400 21000 18000 2000 1800 15000 190 170 1200 1000 800 2750 2500 12000 bar 1400 psi 1600 Torque [lb/in] Drehmoment [Nm] 2200 140 9000 2000 6000 600 1500 400 3000 100 200 0 0 20 Cont. 40 60 80 100 120 140 Drehzahl [1/min] 160 35 180 200 0 70 220 0 240 20 40 60 80 100 120 Speed [Rpm] 140 160 180 200 1000 500 220 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on testing using 10W40 oil with a viscosity of 200 SUS at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 10W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 10W40 d’une viscosite de 200 SUS a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 10W40 de 200 SUS de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 017 TK.indd, js 175 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série Flange Mount / Standardgehäuse Monture à bride(s) / Montaje de brida Wheel Mount / Radnabengehäuse Monture à roue / Montaje de rueda Side Load - N (lbs) Side Load - N (lbs) 71,171 (16,000) 71,171 (16,000) Max Load Curve 62,275 (14,000) Max Load Curve 62,275 (14,000) 53,378 (12,000) 53,378 (12,000) 44,482 (10,000) 44,482 (10,000) 35,584 (8,000) 35,584 (8,000) 26,688 (6,000) 26,688 (6,000) Dynamic Load Curve 17,792 (4,000) 17,792 (4,000) 8,896 (2,000) 8,896 (2,000) 0 0 -76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6 127.0 152.4 (-3) (-2) (-1) (0) (1) (2) (3) (4) (5) (6) Dynamic Load Curve -25.4 0 (-1) (0) Distance from Mounting Face - mm (in) Motor Image Not To Scale 25.4 50.8 76.2 101.6 127.0 152.4 177.8 203.2 (8) (1) (2) (3) (4) (5) (6) (7) Distance from Mounting Face - mm (in) Motor Image Not To Scale The dynamic side load curve is based on uni-directional steady state loads for L10 bearing life at 12 x 106 @ 100 RPM revolutions. Die zulaessige auslegbare radiale Wellenbelastungskurve ist unter ruhenden, einseitig statisch gerichteten Lastverhaltnissen auf eine L10 Lebensdauer mit 12 x 106 Umdrehungen kalkuliert bei 100 min. La courbe de charge laterale permise se base sur des charges unidirectionnelles en regime permanent pour le roulement L10 a 12 x 106 @ 100 RPM revolutions. La curva de valores admisibles de carga lateral esta basada en cargas contantes para cojinetes L10 a 12 x 106 revoluciones @ 100 RPM. The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads. Die maximale radiale Wellenbelastungskurve ist definiert als maximale statische Last ohne Drehzahl. Sie gilt als Grenze und sollte keinesfalls überschritten werden. La courbe de charge maximale est définie par la capacité de charge statique portante. Cette courbe ne devrait être dépassée en aucun moment y compris pour les charges par à-coups. La curva de carga máxima queda definida por la capacidad de carga estática del cojinete. No se deben superar los valores de esta curva, ni siquiera con cargas provisorias de impacto. Equation to Calculate the Expected Radial Bearing Life Gleichung zur Ermittlung der Lagerlebensdauer Equation to calculate the dynamic bearing life for a given load: Bestimmung der erlaubten radialen Wellenbelastung mit vorgegebener Last Use Fa, Fb and S in equation to determine hours of L10 bearing life. Die Lebensdauer in Stunden ergibt sich durch einsetzen von Fa, Fb und S in die nachstehende Formel. L = 12 x 106 60 x S { FF } 3.33 a b Where / Mit: S = Shaft Speed RPM / Abtriebswellendrehzahl in min -1 L = Life In Hours / Lebensdauer in Stunden Fa = Allowable side load defined by above curve at a distance from mounting flange. / Erlaubte radiale Wellenbelastung als Function der Laenge Fb = Application side load. / Anwendungsseitige Wellenbelastung Note: Calculations are based on L10 bearing life per ISO 281. Auslegung basiert auf einer L10 Lenbendauer nach ISO 281. 017 TK.indd, js 176 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série Code: K5 Standard SAE CC, 1 5/16-12 SAE Rear Radial "L" 22.8 (.900) 33.3 (1.31) 87.6 (3.45) ø150.9 (5.94) Max 51.94 (2.045) 45˚ A B 25.98 (1.023) 4 x 90˚ B 11.6 (.46) ø 14.35 (.565) 9/16 Thru Holes 150 (5.92) 1 5/16-12 STR THD O Ring Ports Code K5 disp. 0250 0315 0400 0500 0630 0800 1000 Weight/Gewicht kg 32.0 32.7 33.5 34.5 35.7 37.2 39.1 Poids/Peso (lb) (70.6) (72.0) (73.8) (76.0) (78.8) (82.1) (86.3) Length "L" mm "L" (in) ø 161.93 (6.375) A ø127.00 (5.000) 126.87 (4.995) 277 282 290 297 310 323 340 (10.9) (11.1) (11.4) (11.7) (12.2) (12.7) (13.4) Code: T5 Wheel Mount, 1 5/16-12 SAE Rear Radial "L" 99.05 (3.905) 22.8 (.900) 45˚ 96.45 (3.795) 33.3 (1.31) 87.6 (3.45) ø150.9 (5.94) Max 51.94 (2.045) A ø139.70 (5.500) 139.57 (5.495) B 25.98 (1.023) 1 5/16-12 STR THD O Ring Ports ø 184.15 (7.250) A 4 x 90˚ B 12.15 (.478) ø 14.35 (.565) 9/16 Thru Holes Code T5 disp. 0250 0315 0400 0500 0630 0800 1000 Weight/Gewicht kg 30.8 31.4 32.3 33.2 34.5 36.0 37.9 Poids/Peso (lb) Length (67.9) (69.3) (71.1) (73.3) (76.1) (79.4) (83.5) "L" mm 191 196 203 213 224 239 257 "L" (in) (7.5) (7.7) (8.0) (8.4) (8.8) (9.4) (10.1) 167 (6.57) English equivalents for metric specifications are shown in ( ). 017 TK.indd, js 177 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série Code K Code T Code: 32 1 1/2” Keyed 77.5 (3.05) 162.3 (6.39) 72.9 (2.87) 157.5 (6.20) 91.9 (3.62) 176.8 (6.96) 93.2 (3.67) 177.5 (6.99) Code: 36 1 1/2” 17 Tooth 12/24 Spline Code: 63 1 3/4” Tapered Code: 64 40mm Keyed English equivalents for metric specifications are shown in ( ). 017 TK.indd, js 178 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série 9.474 / 9.500 (.373 / .374) Code: 32 38.07 / 38.10 (1.499 / 1.500) 1 1/2” Keyed 41.83 (1.647) 60.3 (2.373) _ 3/8-16 UNC v18.54 (.730) Min. 37.41 / 38.1 (1.473 / 1.5000) Code: 36 1 1/2” 17 Tooth 12/24 Spline (.730) Min. 3.18 / 3.30 (.1250 / .1307) 35.4 (1.395) Min Full Spline Code: 63 1 3/4” Tapered 32.64 / 33.20 (1.285 / 1.307) _ 3/8-16 UNC v18.54 54 (2.125) 77.00 (3.030) 11.13 / 11.18 (.438 / .440) 5.49 (.216) 44.45 (1.750) Torque to Max. 610Nm (450 Ft Lb) See installation instructions 1.25-18 UNEF 1:8 Code: 64 40mm Keyed 73.66 (2.900) Min. 39.992 / 40.018 (1.5745 / 1.5755) M12 _ x 1.75 - 6H v1.00 Min. 11.79 / 11.91 (.464 / .469) 42.88 (1.688) English equivalents for metric specifications are shown in ( ). 017 TK.indd, js 179 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Notes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU TK Series / Serie / Série 017 TK.indd, js 180 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Large Frame Motors Posi-Trac Code: GAAA or GAAB US The Parker positive traction motor system “Posi-Trac” is designed for use on hydrostatic drive machines, with either open or closed hydraulic systems. This all hydraulic, Posi-Trac system allows for full differential effect until wheel slip occurs. The basic circuit utilizes two Parker TorqmotorsTM in series. Each of these motors contains a two position valve located in the motor’s end cover. These two Posi-Trac motors communicate with each other using two crossover hoses. Before wheel slip occurs, one motor provides the traction for the machine. Once wheel slip occurs, both wheels become the driving wheels and both have full traction capabilities. Posi-Trac smoothly engages without operator intervention. In the case where both wheels have very little traction, as with sand or loose gravel, the Posi-Trac power transmission alternates from side to side smoothly and quietly and drives the vehicle through the media. Posi-Trac is available in four wheel drive configurations, and Limited Slip variations also. Contact the factory for details. L + 27.7 mm (1.09 in) W + 2.04 kg (4.5 lb) Patented Hydraulic Circuit English equivalents for metric specifications are shown in ( ). 018 Large Frame Options.indd, js 181 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Speed Sensor / Drehzahl-Sensor Compte-tours / Contagiri Code: FSAA* or FSAB LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Large Frame Motors US An Economical Sensor for Speed Readout This rugged, weather resistant design is ideal for industrial and mobile applications. Applications include salt/sand/ fertilizer spreader drives, conveyer drives and injection molder compression drives. The sensor is a hall-effect type, which when externally powered outputs 30 square wave digital pulses per coupling shaft revolution. The connector is a user friendly universally available 4 pin polarized M12 connector allowing for simplified field service. The integrated design does not effect the side load capacity or performance of the torque motor. Dieser robuste, wetterfeste Drehzahlaufnehmer arbeitet nach dem Halleffekt. Es werden 30 Rechteckimpulse pro Abtriebswellenumdrehung erzeugt. Durch Erfassung der positiven und negativen Wellenflanken sind 60 Impulse pro Umdrehung möglich. Der Sensor führt zu keiner Leistungsbeschränkung des Motors. Die volle Radiallastkapazität bleibt erhalten. Un capteur economique pour mesure de la vitesse. Ce capteur robuste et resistant aux intemperies est a effet Hall. Alimente par une source externe, il fournit 30 ondes digitales carrees par tour. Par multiplication lelectronique on obient 60 pulsations par tour. Son montage ne modifie pas le couple ni la charge radiale du moteur qui le recoit. Este es un diseño de construcción reforzada, apto para uso a la intemperie e ideal para uso industrial y en equipos móviles. Entre sus aplicaciones, se puede mencionar esparcidores de sal, arena o fertilizantes, unidades motoras de transportadores y unidades motoras de compresión para moldeo a inyección. El sensor es del tipo de medio efecto, que al ser excitado externamente, genera 30 pulsos digitales de onda cuadrada por cada revolución del eje del acoplamiento. Utiliza un simple conector M12 polarizado tetrapolar, que es de uso común y facilita el mantenimiento en el lugar de instalación. El diseño integrado no afecta la capacidad de carga lateral ni la potencia del motor de torque. 65 (2.56) 69 (2.72) Maximum operating pressure 172 bar (2500 psi). English equivalents for metric specifications are shown in ( ). 018 Large Frame Options.indd, js 182 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Speed Sensor / Drehzahl-Sensor Compte-tours / Contagiri Operating voltage range Versorgungsspannung Gamme de tension de service Gama de voltaje de alimentacion Operating temperature Arbeitstemperatur Temperature de service Temperatura de servicio LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Large Frame Motors 4.5...24 VDC -20° to 220° F -29°...104° C Operating frequency range Arbeitsfrequenz Gamme de frequences de service Gama de frecuencia de servicio 0...10 KHZ Max sink current Erforderlicher Laststrom Courant d‘affaissement maxi Corriente maxima de alimentacion 0 ... 20 mA (max.) Connection Anschluß Branchement Conexion 4 Pin Polarized (12mm) Zubehör wie z.B. Kabel gehören 30 Pulses per revolution which can be doubled electronically 30 impulsions par revolution pouvant etre doublees electroniquement 30 pulsos por revlucion, que pueden duplicarse electronicamente nicht zum Lieferumfang. Sensor output Sonsorausgang Sortie du détecteur Salida del sensor Output is NPN Ausgang is NPN La sortie est NPN La salida es NPN Open Collector Collecteur ouvert Colector abierto El cable y la resistencia de arranque no se suministran originalmente de fábrica. 4 Pin Polarized M12 Connector (Male) Cable and “Pull Up” Resistor are not supplied by factory. Le câble et la résistance “Pull Up” ne sont pas fournis par l’usine. "Pull Up" Resistor SENSOR PIN # 1 (+) 4.5 to 24 VDC PIN # 4 OUTPUT PIN # 3 (_) PIN # 2 NO CONNECTION Pull-up Resistor Value Formula Formel zur Ermittlung des (0.25 Watt, 5% de tol.) Pull up-Widerstandes (0.25 Watt, Tol. 5%) Formule de la valeur de resistance “Pull-up“ (0.25 Watt 5% Tol.) Calculo de la resisancia de carga (0.25 Watt, toll. 5%) Voltage / Spannung Curant d‘affaisement / Voltaje 4.5...24 VDC Sink Current / Laststrom Resistance / Corriente de ali mentacion Status: Offstate / aus Etat: Arret / Estado Inactivo (95% +V) +V 0...20 mA = Resistor Widerstand (k Ohm) Resistance Resistancia Status: Onstate / ein Etat: Marche / Estado Activo (max. 0.4 VDC) 0V 018 Large Frame Options.indd, js 183 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Hot Oil Shuttle Valve / Spülventil Valve de rincage / Valvola scambiatrice Code: AAFX or AAAT* LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Large Frame Motors US A Hot Oil Shuttle is used to continuously remove a portion of the fluid in a closed loop transmission or other closed loop system. At 125 PSI pressure differential between the motor return port and the shuttle outlet,1.5 GPM* will exit the circuit to cool, filter and return to the reservoir. The constant loop replenishment helps to keep heat and contamination from building up in the circuit. This option is not available with rear ports or integral cross over relief. Spülventil für geschlossene Systeme zur Rückführung einer definierten Menge des Niederdrucköls in den Tank zur Abkühlung innerhalb desselben Kreislaufs. Valve de rincage pour systèmes fermès pour le retour d`un volume dèterminè de fluide basse pression vers le rèservoir, un refroidisseur ou un filtre de rèfrigèration, dans le même circuit. Un transferidor de aceite caliente actúa permanentemente para extraer una parte del fluido en una transmisión de circuito cerrado u otro sistema de circuito cerrado. Entre la entrada de retorno del motor y la salida del transferidor hay una diferencia de presión de 125 psi (libras/pulg.2), y a esta presión salen 1,5 galones por minuto del circuito para enfriarse, filtrarse y volver al depósito de fluido. El reacondicionamiento permanente de parte del fluido evita la contaminación del mismo y el incremento de temperatura en el circuito. A 25˚43´ B 18 (.71) 9/16-18UNF, O-Ring "L" + 19.8 (.78) "W" + 1.4 kg (3.1 lb) A B Q=5 l p=9 bar ϑ=39 cSt (Q=1.32 gal) (p=131 psi) (ϑ=190 SUS) Standard Length & Weights for TF Series on Pages 84-85, TG Series on Pages 120-121 and TH Series on Pages 150-151. Längen/Gewichte TF Serie Seiten 84-85, TG Serie Seiten 120-121, TH Serie Seiten 150-151. Longueurs et poids courants pour la série TF, voir les pages 84-85, et la série TG, voir les pages 120-121, et la série TH, voir les pages 150-151. Los valores estándar de longitud y peso de la Serie TF se puede ver en las Páginas 84-85, y de la Serie TG en las Páginas 120-121, y de la Serie TH en las Páginas 150-151. English equivalents for metric specifications are shown in ( ). 018 Large Frame Options.indd, js 184 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Internal relief valve / Schockventil intern Soupape de sécurité interne / Regolatrice di pressione interna LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Large Frame Motors Code: BBBA*, BBBB*, BBBC*, BBBD* or BBBG* US This integrated internal relief valve is used for fixed pressure settings. Internes Schockventil La soupape de sécurité interne utilise pour des valeurs de pression fixes. La valvula interna de alivio se utiliza para cablibraciones fijas de presion. A B "L" + 27.7 (1.09) "W" + 2.04 kg (4.5 lb) A B Bestellschlüssel / Systéme de Commande / Ordering system / Informacion para pedidos Pressure bar (psi) Option * 69 (1000) A * * B Öffnungsdruck Opening pressure Tarage Presion de apertura 138 (2000) 207 (3000) * 276 (4000) * 103 (1500) Standard Length & Weights for TF Series on Pages 84-85, TG Series on Pages 109-111 and TH Series on Pages 139-140. Längen/Gewichte TF Serie Seiten 84-85, TG Serie Seiten 109-111, TH Serie Seiten 139-140. Longueurs et poids courants pour la série TF, voir les pages 84-85, et la série TG, voir les pages 109-111, et la série TH, voir les pages 139-140. Los valores estándar de longitud y peso de la Serie TF se puede ver en las Páginas 84-85, y de la Serie TG en las Páginas 109-111, y de la Serie TH en las Páginas 139-140. English equivalents for metric specifications are shown in ( ). 018 Large Frame Options.indd, js 185 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Large Frame Motors Standard Options Code: AAAC US Code: AAAC Double Paint — Base coat of red oxide primer and finish Zweischichtlackierung schwarz coat of black paint for increased corrosion resistance. Code AAAF* or AABP Code: AAAF* or AABP US Code: AAAJ* or AAFG US Kronenmutter Castle Nut — All motors ordered with Tapered shafts are S e l b s t s i c h e r n d e M u t t e r w i r d e r s e t z t d u r c h equipped with patch locking nuts. If desired, a castle nut Kronenmutter may be specified. Code: AAAJ* or AAFG Vespel™ Commutator Seal — Under conditions of high Vespel™ / Kommutator Dichtung Für Anwendungen im höheren Temperaturbereich oder temperature, it is suggested that a vespel commutator seal be used. nicht ausreichender Schmierung. Code: AAAG* or AAAH US Code: AAAG* or AAAH Fluorocarbon — is available under various registered trademarks, including VITON™ (a registered trademark of DuPont), FLUOREL™ (a registered trademark of 3M) or FPM™ (a registered trademark of DuPont). Code: AABJ* or AABK US Fluorocarbon Dichtungen Für Anwendungen im höheren/niedrigeren Tenperaturenbereich oder speziellen Flüssigkeiten wird der Einsatz von Fluorcarbon Dichtungen empfohlen. Fluorocarbon ist bekannt unter verschiedenen eingetragenen Warenzeichen VITON™ - DuPont, Fluorel™ - 3M, FPM™ - DuPont Free Running Rotorset — The “free running rotorset” is a specially dimensioned rotorset that allows for smoother Code: AABJ* or AABK operation at low flows and low pressure. Volumetric efficiency can be affected. Leichtläufer Rotorsatz Anlaufdruck < 5 bar Code: AANM* US Code: AANM* Seal Saver — Seal saver is a metal disc that presses onto the motor shaft, covering the dirt and water (D&W) seal. It’s purpose is to aid in preventing external contamination from damaging the D&W seal. Versiegelungsschutz — Der Versiegelungsschutz besteht aus einer Metallscheibe, die gegen die Antriebswelle druckt und damit Schmutz- und Wasserdichtung (D&W-Dichtung) abdeckt. Hierdurch soll einer Beschadigung der D&W-Dichtung auf Grund externer Verunreinigungen vorgebeugt werden. For more standard options see page 187 * Option code shown is with a single black coat of paint. * Motor schwarz grundiert 018 Large Frame Options.indd, js 186 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Large Frame Motors Standard Options Availability TF/DF Clutch TG/DG Code TH BG/BH TK TL Painted Unpainted US AAWM Description AAWL Fluorocarbon shaft seal. US US US US US AAAC - US US US US US AAAF AABP Castle Nut / Kronenmutter US US US US AAAG AAAH Fluorocarbon Seals / Fluorocarbon Dichtungen US US US US US AAAJ AAFG Vespel™ Commutator Seal / Vespel™ Kommutator Dichtung US US US US AABJ* AABK* Free Running Rotorset / Leichtläufer-Rotorsatz US US US US AAAT** AAFX** Hot Oil Shuttle (11:00) / Spülventil US US US US US US AANM Double Paint / Zweischichten – Lackierung - Seal saver for 1.25 taper shaft only - 678 Nm (6000 in-lb) Holding Capacity US AANB US AAMN AANH 1808 Nm (16000 in-lb) Holding Capacity FSAA FSAB US US US US US US US BBBA** BBBM** 69 Bar (1000 PSI) Internal Bidirectional Relief / Internes Schockventil US US US US BBBG** BBBJ** 103 Bar (1500 PSI) nternal Bidirectional Relief / Internes Schockventil BBBB** BBBN** 138 Bar (2000 PSI) Internal Bidirectional Relief / Internes Schockventil US US US US US US US US US US US US US Speed Sensor / Drehzahl-Sensor BBBC** BBBF** 207 Bar (3000 PSI) Internal Bidirectional Relief / Internes Schockventil BBBD** BBBW** 276 Bar (4000 PSI) Internal Bidirectional Relief / Internes Schockventil Consult factory for other positions and combinations. * Not applicable to TF, TG or TH 0625, 0785 or 0960 displacement codes. ** Not available with A, B, E, Y, X or L porting. If specifying internal bidirectional reliefs, relief settings cannot exceed intermittent pressure rating of motor. 018 Large Frame Options.indd, js 187 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Installation/Operation Information LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Torqmotors™ Fluid Other Operating Conditions To insure maximum motor performance and life, use a premium grade hydralic or engine oil. Fluids with a minimum of .125% zinc (or equivalent) anti-wear package should be used. A mineral or synthetic based 10W40 engine oil or hydraulic (200 SUS) is recommended. TorqmotorTM seals come standard in nitrile rubber. If a fluid that is not compatible with nitrile is to be used, a fluoroelastomer seal material can be specified. • Minimum fluid viscosity is 50 SUS • Recommended fluid operating temperature is -28° C to 93° C (-20°F to 200° F) • Filtration level is 20-50 micron nominal Consult factory before operating at conditions exceeding any ratings or recommendations in this catalog. Installation Recommendations • To avoid contamination do not remove plastic port plugs until fittings are to be installed. • Motor mounting flange must make full contact with equipment mount; do not use the mounting bolts to force the motor pilot into the pilot hole to align the motor. • Pulleys, sprockets, wheels, or couplings should be properly aligned on the shaft to avoid excessive radial or thrust loads. • To avoid damaging the thrust system, do not hammer on the motor or shaft to install or remove couplings, pulleys, sprockets, etc. Pressure Operating the motor in its intermittent pressure range will shorten the life of the motor and should generally be restricted to 10% or less per minute. The reduced life resulting from continuous operation in the intermittent range may be acceptable in some applications. Consult the factory for details. Tapered Shaft The tightening torque listed for a taper shaft nut is based on strength of the shaft and nut. Hub design and hub material determine the application tightening torque. Refer to hub manufacturers specifications to determine actual assembly torque. Factory suggested assembly torques are: 250-400 lb-ft (1.25, 1.5 & 1.75 Dia. Shafts), 175-225 lb-ft (1.0 dia. shafts). Shaft Loading The use of 1 inch and 25mm diameter shafts are not recommended when torque loads exceed 3500 lb-in. 316 stainless shafts should be limited to 2000 lb-in. For 7/8 inch diameter shafts, torque should be limited to 2500 lb-in. Corrosion resistant Nitrotec shafts have reduced torque-carrying capability. Consult factory for values for specific shafts. The maximum thrust load on all shafts should not exceed 1000 lbs inward or outward. To insure a sound hub to shaft coupling, the hub must conform to the full length of the shaft taper. This will prevent bending stresses at the keyway that could cause a fatigue failure. Performance Data Castle Nut Performance data shown in this catalog is the result of testing performed using 10W40 oil at 54oC (130oF), 200 SUS. Actual performance will vary with fluid conditions. Lower viscosity will produce lower performance. All motors ordered with Tapered shafts are equipped with patch locking nuts. If desired, a castle nut may be specified. Paint Inlet Conditions Unless specified otherwise, motors are shipped unpainted and coated with a rust inhibitor. Paint options are: * Single coat of black paint. * Single coat of black paint plus a coat of red oxide primer. (Double paint). Positive pressure must be available at the motor inlet while it is rotating. If an overrunning load causes the motor to rotate faster than the pump can fill it, cavitation will occur. Consult the factory for inlet pressure requirements and speed limitations. 019 Installation-Operation.indd, js 188 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Shaft Rotation Installation/Operation Information Reverse Timed Manifold All motors in this catalog are bi-rotational. The efficiency of the motors is essentially unaffected by direction of rotation. The direction of output shaft rotation depicted below is that which will result from pressurizing the “A” port of the motor. Pressurizing the “B” port will cause shaft rotation in the opposite direction. Direction of rotation is as seen by looking directly at the shaft. “Front ported” motors have the ports at the shaft end of the motor. “Rear ported” motors have the ports in the end cap of the motor. Standard motors are Rotation Code “0”. Reverse timed motors are Rotation Code “1”. Series TC, TB, TE, TJ TF, DF, TG, BG, DG, TH, BH TK 110A 700, 716 Standard Code “0” Reverse Timed Code “1” Front Ported Rear Ported Front Ported Rear Ported CW CCW CCW CW CCW CW CW CCW N/A CW N/A CCW CW N/A N/A N/A CCW N/A N/A N/A 019 Installation-Operation.indd, js 189 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Installation/Operation Information LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Brake Motors Brake release pressure: CAUTION! The brake release port is designed for 3000 psi maximum. Limiting the pressure in that port to below 1500 psi is recommended to enhance seal life. Static Brake Only: The brakes on these motors are designed for static use only, i.e., the brake should not be used to stop the motor and the motor should not be stared while the brake is applied. These brakes are "parking" brakes only. Using the brake in a dynamic condition (while the motor is turning) will damage and reduce the holding capacity of the brake. If the brake does not hold because it has been damaged, personal injury or property damage could result. Initial use, bleeding not required: Bleeding the brake is not required. It is recommended that the brake release port be filled with approximately 1.2 oz. (36cc) system oil prior to installation or first use. Torque for mounting bolts: Brake holding capacity and periodic test: Customer installed mounting bolts should be grade 8 and torqued to a minimum of 90 ft-lbs. The brake holding capacity rating is based on actual holding capacity when new. If properly used as a static brake only, the holding capacity will slowly decrease with time. Since holding capacity will slowly decrease over time, a proper maintenance procedure should include periodically testing the holding capacity of the brake. This can be achieved by running a vehicle ramp test per OEM instructions. Brake service intervals: The seals, springs and brake disc package should be periodically (how often depends on your application) inspected and replaced if damaged or worn. All should be replaced at least every 250,000 brake cycles or 3 years, whichever occurs first. Brake orientation: This wet sump, multi-disk brake is designed to be mounted with the shaft in a horizontal position. If your application will have the motor in any other orientation, the motor should be thoroughly tested for longevity of brake holding capacity. This can be achieved by running a vehicle ramp test per OEM instructions after a predetermined number of brake actuations. Under no circumstances, however, should the motor be mounted with the shaft pointing vertically upward because the disks will not be operating within the oil sump and damage to the brake disks will occur. 019 Installation-Operation.indd, js 190 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 019 Installation-Operation.indd, js 191 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni / Informacion Tecnica (3.6 – 24.1 in3/rev) 59…395 cm3/rev 9 Displacements 9 Schluckvolumen 9 Cylindrée 9 Despazamientos Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Cont (to 2500 psi) …172.4 bar Maximum Oil Flow Schluckstrom Débit d’huile Caudal Maximo de Aceite Maximum Speed Drehzahl Vitesse de rotation Velocidad Maxima Maximum Torque Max Drehmoment Couple Torque Maximo Int (to 3000 psi) …206.8 bar LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU When the Ultimate in Efficiency and Reliability is a Must This high performance motor contains a power element that is pressure loaded against internal leakage for high volumetric efficiency. It is wear compensated, so that its volumetric efficiency will not degrade with use. It can provide up to 5215 lb-in of torque through a one-piece solid fixed axis shaft. This shaft design allows for full stationary spline contact between shaft and rotor, minimizing spline contact stresses. It also allows the shaft to be extended through the rear cover for mounting parking brakes, auxiliary drive functions or encoders for speed readout or closed loop control. Low internal pressure drop means high mechanical efficiency and higher flow capability. This rugged motor is the most compact on the market. (to 30 gpm) …113.6 lpm 858 rpm Cont Int (to 4164 lb in) (to 5215 lb in) …470 Nm …589 Nm Maximum Side Load at Key Seitenlast Charges latèrales Carga Maxima Lateral (to 1450 lb) … 6450 N 020 110A.indd, js 192 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l Cil ndré luck acem ind e vo lum ent ra t a en Ma x. s Ma pe e x Vit . Dre d @ es hz Ma Ve se d ahl x. i n loc In e ida rot term term a i d t Ma ma ion ittie tten x xim ma ren t flo Ma . oil de a a xi flo x rB w ca Dé . Sch w etr ud bit ie b luc al : Po d´h ks i n t t r ta e r u rm ta ile m om i t m e Ma nte ax axi x ma Ma . diff x im er x o Ch . Dru enti ute ck al p ge r Pr d e e s e p f ä ll s s u ion re e re dif ssio Ma e re n m x. nc Ma sup ia l a x i x. ply ma E Pr p i n xim r es ga e a Pr sion ngs ssur es e d ion max ruc ma i en k Ma x im t ré x ad e Ma . torq ea x u lim Co . Dre e en up hm tac To le m om ion rqu e a nt e M xi ax Ma im x o Ma . per for x. Pu Lei ma st nc is Ma sanc unga e xim e d bg o r e s abe en ort dim ie en max to i LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU Motor Series 110A cm3/rev in3/rev rev/min cont / int* l/min g/min cont / int* bar psi max bar psi cont / int* Nm lb-in max KW HP 110A 036 59 3.6 858 45.4 12 53 14 170 2500 210 3000 225 3250 127 1125 149 1319 8.5 11.4 110A 054 89 5.4 740 60.6 16 68.1 18 170 2500 210 3000 225 3250 182 1608 213 1884 11.2 15.1 110A 071 116 7.1 684 75.7 20 83.3 22 170 2500 210 3000 225 3250 256 2267 308 2725 14.2 19.1 110A 088 144 8.8 622 75.7 20 94.6 25 170 2500 210 3000 225 3250 324 2874 389 3449 14.6 19.6 110A 106 174 10.6 519 75.7 20 94.5 25 155 2250 210 3000 225 3250 352 3115 465 4121 13.1 17.6 110A 129 211 12.9 437 75.7 20 94.6 25 155 2250 190 2750 225 3250 412 3651 503 4453 12.9 17.3 110A 164 269 16.4 415 75.7 20 114 30 140 2000 170 2500 225 3250 470 4164 589 5215 12.1 16.2 110A 189 310 18.9 350 75.7 20 114 30 140 2000 170 2500 225 3250 542 4803 675 5977 7.9 10.6 110A 241 395 24.1 279 75.7 20 114 30 120 1750 155 2250 225 3250 594 5261 764 6765 9.2 12.4 Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. * Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 020 110A.indd, js 193 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos 11 X A Series Shaft Welle Arbre Ejes XXX X LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU X X X Thru-Shaft Engineering Mounting durchgehende Welle Design Gehäuse arbre traversant technischer Carter Eje pasante Entwurf Montaje Conception technique Ports Diseño de Anschluß ingeniería Displacement Plan de raccordement Schluckvolumen Lumbreras Cylindrée Desplazamiento X X Cross-Over Shaft Material Relief Valve Wellenmaterial Matériel d'arbre Bremslüftventil Soupape de Material del eje sûreté transversale Válvula de Paint alivio transversal Code 1" Keyed Code SAE A 2-Bolt, Manifold 0 1" 6B Spline 1 25mm Keyed 2 1-1/4" Keyed 3 Code cm³/U cm³/tr cm³/giro cu in³/rev 036 59 / 3.6 054 89 / 5.4 071 116 / 7.1 8.8 088 144 / 106 174 / 10.6 129 211 / 12.9 164 269 / 16.4 189 310 / 18.9 241 395 / 24.1 AM SAE A 2-Bolt, 7/8”-14 SAE AS SAE A 2-Bolt, 1/2”-BSPP AP SAE B 2-Bolt, Manifold BM 1-1/4"-14 Tooth Spline SAE B 2-Bolt, 7/8”-14 SAE 5 BS 7/8"-13 Tooth Spline 6 Code 0 1 E No Thru Shaft Thru Shaft Endcoder Code Omit S Code Omit R1 If Not Required Stainless Steel If Not Required Cross-Over Relief Valve Code Omit F Consult factory for other available options, configurations ordering codes and lead times. No Paint Black Paint Schwarz lackiert 020 110A.indd, js 194 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU 110A 036 23 15 30 38 Flow [G/min] 2 53 45 200 1750 175 1500 210 125 100 Torque [lb/in] 170 140 75 100 bar Drehmoment [Nm] 150 6 4 8 10 12 US 14 1250 3000 1000 2500 2000 750 psi Schluckstrom [L/min] 8 1500 500 50 70 1000 250 25 35 500 0 0 100 200 300 400 500 600 700 800 0 900 0 100 200 300 400 Drehzahl [1/min] 500 600 700 800 900 1000 Speed [Rpm] 110A 054 Schluckstrom [L/min] 8 15 30 23 38 45 53 61 2 68 4 6 8 2250 300 275 Flow [G/min] 12 10 US 14 16 18 2000 1750 3000 200 1500 Torque [lb/in] 210 175 170 150 140 125 100 bar Drehmoment [Nm] 225 100 75 2000 1000 1500 750 1000 500 70 50 2500 1250 psi 250 250 25 35 500 0 0 100 200 300 400 500 600 700 0 800 0 100 200 300 400 500 600 700 800 Speed [Rpm] Drehzahl [1/min] 110A 071 Schluckstrom [L/min] 8 15 23 30 38 45 53 61 68 76 2 83 4 6 8 10 Flow [G/min] 14 12 16 18 20 22 US 3500 400 3250 3000 350 2750 2500 170 200 140 2000 2500 1750 2000 1500 1250 1500 1000 100 100 750 70 1000 500 50 250 35 0 0 0 Cont. with no side load Int. with rated side load 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 Speed [Rpm] Drehzahl [1/min] Cont. 500 0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 020 110A.indd, js 195 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA psi Torque [lb/in] 250 150 3000 2250 210 bar Drehmoment [Nm] 300 Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU 110A 088 Schluckstrom [L/min] 2 8 15 30 23 45 38 53 61 76 68 83 4 6 8 10 12 Flow [G/min] 14 16 18 US 20 25 22 4000 95 3500 400 3000 350 2500 210 Torque [lb/in] 300 170 250 3000 2500 2000 2000 200 140 150 100 1000 70 500 1500 1500 100 1000 50 35 0 0 100 200 300 400 500 600 psi 450 bar Drehmoment [Nm] 500 500 700 0 0 700 100 200 300 400 500 600 Speed [Rpm] Drehzahl [1/min] 110A 106 Schluckstrom [L/min] 15 23 8 500 38 30 53 45 61 68 Flow [G/min] 83 76 95 5000 4 6 8 10 12 14 16 18 US 22 20 25 4500 450 4000 400 210 3500 190 300 Torque [lb/in] 170 155 250 140 200 120 150 100 100 3000 2750 3000 2500 2500 2250 2000 2000 psi 350 bar Drehmoment [Nm] 2 1750 1500 1500 1000 70 1000 50 500 35 0 0 100 200 300 400 500 500 600 0 600 0 100 200 300 400 500 Speed [Rpm] Drehzahl [1/min] 110A 129 Schluckstrom [L/min] 8 15 23 30 38 45 53 61 68 83 76 5000 95 2 4 6 8 10 12 Flow [G/min] 14 16 18 US 20 22 25 550 4500 500 4000 2750 190 350 300 140 250 120 200 100 Torque [lb/in] 3500 170 155 2000 2500 1750 2000 1500 1500 150 100 1000 70 50 50 100 150 200 250 300 350 400 450 500 0 500 0 Drehzahl [1/min] Cont. Cont. with no side load Int. with rated side load 1000 500 35 0 0 2500 2250 3000 psi 400 bar Drehmoment [Nm] 450 50 100 150 200 250 Speed [Rpm] 300 350 400 450 500 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 020 110A.indd, js 196 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU 110A 164 Schluckstrom [L/min] 8 15 23 30 38 45 53 61 68 83 76 95 700 4 6 10 12 8 Flow [G/min] 14 16 18 20 22 25 US 30 5500 650 5000 550 4500 170 450 155 400 140 350 bar 120 300 100 250 200 150 2500 4000 Torque [lb/in] 500 2250 3500 2000 3000 1750 2500 1500 2000 1500 70 100 psi 600 Drehmoment [Nm] 2 6000 114 1000 1000 50 35 0 0 50 100 150 200 250 300 350 400 500 500 450 0 0 50 100 150 Drehzahl [1/min] 200 250 Speed [Rpm] 300 350 400 450 110A 189 Schluckstrom [L/min] 15 23 30 38 53 61 45 68 76 Flow [G/min] 83 95 114 2 4 6 8 10 12 14 16 18 US 20 22 25 30 7000 800 750 700 650 600 550 500 450 400 350 300 250 200 150 100 50 0 6500 6000 5500 5000 170 155 140 120 100 0 50 100 150 200 250 300 350 85 70 400 4000 psi Torque [lb/in] 4500 bar Drehmoment [Nm] 8 3500 3000 2500 2500 2250 2000 1500 2000 1750 1000 1500 1250 500 1000 400 0 0 Drehzahl [1/min] 50 100 150 200 Speed [Rpm] 250 300 350 110A 241 Schluckstrom [L/min] 23 30 38 45 53 61 68 Flow [G/min] 76 83 95 114 7500 2 4 6 8 10 12 14 16 18 US 20 22 25 30 7000 6500 6000 5500 155 2250 5000 120 100 85 70 4500 2000 4000 1750 psi 140 Torque [lb/in] 850 800 750 700 650 600 550 500 450 400 350 300 250 200 150 100 50 0 0 15 bar Drehmoment [Nm] 8 3500 1500 3000 2500 1250 2000 1000 1500 1000 500 35 25 50 75 100 125 150 175 200 225 250 275 0 Drehzahl [1/min] Cont. Cont. with no side load Int. with rated side load 500 0 300 25 50 75 100 125 150 175 Speed [Rpm] 200 225 250 275 300 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 020 110A.indd, js 197 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU Radial Load - N (lb) 13345 (3000) 11121 (2500) 8896 (2000) 6672 (1500) Torque nm (lb-in) 0 112.9 (1000) 4448 (1000) 225.9 (2000) 338.9 (3000) 451.9 (4000) 2224 (500) 0 -50.8 (-2) 519.7 (5000) -25.4 (-1) 0 (0) 25.4 (1) 50.8 (2) 76.2 (3) Distance From Mounting Face - mm (in) The allowable side load curve is based on L10 bushing life of 3 x 106 revolutions @ 100 RPM. Die zulassige radiale Wellenbelastung bezieht sich auf die Lager-Lebensdauer 3 x 106 Umdrehungen. L’effort radial admissible sur l’arbre depend a une duree de vie 3 x 106 de rotation. La curva de carga lateral admisible se basa en vida util de cojinete de 3 x 10 revoluciones. 020 110A.indd, js 198 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras Code: AM LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU "L" 28.5 (1.12) SAE A 2-Bolt, Manifold 15.7 (.62) 2X 14.2 (.56) 11.2 (.44) 3.1 (.12) 2 x 14.2 (.56) 2x 31.8 (1.25) A 22.99 (.905) Ø 114.3 (4.50) 130.3 (5.13) Max A Ø 82.55 (3.250) B 106.4 (4.188) B 22.99 (.905) 2 X 31.88 (1.255) 7/16-20 STRAIGHT THD O-RING CASE DRAIN 2x 22.9 (.90) 59.9 (2.36) 58.5 (2.305) For Manifold 4x 5/16-18 UNC-2B x 12.7 (.50) Min Full Thread ø 20.62 (.812) x 2.03 (.080) Deep O-rings Motor with manifold mount is supplied with 2 O-rings. 2.03 (0.80) 117.1(4.61) 115.6 (4.55) For Manifold Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. 20.62 (0.812) Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni é corredato da 2 OR. Code AM Weight/Gewicht kg Poids/Peso (lb) Length "L" mm "L" (in) 036 7.0 (15.4) 112 (4.41) 054 7.4 (16.2) 117 (4.60) 071 7.7 (16.9) 121 (4.78) 088 8.0 (17.5) 127 (4.98) 106 8.4 (18.4) 131 (5.17) 129 8.7 (19.1) 138 (5.42) 164 9.4 (20.6) 147 (5.80) 189 9.8 (21.6) 154 (6.07) 241 10.8 ( 23.7) 169 (6.64) Code: AS "L" SAE A 2-Bolt, 7/8“-14 SAE O-Ring 28.5 (1.12) 15.7 (.62) 2X 14.2 (.56) 11.2 (.44) 3.1 (.12) 22.99 (.905) 2 x 25.4 (1.00) A Ø 82.55 (3.250) Ø 114.3 (4.50) 106.4 (4.188) B B 22.99 (.905) 2 X 31.88 (1.255) 7/16-20 STRAIGHT THD O-RING CASE DRAIN 130.3 (5.13) Max A 59.9 (2.36) 58.5 (2.305) For Manifold 7/8-14 SAE O-Ring 117.1(4.61) 115.6 (4.55) For Manifold Code AS Weight/Gewicht kg Poids/Peso (lb) Length "L" mm "L" (in) 036 7.0 (15.4) 112 (4.41) 054 7.4 (16.2) 117 (4.60) 071 7.7 (16.9) 121 (4.78) 088 8.0 (17.5) 127 (4.98) 106 8.4 (18.4) 131 (5.17) 129 8.7 (19.1) 138 (5.42) 164 9.4 (20.6) 147 (5.80) 189 9.8 (21.6) 154 (6.07) 241 10.8 (23.7) 169 (6.64) English equivalents for metric specifications are shown in ( ). 020 110A.indd, js 199 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU Code: AP "L" SAE A 2-Bolt, 1/2“ BSPP 28.5 (1.12) 15.7 (.62) 2X 14.2 (.56) 11.2 (.44) 3.1 (.12) 22.99 (.905) 2 x 25.4 (1.00) A Ø 114.3 (4.50) 130.3 (5.13) Max A Ø 82.55 (3.250) 106.4 (4.188) B B 22.99 (.905) 2 X 31.88 (1.255) 7/16-20 STRAIGHT THD O-RING CASE DRAIN 59.9 (2.36) 58.5 (2.305) For Manifold 1/2 BSPP 117.1(4.61) 115.6 (4.55) For Manifold Code AT Weight/Gewicht kg Poids/Peso (lb) Length "L" mm "L" (in) 036 7.0 (15.4) 112 (4.41) Code: BM 054 7.4 (16.2) 117 (4.60) 071 7.7 (16.9) 121 (4.78) 088 8.0 (17.5) 127 (4.98) 106 8.4 (18.4) 131 (5.17) 129 8.7 (19.1) 138 (5.42) 164 9.4 (20.6) 147 (5.80) 189 9.8 (21.6) 154 (6.07) 241 10.8 ( 23.7) 169 (6.64) "L" 29.2 (1.15) SAE B 2-Bolt, Manifold 14.0 (.55) 2X 14.2 (.56) 6.4 (.25) 15.7 (.62) 2 x 14.2 (.56) 22.99 (.905) 2x 31.8 (1.25) Ø 101.57 (3.999) A Ø 114.3 (4.50) 176.0 (6.93) Max A 143.8 (5.66) B B 2 X 31.88 (1.255) 7/16-20 STRAIGHT THD O-RING CASE DRAIN 22.99 (.905) 2x 22.9 (.90) 4x 5/16-18 UNC-2B x 12.7 (.50) Min Full Thread ø 20.62 (.812) x 2.03 (.080) Deep Motor with manifold mount is supplied with 2 O-rings. O-rings 60.2 (2.37) 58.55 (2.305) For Manifold 2.03 (0.80) Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni é corredato da 2 OR. Code BM 036 054 071 088 106 129 164 189 241 kg (lb) 7.0 (15.4) 7.4 (16.2) 7.7 (16.9) 8.0 (17.5) 8.4 (18.4) 8.7 (19.1) 9.4 (20.6) 9.8 (21.6) 10.8 (23.7) "L" mm "L" (in) 112 (4.41) 117 (4.60) 121 (4.78) 127 (4.98) 131 (5.17) 138 (5.42) 147 (5.80) 154 (6.07) 169 (6.64) Weight/Gewicht Poids/Peso Length 120.7 (4.75) 118.75 (4.675) For Manifold 20.62 (0.812) English equivalents for metric specifications are shown in ( ). 020 110A.indd, js 200 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras Code: BS LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU "L" 29.2 (1.15) SAE B 2-Bolt, 7/8“-14 SAE O-Ring 14.0 (.55) 2X 14.2 (.56) 6.4 (.25) 15.7 (.62) 22.99 (.905) 2x 25.4 (1.00) Ø 101.57 (3.999) A Ø 114.3 (4.50) A 143.8 (5.66) B B 2 X 31.88 (1.255) 7/16-20 STRAIGHT THD O-RING CASE DRAIN 176.0 (6.93) Max 22.99 (.905) 7/8-14 SAE O-Ring Motor with manifold mount is supplied with 2 O-rings. O-rings 60.2 (2.37) 58.55 (2.305) For Manifold 2.03 (0.80) Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni é corredato da 2 OR. Code BS Weight/Gewicht kg Poids/Peso (lb) Length "L" mm "L" (in) 036 7.0 (15.4) 112 (4.41) 054 7.4 (16.2) 117 (4.60) 071 7.7 (16.9) 121 (4.78) 120.7 (4.75) 118.75 (4.675) For Manifold 20.62 (0.812) 088 8.0 (17.5) 127 (4.98) 106 8.4 (18.4) 131 (5.17) 129 8.7 (19.1) 138 (5.42) 164 9.4 (20.6) 147 (5.80) 189 9.8 (21.6) 154 (6.07) 241 10.8 ( 23.7) 169 (6.64) English equivalents for metric specifications are shown in ( ). 020 110A.indd, js 201 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU Code A Code B Code: 0 1” Keyed 45.5 (1.79) Code: 1 1” 6B Spline 45.5 (1.79) Code: 2 25mm Keyed 54.6 (2.15) Code: 3 1-1/4” Keyed 53.8 (2.12) English equivalents for metric specifications are shown in ( ). 020 110A.indd, js 202 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU 18.6 (.73) Code: 0 Key 1/4 x 1 Woodruff #15 Per SAE J502 6.37 (.251) 1” Keyed 28.4 (1.120) ø 25.37 (.999) 1/4-20 UNC thd x 15.75 (.62) Min Deep Code: 1 1” 6B Spline 25.4 (1.00) Min Full Spline SAE 6B ø 25.30 (.996) ø 25.27 (.995) 1/4-20 UNC thd x 15.75 (.62) Min Deep 41.38 (1.629) 37.39 (1.472) Code: 2 25.000 (.9843) 25mm Keyed .315 .314 (8mm) M8x1.25H-6H x16.0(.63) Min Deep 20.9 (.826) Key A8x7x32mm Code: 3 47.8 (1.88) 39.4 (1.55) x 7.95 (.313) 1-1/4” Keyed ø 31.737 (1.2495) 7.96 (.3135) 34.9 (1.373) 3/8-16 UNC thd x 19.05 (.75) Min Deep Key 7.950 x 31.5 (.3130 x 1.24) Square English equivalents for metric specifications are shown in ( ). 020 110A.indd, js 203 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU Code A Code B Code: 5 1-1/4”-14 Tooth Spline 53.8 (2.12) Code: 6 7/8”-13 Tooth Spline 45.5 (1.79) English equivalents for metric specifications are shown in ( ). 020 110A.indd, js 204 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors 110A Series / Serie / Série HY13-1590-005/US,EU 47.7 (1.88) Code: 5 33.0 (1.3) Min Full Spline 1-1/4”-14 Tooth Spline ø 31.153 (1.2265) ø 31.67 (1.247) 3/8-16 UNC thd x 19.05 (.75) Min Deep Code: 6 7/8”-13 Tooth Spline 25.4 (1.00) Min Full Spline 13 Tooth 16/32 ø 25.27 (.995) 1/4-20 UNC thd x 15.75 (.62) Min Deep ø 22.162 (.8725) 1/4-20 UNC-2B x 15.7 (.62) Min Full Thd English equivalents for metric specifications are shown in ( ). 020 110A.indd, js 205 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni / Informacion Tecnica 6 Displacements Series 6 Schluckvolumen 6 Cylindrée Parallel 6 Despazamientos (3.6 – 12.9 in3/rev) 59…211 cm3/rev (7.2 – 25.8 in3/rev) 118…423 cm3/rev Cont Int Maximum Pressure Series Eingangsdruck Pression entrée Parallel Pressione Maxima (to 2500 psi) (to 3000 psi) …170 bar …210 bar (to 2500 psi) (to 3000 psi) …170 bar …210 bar Maximum Oil Flow Series Schluckstrom Débit d’huile Parallel Caudal Maximo de Aceite (to 20 gpm) …76 lpm (to 30 gpm) …114 lpm Maximum Speed Series Drehzahl Parallel Vitesse de rotation Velocidad Maxima 890 rpm 782 rpm Maximum Torque Max Drehmoment Couple Torque Maximo Series Parallel Maximum Side Series Load at Key Seitenlast Charges latèrales Carga Maxima Lateral LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série High Efficiency, High Flow Two-Speed Motor Parker’s patented two-speed motor utilizes two separate IGR™ power elements on a common shaft. An integral selector valve shifts between high torque, low speed (parallel) operation and high speed, low torque (series) mode in a ration of 2:1. The use of two power elements eliminates the deficiencies of traditional, single power element designs. In the high torque mode, the motor delivers twice the torque and half the speed that it does in the high speed mode. The selector valve can be open or closed center and may be actuated by an external pilot or optional solenoid valve. The open center selector valve can be shifted “on the fly” while the motor shaft is rotating under load. The selector valve is spring loaded to return to its pilot-pressure-off position. Normal mode of operation is field changeable and can be selected as series or parallel. Pilot pressure must be 300 psi higher than motor case or outlet pressure and may be as high as typical hydraulic system operating pressure. Cont Int (to 3816 lb in) (to 4694 lb in) …431 Nm …530 Nm (to 6648 lb in) (to 7463 lb in) …751 Nm …843 Nm (to 700 lb) … 3114 N 021 700.indd, js 206 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l Cil ndré luck acem ind e vo lum ent ra t Ma a en x. Ma spe e x Vit . Dre d @ es hz Ma s ah x Ve e loc de l Int . inte ida rot erm rm a it t d m t io it Ma ax n m tiere ent fl x im nd o a Ma . oil x aa er w i flo x Be ca Dé . Sch w t r ie u b da lu b: l in Po it d´h cks t t r ta e rm r ta uile m om i ten ma Ma te x axi x ma Ma . diff x im e re x. o D n Ch ute ruck tial p g r Pr es de p efäll essu ion re e re dif ssio Ma e re n m x. nc Ma sup ia l a x i x p ma Pr . Ein ly pr x im es ga es s a n s Pr ion gs ur es e d m ion ax ruck ma i en Ma x im t ré x. t ad e Ma orq ea x. u e D lim Co en up rehm tac To le m om ion rqu en a x t eM i a Ma x im x o Ma . per f x o Pu . Lei rma st nc is Ma sanc unga e xim e d bg o r e s abe en ort dim ie en max to i LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série cont / int* l/min g/min cont / int* bar psi max bar psi cont / int* Nm lb-in max KW HP 210 3000 276 4000 129 1146 154 1366 8.6 11.5 170 2500 210 3000 276 4000 264 2338 309 2739 15.5 20.8 170 2500 210 3000 276 4000 197 1743 236 2088 12.4 16.6 94.6 25 113.5 170 2500 30 210 3000 276 4000 527 4666 624 5525 26.9 36.1 695 75.7 20 83.3 22 170 2500 210 3000 276 4000 260 2306 313 2769 12.8 17.2 233 14.2 481 113.5 30 113.5 170 2500 30 210 3000 276 4000 518 4592 616 5456 21.8 29.2 176 Series 144 8.8 688 75.7 20 94.6 25 170 2500 210 3000 276 4000 325 2818 392 3472 14.2 19.1 176 Parallel 288 17.6 419 113.5 30 113.5 170 2500 30 210 3000 276 4000 644 5707 709 6283 23.9 32.1 212 Series 174 10.6 580 75.7 20 113.5 155 2250 30 210 3000 276 4000 353 3125 475 4205 13.0 17.4 212 Parallel 347 21.2 352 113.5 30 113.5 155 2250 30 210 3000 276 4000 696 6167 774 6860 21.2 29.4 258 Series 211 12.9 440 75.7 20 113.5 155 2250 30 210 3000 276 4000 431 3816 531 4699 12.3 16.5 258 Parallel 423 25.8 268 113.5 30 113.5 137.9 2000 30 155.1 2250 276 4000 751 6648 843 7463 18.0 24.2 Motor Series 700 cm3/rev in3/rev int rev/min 072 Series 59 3.6 890 45.4 12 53.0 14 170 2500 072 Parallel 118 7.2 782 83.3 22 94.6 25 108 Series 88 5.4 843 60.6 16 68.1 18 108 Parallel 177 10.8 656 142 Series 116 7.1 142 Parallel Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. * Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement inter m. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 021 700.indd, js 207 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos 7 Series 0 X Shaft Welle Arbre Ejes Series LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série XXX X X X Displacement Schluckvolumen Cylindrée Desplazamiento Mounting Gehäuse Carter Montaje Ports Anschluß Plan de raccordement Lumbreras Spool Actuation Spulenbetätigung Actionnement de la bobine Actuado por bobina X Normal Center Position1 Normale Mittenposition Position centrale normale Posición central normal X X Normal Mode of Operation4 Normaler Betriebsmodus Mode opératoire normal Modo normal de operación Paint Anstrich Peinture Pintura Code Code 1" Keyed Remotely Piloted, Closed, Parallel Code 0 SAE A 2-Bolt,Manifold 1-1/4" Keyed PCL AM 3 Remotely Piloted, Open, Parallel SAE A 2-Bolt, 7/8"-14 SAE 1-1/4"-14 Tooth Spline POL AS 5 Solenoid Actuated with Manual Override, Open, Parallel SAE B 2-Bolt, Manifold BM Code cm³/U cm³/tr cm³/giro SOL1 cu in³/rev 072 60 119 / / 108 88 176 / 5.4 Series / 10.8 Parallel SAE B 2-Bolt, 7/8"-14 SAE 3.6 Series 7.2 Parallel 142 116 232 / 7.1 Series / 14.2 Parallel 176 144 289 / 8.8 Series / 17.6 Parallel 212 174 348 / 10.6 Series / 21.2 Parallel 258 211 423 / 12.9 Series / 25.8 Parallel BS 1 Standard Solenoid is 12V DC with 1/4" Spade Connections. Standardausführung ist ein 12-V-Gleichstrom-Solenoid mit 1/4-Zoll-Gabelschuhanschlüssen. Le solénoïde standardisé est du type 12 Vcc avec cosses à fourche de 1/4". La solenoide estándar es para 12 VCC, con conectores tipo bayoneta de 1/4". Code Omit F No Paint Black Paint Schwarz lackiert Consult factory for other available options, configurations ordering codes and lead times. 021 700.indd, js 208 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos 072 Series 8 15 Schluckstrom [L/min] 38 30 23 45 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série 53 4 2 200 US Flow [G/min] 8 10 6 14 12 1750 175 1500 1250 210 3000 170 100 140 75 50 25 1000 2500 psi Torque [lb/in] 125 bar Drehmoment [Nm] 150 750 100 500 70 250 1500 35 0 0 100 200 300 400 500 600 700 800 2000 1000 0 900 0 100 200 300 Drehzahl [1/min] 108 Series 8 15 30 38 45 500 600 700 800 900 500 1000 Speed [Rpm] Flow [G/min] 10 12 14 Schluckstrom [L/min] 23 400 53 61 2 68 4 6 8 16 US 18 2750 300 2500 250 2250 1750 170 100 140 3000 1500 2500 1250 1000 psi 150 Torque [lb/in] 210 bar Drehmoment [Nm] 2000 200 2000 750 100 50 70 0 0 100 200 300 400 500 600 700 800 900 35 1000 500 1500 250 1000 500 0 0 100 200 300 400 500 Speed [Rpm] Drehzahl [1/min] 142 Series 8 15 Schluckstrom [L/min] 23 30 38 45 53 61 600 700 800 900 US Flow [G/min] 68 76 83 2 400 4 6 8 10 12 14 1000 16 18 20 22 3500 350 3000 2500 170 150 Torque [lb/in] 210 200 140 100 100 50 0 0 100 200 300 400 500 600 700 70 35 800 3000 1500 2500 1000 2000 1500 500 0 Drehzahl [1/min] Cont. 2000 psi 250 bar Drehmoment [Nm] 300 0 100 200 300 400 Speed [Rpm] 500 600 700 1000 500 800 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 021 700.indd, js 209 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos 072 Parallel 8 15 23 30 38 Schluckstrom [L/min] 53 61 68 76 45 83 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série 2 95 350 10 12 14 Flow [G/min] 20 22 25 16 18 3000 300 2750 210 2500 250 170 225 Torque [lb/in] 200 150 100 125 bar 140 175 3000 2250 100 2000 2500 1750 2000 1500 1250 1000 75 70 1500 750 50 500 25 35 100 200 300 400 500 600 700 1000 250 0 0 0 800 0 100 200 300 400 500 Speed [Rpm] Drehzahl [1/min] 108 Parallel 8 15 30 38 23 600 700 800 900 500 1000 Schluckstrom [L/min] 45 53 61 68 76 83 95 114 24 6000 650 6 8 10 Flow [G/min] 16 18 20 22 12 14 US 25 30 5500 600 5000 550 500 450 210 4500 170 4000 400 3000 2500 140 300 250 2000 3000 psi 350 Torque [lb/in] 3500 bar Drehmoment [Nm] psi 275 700 US 30 3250 325 Drehmoment [Nm] 6 2500 100 1500 2000 200 150 1500 70 100 1000 1000 50 35 500 0 0 50 100 150 200 250 300 350 400 450 500 550 600 650 500 700 0 0 Drehzahl [1/min] 142 Parallel 8 15 23 30 38 45 53 Schluckstrom [L/min] 61 68 76 83 95 50 100 150 200 250 8 10 12 14 114 700 2 4 6 300 350 400 Speed [Rpm] Flow [G/min] 16 18 20 22 450 500 550 25 600 30 650 700 US 6000 600 5500 5000 500 3000 4500 Torque [lb/in] 140 300 2500 4000 100 200 70 3500 2000 3000 2500 1500 2000 1500 100 psi 170 400 bar Drehmoment [Nm] 210 1000 1000 35 0 0 50 100 150 200 250 300 350 400 450 500 500 550 500 0 0 Drehzahl [1/min] 50 100 150 200 250 300 350 400 450 500 Speed [Rpm] Cont. Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 021 700.indd, js 210 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos 176 Series 15 8 Schluckstrom [L/min] 23 30 38 45 61 68 53 76 83 95 2 4500 450 4000 400 3500 350 6 4 8 Flow [G/min] 14 16 18 20 12 10 Torque [lb/in] 210 200 170 2500 2000 140 2000 500 70 35 0 0 100 200 300 400 500 600 700 2500 1000 100 50 3000 1500 150 100 psi 250 0 100 200 300 Schluckstrom [L/min] 15 30 23 38 45 53 61 400 500 600 700 800 Speed [Rpm] 212 Series 8 1500 1000 500 900 0 800 Drehzahl [1/min] 600 US 25 22 3000 300 bar Drehmoment [Nm] 500 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série 68 76 83 2 95 6 4 8 10 12 Flow [G/min] 14 16 18 20 22 US 25 5000 4500 4000 3500 210 190 170 200 155 140 120 100 100 3000 2750 2000 50 100 150 200 250 300 350 400 450 500 550 600 2250 2000 1750 1500 1000 500 0 650 0 50 1000 500 100 150 200 250 300 350 400 450 500 550 600 650 700 Speed [Rpm] Drehzahl [1/min] 258 Series 15 23 30 38 Schluckstrom [L/min] 45 53 61 68 2 76 83 95 550 5500 500 5000 450 4500 400 6 8 10 Flow [G/min] 12 14 16 18 20 22 US 25 Torque [lb/in] 4000 350 210 300 190 250 170 200 155 150 140 100 120 50 100 70 35 500 0 0 4 6000 50 100 150 200 250 300 350 400 450 bar Drehmoment [Nm] 600 8 3000 2750 2500 2500 2250 2000 2000 1500 1750 1000 500 0 0 Drehzahl [1/min] Cont. 3500 psi 0 2500 1500 70 35 0 3000 2500 psi 300 Torque [lb/in] 400 bar Drehmoment [Nm] 500 50 100 150 200 250 Speed [Rpm] 300 350 400 450 1500 1250 1000 500 500 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 021 700.indd, js 211 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos 176 Parallel 800 8 23 15 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série Schluckstrom [L/min] 30 38 45 53 61 68 76 83 95 2 114 6 4 12 10 8 14 Flow [G/min] 16 18 20 22 US 25 30 7000 6500 700 6000 5500 3500 170 5000 3000 155 4500 140 400 100 300 2500 4000 2000 psi Torque [lb/in] 500 190 bar Drehmoment [Nm] 600 3500 3000 1500 2500 2000 200 70 1000 1500 100 1000 35 500 0 0 50 100 150 200 250 300 350 400 500 0 450 0 50 100 150 Drehzahl [1/min] 212 Parallel 900 8 15 23 30 Schluckstrom [L/min] 38 45 53 61 68 76 83 95 2 114 4 6 8 10 12 200 250 Speed [Rpm] Flow [G/min] 14 16 18 300 20 350 22 400 450 30 25 US 7500 7000 800 6500 5500 600 Torque [lb/in] 140 500 120 400 100 300 2250 5000 155 2000 4500 4000 1750 3500 1500 3000 1250 2500 85 1000 2000 200 70 1500 1000 100 0 25 50 75 0 100 125 150 175 200 225 250 275 300 325 350 375 400 0 25 50 75 4 6 8 Drehzahl [1/min] 258 Parallel 8 15 23 30 Schluckstrom [L/min] 38 45 53 61 68 76 83 95 2 114 155 700 Torque [lb/in] 140 600 120 500 100 400 bar Drehmoment [Nm] 800 85 300 70 200 100 35 0 25 Cont. 50 75 100 125 150 175 Drehzahl [1/min] 200 225 250 10 Flow [G/min] 12 14 16 18 20 22 25 US 30 8500 900 0 100 125 150 175 200 225 250 275 300 325 350 Speed [Rpm] 275 300 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 500 0 2250 2000 1750 1500 psi 0 500 500 35 1000 psi 170 bar Drehmoment [Nm] 2500 6000 700 1250 1000 500 0 25 50 75 100 125 150 175 Speed [Rpm] 200 225 250 275 300 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 021 700.indd, js 212 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mode of Operation / Betriebsmodus Mode opératoire / Modo de operación LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série 021 700.indd, js 213 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série 700 Series Roller Bearing Allowable Radial Load Curve Chart A Radial Load - N (lbs) 35586 (8000) 26689 (6000) 17793 (4000) 8896 (2000) 0 -50.8 (-2.0) -25.4 (-1.0) 0 25.4 (1.0) 50.8 (2.0) Distance From Flange Face - mm (in) The allowable side load curve is based on L10 bearing life of 2.5 x 106 revolutions. Die zulassige radiale Wellenbelastung bezieht sich auf die Lager-Lebensdauer 2.5 x 106 Umdrehungen. L’effort radial admissible sur l’arbre depend a une duree de vie 2.5 x 106 de rotation. La curva de carga lateral admisible se basa en vida util de cojinete de 2.5 x 106 revoluciones. Bearing Life Factor Curve Chart B Multiply Allowable Radial Load by these Factors 4 Note: Side load should be considered a vector sum of all imposed loads. 3 2 1 0 0 2 8 10 12 4 6 Life in Millions of Revolutions 021 700.indd, js 214 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras Code: AM SAE A, Manifold ø 14.034 (.5525) x 1.2954 (.051) LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série 7/16-20 SAE O-Ring or 1/4 BSPP Case Drain 2x 34.29 2x 23.01 (1.35) (.906) 14.5 (.57) 3.3 (.13) 48.51 (1.910) 2x 18.0 (.71) 2x 18.8 (.74) 15.5 (.61) 4x 5/16-18 UNC-2B x 12.7 (.50) Min Full Thread O-rings Code AM Weight/Gewicht kg Poids/Peso (lb) Length "L1" mm "L1" (in) "L2" mm "L2" (in) 130.8 (5.15) 2.03 (0.80) ø20.62 (.812) x 2.03 (.080) Deep L2 14.0 (.55) Motor with manifold mount is supplied with 2 O-rings. Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni é corredato da 2 OR. 20.62 (0.812) L1 106.4 (4.188) A ø 114.3 (4.50) ø 82.52 (3.249) B 44.45 (1.750) 95.25 (3.750) 072 108 142 176 212 258 15.9 (35.0) 214.6 (8.45) 123.2 (4.85) 16.1 (35.4) 224.3 (8.83) 128.0 (5.04) 16.2 (35.7) 233.7 (9.20) 132.9 (5.23) 16.4 (36.1) 243.3 (9.58) 137.7 (5.42) 16.6 (36.5) 253.2 (9.97) 142.5 (5.61) 16.8 (37.0) 266.0 (10.47) 148.8 (5.86) Code: AS SAE A, 7/8"-14 SAE 7/16-20 SAE O-Ring or 1/4 BSPP Case Drain Pilot Port 7/16-20 SAE O-Ring 7/8-14 SAE O-Ring 14.5 (.57) 3.3 (.13) ø 114.3 (4.50) 44.5 (1.75) 15.5 (.61) ø 82.52 (3.249) A 52.3 (2.06) 106.4 (4.188) B 2x 18.0 (.71) 130.8 (5.15) 18.8 (.74) 37.6 (1.48) 14.0 (.55) L2 L1 Code AS Weight/Gewicht kg Poids/Peso (lb) Length "L1" mm "L1" (in) "L2" mm "L2" (in) 072 108 142 176 212 258 15.9 (35.0) 214.6 (8.45) 123.2 (4.85) 16.1 (35.4) 224.3 (8.83) 128.0 (5.04) 16.2 (35.7) 233.7 (9.20) 132.9 (5.23) 16.4 (36.1) 243.3 (9.58) 137.7 (5.42) 16.6 (36.5) 253.2 (9.97) 142.5 (5.61) 16.8 (37.0) 266.0 (10.47) 148.8 (5.86) English equivalents for metric specifications are shown in ( ). 021 700.indd, js 215 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série Code: BM SAE B, Manifold ø 14.034 (.5525) x 1.2954 (.051) 7/16-20 SAE O-Ring or 1/4 BSPP Case Drain 2x 34.29 2x 23.01 (1.35) (.906) 14.5 (.57) 6.22 (.245) 3.3 (.13) ø 101.57 (3.999) 48.51 (1.910) 2x 18.0 (.71) 4x 5/16-18 UNC-2B x 12.7 (.50) Min Full Thread 2x 18.8 (.74) 15.5 (.61) ø20.62 (.812) x 2.03 (.080) Deep L2 O-rings L1 2.03 (0.80) 20.62 (0.812) Code BM Weight/Gewicht kg Poids/Peso (lb) Length "L1" mm "L1" (in) "L2" mm "L2" (in) 176.0 (6.93) A ø 114.3 (4.50) 145.8 (5.74) B 44.45 (1.750) 95.25 (3.750) ø 13.49 (.531) Motor with manifold mount is supplied with 2 O-rings. Zum Motor mit Universalanschluß werden 2 O-Ringe geliefert. Deux joints toriques sont livrés avec les moteurs a plan de raccordement universel. Il blocchetto connessioni é corredato da 2 OR. 072 108 142 176 212 258 15.9 (35.0) 214.6 (8.45) 123.2 (4.85) 16.1 (35.4) 224.3 (8.83) 128.0 (5.04) 16.2 (35.7) 233.7 (9.20) 132.9 (5.23) 16.4 (36.1) 243.3 (9.58) 137.7 (5.42) 16.6 (36.5) 253.2 (9.97) 142.5 (5.61) 16.8 (37.0) 266.0 (10.47) 148.8 (5.86) Code: BS SAE B, 7/8"-14 SAE 7/8-14 SAE O-Ring 7/16-20 SAE O-Ring or 1/4 BSPP Case Drain Pilot Port 7/16-20 SAE O-Ring 14.5 (.57) 6.22 (.245) ø 101.57 (3.999) A 52.3 (2.06) 145.8 (5.74) B ø 114.3 (4.50) 44.5 (1.75) 176.0 (6.93) 2x 18.0 (.71) 15.5 (.61) 18.8 (.74) 37.6 (1.48) L2 ø 13.49 (.531) L1 Cod e BS Weight/Gewicht kg Poids/Peso (lb) Length "L1" mm "L1" (in) "L2" mm "L2" (in) 072 108 142 176 212 258 15.9 (35.0) 214.6 (8.45) 123.2 (4.85) 16.1 (35.4) 224.3 (8.83) 128.0 (5.04) 16.2 (35.7) 233.7 (9.20) 132.9 (5.23) 16.4 (36.1) 243.3 (9.58) 137.7 (5.42) 16.6 (36.5) 253.2 (9.97) 142.5 (5.61) 16.8 (37.0) 266.0 (10.47) 148.8 (5.86) English equivalents for metric specifications are shown in ( ). 021 700.indd, js 216 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Spool Actuation / Spulenbetätigung Actionnement de la bobine / Actuado por bobina LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série Code: PCL Remotely Piloted, Closed, Parallel 124.0 (4.88) Code: POL Remotely Piloted, Open, Parallel 124.0 (4.88) Code: SOL Solenoid Actuated with Manual Override, Open, Parallel Auxillary Actuation Port 7/16-20 SAE O-Ring 164.6 (6.48) Auxillary Drain Port 7/16-20 SAE O-Ring High Speed Series Mode A B High Torque Parallel Mode Optional Solenoid Valve A B Optional Solenoid Valve B A B A Master Spool Master Spool C Pilot C Pilot Series Mode Master Spool Piloted Solenoid Energized Double Power Elements Parallel Mode Master Spool Piloted Solenoid De-Energized Double Power Elements Add .5 kg (1.1 lb) for this option. English equivalents for metric specifications are shown in ( ). 021 700.indd, js 217 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série Code A Code B Code: 0 1” Keyed 45.7 (1.80) Code: 3 1-1/4” Keyed 54.1 (2.13) Code: 5 1-1/4”-14 Tooth Spline 54.1 (2.13) English equivalents for metric specifications are shown in ( ). 021 700.indd, js 218 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / EJes Code: 0 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 700 Series / Serie / Série 18.6 (.73) Key 1/4 x 1 Woodruff 1" Keyed #15 Per SAE J502 6.37 (.251) 28.4 (1.120) ø 25.37 (.999) 1/4-20 UNC thd x 15.75 (.62) Min Deep 47.8 (1.88) 39.4 (1.55) x 7.95 (.313) Code: 3 1-1/4" Keyed 7.96 (.3135) ø 31.737 (1.2495) 34.9 (1.373) 3/8-16 UNC thd x 19.05 (.75) Min Deep Key 7.950 x 31.5 (.3130 x 1.24) Square Code: 5 47.7 (1.88) 33.0 (1.3) Min Full Spline 1-1/4"-14 Tooth Spline ø 31.153 (1.2265) 3/8-16 UNC thd x 19.05 (.75) Min Deep ø 31.67 (1.247) English equivalents for metric specifications are shown in ( ). 021 700.indd, js 219 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information /Technische Information / Segni / Informacion Tecnica 6 Displacements Series 6 Schluckvolumen 6 Cylindrée Parallel 6 Despazamientos (3.6 – 12.9 in3/rev) 59…211 cm3/rev (7.2 – 25.8 in3/rev) 118…423 cm3/rev Cont Maximum Pressure Eingangsdruck Pression entrée Presion Maxima Series Parallel Int (to 2500 psi) (to 3000 psi) …170 bar …210 bar (to 2000 psi) (to 2500 psi) …140 bar …170 bar Maximum Oil Flow Series Schluckstrom Débit d’huile Parallel Caudal Maximo de Aceite (to 20 gpm) …76 lpm (to 30 gpm) …114 lpm Maximum Speed Series Drehzahl Parallel Vitesse de rotation Velocidad Maxima 890 rpm 782 rpm Maximum Torque Max Drehmoment Couple Torque Maximo Series Parallel Maximum Side Series Load at Key Seitenlast Charges latèrales Carga Maxima Lateral LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série High Efficiency, High Flow Two-Speed Motor Parker’s patented two-speed motor utilizes two separate IGR™ power elements on a common shaft. An integral selector valve shifts between high torque, low speed (parallel) operation and high speed, low torque (series) mode in a ration of 2:1. The use of two power elements eliminates the deficiencies of traditional, single power element designs. In the high torque mode, the motor delivers twice the torque and half the speed that it does in the high speed mode. The selector valve can be open or closed center and may be actuated by an external pilot or optional solenoid valve. The open center selector valve can be shifted “on the fly” while the motor shaft is rotating under load. The selector valve is spring loaded to return to its pilot-pressure-off position. Normal mode of operation is field changeable and can be selected as series or parallel. Pilot pressure must be 300 psi higher than motor case or outlet pressure and may be as high as typical hydraulic system operating pressure. Cont Int (to 3125 lb in) (to 3844 lb in) …353 Nm …434 Nm (to 3735 lb in) (to 4666 lb in) …422 Nm …527 Nm (to 700 lb) … 3114 N 022 716.indd, js 220 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos Ge o Ge metr om ic Cy . S disp ch li l Cil ndré luck acem ind e vo lum ent ra t Ma a en x. Ma spe e x Vit . Dre d @ es hz Ma s ah x Ve e loc de l Int . inte ida rot erm rm a it t d m t io it Ma ax n m tiere ent fl x im nd o a Ma . oil x aa er w i flo x Be ca Dé . Sch w t rie u b da lu b: l in Po it d´h cks t t r ta e rm r ta uile m om i t en ma Ma te x axi x ma Ma . diff x im e re x. o D n Ch ute ruck tial p g r Pr es de p efäll essu ion re e re dif ssio Ma e re n m x. nc Ma sup ia l a x i x p ma Pr . Ein ly pr xim es ga es s a n s Pr ion gs ur es e d m ion ax ruck ma i en Ma x im t ré x. ad e Ma torq ea x. u e D lim Co en up rehm tac To le m om ion rqu en a x t eM i ax Ma im x o Ma . per f x. o r Pu Lei ma st nc is Ma sanc unga e xim e d bg o r e s abe en ort dim ie en max to i LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série cont / int l/min g/min cont / int bar psi max bar psi cont / int Nm lb-in Motor Series 700 cm3/rev in3/rev int rev/min 072 Series 59 3.6 890 45.4 12 53.0 14 170 2500 210 3000 276 4000 129 1146 154 1366 8.6 11.5 072 Parallel 118 7.2 782 83.3 22 94.6 25 170 2500 210 3000 276 4000 264 2338 309 2739 15.5 20.8 108 Series 88 5.4 843 60.6 16 68.1 18 170 2500 210 3000 276 4000 197 1743 236 2088 12.4 16.6 108 Parallel 177 10.8 656 94.6 30 113.5 30 140 2000 170 2500 276 4000 422 3735 527 4666 22.2 29.8 142 Series 116 7.1 695 75.7 20 83.3 22 170 2500 210 3000 276 4000 260 2306 313 2769 12.8 17.2 142 Parallel 233 14.2 481 113.5 30 113.5 30 100 1500 140 2000 276 4000 314 2780 418 3699 12.8 17.2 176 Series 144 8.8 688 75.7 20 94.6 25 170 2500 210 3000 276 4000 325 2818 392 3472 14.1 19.0 176 Parallel 288 17.6 419 113.5 30 113.5 30 85 1250 100 1500 276 4000 321 2843 386 3423 11.1 14.9 212 Series 174 10.6 580 75.7 20 94.6 25 155 2250 190 2750 276 4000 353 3125 434 3844 12.9 17.3 212 Parallel 347 21.2 352 113.5 30 113.5 30 85 1250 100 1500 276 4000 385 3407 464 4107 11.3 15.2 258 Series 211 12.9 440 68.1 18 94.6 25 120 1750 155 2250 276 4000 332 2926 431 3816 8.8 11.8 258 Parallel 423 25.8 268 113.5 30 113.5 30 70 1000 85 1250 276 4000 371 3285 467 4134 7.8 10.5 Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. max KW HP * Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 022 716.indd, js 221 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Ordering Information / Bestellschlüssel System de Commande / Imformacion para pedidos 7 1 6 XXX BS Series Series Shaft Welle Arbre Ejes Displacement Schluckvolumen Cylindrée Desplazamiento Mounting/Ports Gehäuse/Anschluß Carter/Plan de raccordement Montaje/Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série X X X X Spool Actuation Normal Center Normal Mode Spulenbetätigung of Operation4 Position1 Normale Normaler Actionnement Mittenposition Betriebsmodus de la bobine Position Mode opératoire Actuado por bobina centrale normale normal Posición Modo normal central normal de operación Paint Anstrich Peinture Pintura Code Code 7/8"-13 Tooth Spline Remotely Piloted, Closed, Parallel Code 6 SAE B 2-Bolt, 7/8"-14 SAE PCL BS Code cm³/U cm³/tr cm³/giro Solenoid Actuated without Manual Override, Open, Parallel NOL1 cu in³/rev 072 60 / 119 / 3.6 Series 7.2 Parallel 108 88 / 5.4 Series 176 / 10.8 Parallel 142 116 / 232 / 71.1 Series 14.2 Parallel 176 144 / 289 / 8.8 Series 17.6 Parallel 212 174 / 348 / 10.6 Series 21.2 Parallel 258 211 / 12.9 Series 423 / 25.8 Parallel 1 Standard Solenoid is 12V DC with 1/4" Spade Connections. Standardausführung ist ein 12-V-Gleichstrom-Solenoid mit 1/4-Zoll-Gabelschuhanschlüssen. Le solénoïde standardisé est du type 12 Vcc avec cosses à fourche de 1/4". La solenoide estándar es para 12 VCC, con conectores tipo bayoneta de 1/4". Code Omit F No Paint Black Paint Schwarz lackiert Consult factory for other available options, configurations ordering codes and lead times. 022 716.indd, js 222 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos 072 Series 8 15 Schluckstrom [L/min] 38 30 23 45 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série 53 2 200 4 Flow [G/min] 8 10 6 US 12 14 1750 175 1500 1250 210 3000 170 100 140 75 50 100 25 70 1000 2500 psi Torque [lb/in] 125 bar Drehmoment [Nm] 150 750 2000 500 1500 250 1000 35 0 0 100 200 300 400 500 600 700 800 0 100 200 300 Drehzahl [1/min] 108 Series 8 15 Schluckstrom [L/min] 23 38 30 45 53 61 500 1000 0 900 6 4 2 68 400 500 Speed [Rpm] 8 600 700 800 Flow [G/min] 14 12 10 16 18 900 US 2750 300 2500 250 2250 1750 170 140 100 3000 1500 2500 1250 1000 psi 150 Torque [lb/in] 210 bar Drehmoment [Nm] 2000 200 2000 750 100 50 70 0 0 100 200 300 400 500 600 700 800 900 35 1000 500 1500 250 1000 0 100 200 300 400 500 Speed [Rpm] Drehzahl [1/min] 142 Series 400 8 15 23 Schluckstrom [L/min] 30 38 45 53 61 68 76 2 83 4 6 8 10 600 Flow [G/min] 14 12 16 700 18 800 20 900 US 22 3500 350 3000 300 2500 100 50 2500 140 1000 2000 100 500 70 35 0 0 100 200 300 400 500 600 700 800 1500 0 Drehzahl [1/min] Cont. 3000 1500 170 150 2000 psi 210 200 0 Torque [lb/in] 250 bar Drehmoment [Nm] 500 1000 0 100 200 300 400 Speed [Rpm] 500 600 700 1000 500 800 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 022 716.indd, js 223 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série 072 Parallel Flow [G/min] 18 20 22 Schluckstrom [L/min] 8 15 23 350 30 45 38 53 61 68 76 83 2 4 6 95 10 12 14 16 US 25 3250 3000 325 2750 300 210 2500 250 3000 2250 Torque [lb/in] 170 225 200 140 175 bar 150 125 100 2000 2500 1750 1500 2000 1250 1500 1000 100 psi 275 Drehmoment [Nm] 8 750 75 70 50 500 25 250 35 0 0 100 200 300 400 500 600 700 800 1000 500 1000 0 900 0 100 200 300 Drehzahl [1/min] 400 500 Speed [Rpm] 600 700 800 900 108 Parallel 550 8 15 23 30 38 45 Schluckstrom [L/min] 53 61 68 76 83 95 6 2 4 114 8 10 12 14 Flow [G/min] 16 18 20 US 22 30 25 5000 500 4500 450 170 4000 2500 3500 350 250 100 200 150 2000 3000 psi Torque [lb/in] 140 300 bar Drehmoment [Nm] 400 2500 1500 2000 1500 70 1000 100 1000 50 500 35 500 0 0 50 100 150 200 250 300 350 400 450 500 550 600 650 0 700 0 50 Drehzahl [1/min] 100 150 200 250 300 350 400 450 500 550 600 650 700 Speed [Rpm] 142 Parallel Schluckstrom [L/min] 8 15 23 30 38 45 53 61 68 76 83 95 2 114 4 6 8 10 12 Flow [G/min] 14 16 18 20 22 25 30 US 4000 600 3500 500 2000 300 100 200 1500 2000 psi Torque [lb/in] 2500 140 bar Drehmoment [Nm] 3000 400 1500 1000 1000 70 100 500 500 35 0 0 50 100 150 200 250 300 350 400 450 500 0 550 Drehzahl [1/min] Cont. 0 50 100 150 200 250 Speed [Rpm] 300 350 400 450 500 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 022 716.indd, js 224 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos 176 Series 15 8 23 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série Schluckstrom [L/min] 30 38 45 53 61 68 76 83 2 95 500 6 8 10 12 Flow [G/min] 14 16 18 20 22 25 30 US 3500 450 400 3000 350 1500 2500 210 200 170 1250 2000 psi 250 Torque [lb/in] 300 bar Drehmoment [Nm] 4 4000 1000 1500 150 140 1000 100 100 50 0 0 100 200 300 400 500 600 700 500 70 35 800 0 500 0 50 100 150 200 250 Speed [Rpm] Drehzahl [1/min] 212 Series 600 8 15 23 Schluckstrom [L/min] 30 38 45 53 61 68 76 83 4 2 95 8 6 10 12 Flow [G/min] 14 16 18 300 350 400 450 US 20 22 25 5000 4500 500 3500 400 190 170 200 2750 2000 50 2500 2250 1000 2000 1750 1500 500 70 35 100 150 200 250 300 350 400 450 500 550 600 650 700 0 1500 1000 500 100 150 200 250 300 350 400 450 500 550 600 650 700 Speed [Rpm] 0 0 50 Drehzahl [1/min] 258 Series 500 8 15 23 30 38 Schluckstrom [L/min] 45 53 61 68 76 83 95 4500 450 2 4 6 8 10 12 Flow [G/min] 14 16 18 20 22 25 30 US 4000 400 3500 1500 350 3000 300 Torque [lb/in] 140 150 120 100 100 50 85 0 50 100 150 200 250 300 350 400 450 2000 1000 1500 1000 500 500 70 35 500 0 Drehzahl [1/min] Cont. psi 155 200 0 1250 2500 250 bar Drehmoment [Nm] psi 2500 155 140 120 100 100 0 3000 Torque [lb/in] 300 bar Drehmoment [Nm] 4000 0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 Speed [Rpm] Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 022 716.indd, js 225 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Performance Data / Leistungsdaten Puissance / Datos Tecnicos 176 Parallel 15 8 30 23 LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série Schluckstrom [L/min] 38 45 53 61 68 76 83 95 2 114 4 6 8 10 12 Flow [G/min] 14 16 18 US 20 22 25 30 4000 600 3500 500 1500 100 300 85 200 70 1250 2000 psi Torque [lb/in] 2500 bar Drehmoment [Nm] 3000 400 1000 1500 1000 100 35 500 500 0 0 50 100 150 200 250 300 350 400 450 0 0 Drehzahl [1/min] 212 Parallel 8 15 23 50 100 150 Schluckstrom [L/min] 30 38 45 53 61 68 76 83 95 114 2 4500 600 4 6 8 10 12 200 250 Speed [Rpm] Flow [G/min] 14 16 18 300 350 400 450 US 20 22 25 30 4000 500 3500 3000 100 Torque [lb/in] 1250 85 200 psi 2500 300 2000 bar Drehmoment [Nm] 1500 400 70 1000 1500 1000 100 35 500 500 0 0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 0 Drehzahl [1/min] 258 Parallel 600 8 15 23 30 Schluckstrom [L/min] 38 45 53 61 68 76 83 95 0 114 4500 25 2 50 4 75 6 100 125 150 175 200 225 250 275 300 325 350 375 Speed [Rpm] 8 10 12 Flow [G/min] 14 16 18 20 US 22 25 30 4000 500 1250 3000 300 70 200 100 2500 1000 2000 psi Torque [lb/in] 85 bar Drehmoment [Nm] 3500 400 1500 1000 35 500 0 0 25 50 75 100 125 150 175 200 225 250 275 0 Drehzahl [1/min] Cont. 500 300 0 25 50 75 100 125 150 175 Speed [Rpm] 200 225 250 275 300 Int. Intermittent operation rating applies to 10% of every minute. Intermittierende Werte maximal 10% von jeder Betriebsminute. Fonctionnement interm. 10% max. de chaque minute d`utilisation. Capacidad de funcionamiento intermitente valida para 10% por cada minuto. Performance data based on tests using 15W40 oil with a viscosity of 55 cSt (215 SUS) at 54° C (130° F.) Performance data is typical. Actual data may vary slightly from one production motor to another. Leistugsdaten sind gemessen mit SAE 15W40 bei einer Viskositaet von 43,1 Cst beo 54°C. Geringfuegige Abweichungen von den Katalogerten sond moeglich. Les donnees sur les performances sont basees sur des tests utilisant de l’huile 15W40 d’une viscosite de 55 cSt (215 SUS) a 54°C (130°F). Ces donnees correspondent a des situations typiques. Les donnees reelles peuvent varier legerement d’un moteur de production a l’autre. Datos tecnicos obtenidos con aceite 15W40 de 55 cSt (215 SUS) de viscosidad a 54°C (130°F). Los datos proporcionados son valores tipcos. Los valores exactos reales podrian tener una pequena variacion entre distintos motores. 022 716.indd, js 226 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Radial Load / Radiale Wellenbelastung Charges Radiale / Carga Radial LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série 11120 (2500) Radial Load - N (lbs) 8896 (2000) 6672 (1500) 4448 (1000) 2224 (500) -12.7 (-.5) 0 12.7 25.4 38.1 50.8 (.5) (1.0) (1.5) (2.0) Distance From Flange Face - mm (in) The allowable side load curve is based on a L10 bearing life of 2.5 x 106 revolutions. Die zulassige radiale Wellenbelastung bezieht sich auf die Lager-Lebensdauer 2.5 x 106 Umdrehungen. L’effort radial admissible sur l’arbre depend a une duree de vie 2.5 x 106 de rotation. La curva de carga lateral admisible se basa en vida util de cojinete de 2.5 x 106 revoluciones. Bearing Life Factor Curve Chart B Multiply Allowable Radial Load by these Factors 4 Note: Side load should be considered a vector sum of all imposed loads. 3 2 1 0 0 2 8 10 12 4 6 Life in Millions of Revolutions 022 716.indd, js 227 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Mounting,Ports/Gehäuse,Anschlüße Carter,Orifices / Montaje,Lumbreras LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série Code: BS SAE B, 7/8"-14 SAE Pilot Port 7/16-20 SAE O-Ring 120.7 (4.75) 14.5 (.57) 7/16-20 SAE O-Ring or 1/4 BSPP Case Drain 6.22 (.245) 7/8-14 SAE O-Ring 2x 18.0 (.71) ø 101.57 (3.999) 15.5 (.61) 18.8 (.74) A 52.3 (2.06) 145.8 (5.74) B 44.5 ø 114.3 (1.75) (4.50) 176.0 (6.93) 37.6 (1.48) L2 ø 13.49 (.531) L1 Cod e BS Weight/Gewicht kg Poids/Peso (lb) Length "L1" mm "L1" (in) "L2" mm "L2" (in) 072 108 142 176 212 258 14.8 (32.7) 182.6 (7.18) 91.4 (3.60) 15.2 (33.6) 192.3 (7.57) 96.3 (3.79) 15.4 (33.9) 201.7 (7.94) 101.8 (3.97) 15.6 (34.3) 211.3 (8.32) 105.7 (4.16) 15.7 (34.7) 221.2 (8.71) 110.7 (4.36) 15.9 (35.2) 234.0 (9.21) 117.1 (4.61) English equivalents for metric specifications are shown in ( ). 022 716.indd, js 228 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Spool Actuation / Spulenbetätigung Actionnement de la bobine / Actuado por bobina LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série Code: PCL Remotely Piloted, Closed, Parallel 124.0 (4.88) Code: NOL Solenoid Actuated without Manual Override, Open, Parallel Auxillary Actuation Port 7/16-20 SAE O-Ring Auxillary Drain Port 7/16-20 SAE O-Ring 164.6 (6.48) High Speed Series Mode A B High Torque Parallel Mode Optional Solenoid Valve A B Optional Solenoid Valve B A B A Master Spool Master Spool C Pilot C Pilot Series Mode Master Spool Piloted Solenoid Energized Parallel Mode Master Spool Piloted Solenoid De-Energized Double Power Elements Double Power Elements Add .5 kg (1.1 lb) for this option. English equivalents for metric specifications are shown in ( ). 022 716.indd, js 229 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Shafts / Abtriebswellen Arbre / Ejes LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 716 Series / Serie / Série Code: 6 7/8"-13 Tooth Spline 45.7 (1.80) Code: 6 25.4 (1.00) Min Full Spline 13 Tooth 16/32 ø 25.27 (.995) 7/8"-13 Tooth Spline 1/4"-20 UNC thd x 15.75 (.62) Min Deep ø 22.162 (.8725) 1/4"-20 UNC-2B x 15.75 (.62) Min Full Thd English equivalents for metric specifications are shown in ( ). 022 716.indd, js 230 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Cross-Over Relief Valve / Schockventil LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Valve anti-choc / Vavola di soprapressione Nichols™ Options Specifications Spécifications • Rated flow — 20 gpm • Max. Operating Pressure — adjustable up to 3500 psi, factory preset at 1750 psi. • Reseat Pressure — 90% of set pressure • Operating Temperature Range: -40°F to 250°F • Cartridge Material — All parts steel. All operating parts hardened steel. • Body Material — Steel • Débit nominal – 75,7 litres/minute (20 gallons/minute) • Pressure de service maximale – ajustable jusqu’à 246 kg/cm2 (3 500 ppo2), préréglée à l’usine à 123 kg/cm2 (1 750 ppo2). • Pression de rajustage – 90% de la pression de consigne • Gamme des températures de service – de – 40° C à 121° C (-40° F à 250° F). • Matériau de la cartouche – Entièrement en acier. Toutes les pièces de service en acier durci. • Matériau du corps – Acier Einsatzdaten • • • • • • Max. Fluß 76l/min. Max. Druck 240 bar (Voreinstellung 120 bar) Hysterese 90% des Öffnungsdrucks Betriebstemperatur –40°C bis 115°C Ventil in Stahlausführung Code für Ausführung schwarz grundiert Especificaciones técnicas • Caudal: 20 galones/minuto • Presión máxima de servicio: regulable hasta 3.500 libras/ pulg.2. Regulada de fábrica a 1.750 libras/pulg.2. • Presión de reasentamiento: 90% de la presión calibrada. • Gama de temperatura de servicio: - 40° F a 250° F • Material del cartucho: todas las partes son de acero. Todas las partes activas son de acero templado. • Material del cuerpo: acero Consult factory for other available options, configurations ordering codes and lead times. 85.3 (3.36) Max 47.5 (1.87) 69.9 (2.75) 50.8 (2.00) 23.9 (.94) 7.9 (.31) 8.9 (.350) 55.6 (2.19) 28.6 (1.125) 33.3 (1.31) 45.7 (1.800) 63.5 (2.500) 79.2 (3.12) 1/4" Hollow Hex Schraubenmoment 34 Nm (Bolt Torque 25 ft lb) Top View 14.3 (.562) 12.57(.495) Dia. 2 x 9/16-18 SAE Str thd Port Rear View Bottom View Performance Curve 34.5 (1.36) 50.8 (2.00) Ref 275.8 (4000) Flow vs. Pressure Inlet Pressure-bar (PSI) 241.3 (3500) 15.5 (.61) Side View 206.8 (3000) Hydraulic Oil 100 SUS 172.4 (2500) 137.9 (2000) 103.4 (1500) 69.0 (1000) 34.5 (500) 0 0 18.9 (5) 37.9 (10) 56.8 (15) 75.7 (20) Flow (GPM) English equivalents for metric specifications are shown in ( ). 023 Nichols Options.indd, js 231 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Encoder Mount / Impulsscheiben-Befestigungsplatte montage de l’encodeur / el codificador ø 114.3 (4.50) LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Nichols™ Options Pilot Options Code Pilot E ø62.0 (2.44) ø 9.50 (.374) A ø 108.0 (4.25) 20˚ 25˚ B 11.7 (.46) Flat Length 4x 4.6 (.18) Thru on a ø 74.98 (2.952) BC 10.4 (.41) Shaft Length "L" + 13.5 (.53) Note: To mount encoder, remove (4) socket head cap screws attaching rear encoder mounting plate to motor. Attach encoder and encoder mounting plate to motor using (4) longer socket head cap screws, furnished. Torque to 10 lb in. Hinweis: Zur Montage der Impulsscheibe zunächst die vier Sechskantkopfschrauben lösen, mit denen die hintere Impulsscheiben-Befestigungsplatte am Motor angeschraubt ist. Zum Anschrauben von Impulsscheibe und Impulsscheiben-Befestigungsplatte am Motor die bereitgestellten vier längeren Sechskantkopfschrauben verwenden. Maximal zulässiges Drehmoment: 1,13 Nm (10 lb in). Remarque : Pour monter l’encodeur, enlever les (4) vis à tête creuse qui retiennent la plaque de montage arrière de l’encodeur au moteur. Attacher l’encodeur et la plaque de montage de l’encodeur au moteur à l’aide des (4) longues vis à tête creuse fournies. Serrer jusqu’à 10 liv.po. Nota: Para montar el codificador, quitar los (4) tornillos de cabeza hueca que fijan la placa del codificador al motor. Fijar el codificador y la placa al motor, usando los (4) tornillos más largos que se suministran. Ajustarlos con un torque de 10 libras-pulgada. Consult factory for other available options, configurations ordering codes and lead times. Standard Length & Weights for 700 Series on Page 202-203, 716 Series on Page 216. Längen/Gewichte 700 Serie siehe Seiten 202-203, 716 Serie siehe Seiten 216. Longueurs et poids courants pour la série 700, voir les pages 202-203, série 716, voir les pages 216. Los valores estándar de longitud y peso de la Serie 700 se puede ver en las Páginas 202-203, Serie 716 se puede ver en las Páginas 216. English equivalents for metric specifications are shown in ( ). 023 Nichols Options.indd, js 232 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Thru-Shaft / durchgehende Welle arbre traversant / Eje pasante LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Nichols™ Options 38.6 (1.52) 27.9 (1.10) Min Full Spline IN ø 21.06 (.829) OD 146.1 (5.75) A ø 63.47 (2.499) IN B 13 Tooth 16/32 Spline 4.01 (.158) 1/2-13 UNC "L" + 2.54 (.10) Note: Torque Rating: Maximum torque should not exceed 339 Nm (3000 lb in) in dynamic on the thru-shaft. Consult factory if the radial load on the thru-shaft exceed 1780 N (400 lb). Hinweis: Drehmoment-Grenzwert: Das statische Drehmoment auf die durchgehende Welle darf höchstens 339 Nm (3000 lb in) betragen. Wenn die radiale Querbelastung auf die durchgehende Welle größer als 1780 N (400 lb) ist, vom Herstellerwerk beraten lassen. Remarque : Couple: Le couple maximal ne devrait pas dépasser 339 Nm (3000 liv. po.) dynamique sur l’arbre traversant. Consulter l’usine si la charge radiale sur l’arbre traversant dépasse 1780 N (400 livres). Nota: Valor de torque: el torque máximo en el eje pasante no debe superar 339 N-m (3000 libras-pulgada) dinámico. Si la carga radial sobre el eje pasante superara 1780 N (400 libras), consultar a fábrica. WARNING If torque on the thru-shaft exceeds 339 Nm (3000 lb in) when attempting to dynamically brake a load, the thru-shaft splines and/or shaft could fail and all braking action could be lost. WARNUNG Wenn beim Versuch, die Last dynamisch abzubremsen, das Drehmoment auf die Welle größer als 339 Nm (3000 lb in) wird, können die Keilwellenverbindung und/oder die Welle versagen und alle Bremswirkung verloren gehen. AVERTISSEMENT Si le couple sur l’arbre traversant dépasse 339 Nm (3000 liv. po.) au moment d’essayer le freinage dynamique d’une charge, les cannelures de l’arbre traversant et/ou l’arbre pourraient échouer et toute action de freinage pourrait être perdue. ADVERTENCIA Si el torque en el eje pasante superara 339 N-m (3000 libras-pulgada) al intentar frenar una carga dinámicamente, las estrías del eje o el mismo eje podrían fallar, perdiéndose la acción de frenado. Standard Length & Weights for 110A Series on Pages 187-189. Längen/Gewichte 110A Serie siehe Seiten 187-189. Longueurs et poids courants pour la série 110A, voir les pages 187-189. Los valores estándar de longitud y peso de la Serie 110A se puede ver en las Páginas 187-189. Consult factory for other available options, configurations ordering codes and lead times. English equivalents for metric specifications are shown in ( ). 023 Nichols Options.indd, js 233 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Options LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Nichols™ Options Stainless Steel Shaft Encoder Mount Standard, 2.44 Pilot External Relief Valve - adjustable up to 3500 psi, factory preset at 1750 psi. Thru Shaft with Brake Mount Consult Factory for Other Positions * To order crossover relief valve mounted on a specific motor see the ordering information for that motor. To order crossover relief valve as a field conversion or a spare part consult factory for part number. Mounting bolts are available as 5/16-18 socket head cap screw (4 required) as well as 2 o-rings. Consult factory for part number. * Zur Bestellung eines bestimmten Motors mit werkseitig montiertem Bremsdruckbegrenzungsventil konsultieren Sie bitte die Bestellinformationen für den betreffenden Motor. Soll das Bremsdruckbegrenzungsventil für eine Feldumrüstung oder als Ersatzteil bestellt werden, bitte die Artikelnummer beim Werk erfragen. Befestigungsschrauben in Form von 5/16-18-Sechskantkopfschrauben (es werden 4 benötigt) sowie 2 O-Ringe können vom Werk bezogen werden. Artikelnummer beim Werk erfragen. * Pour commander une soupape de sûreté transversale montée sur un certain moteur, voir les informations de commande pour ce moteur. Pour commander une soupape de sûreté transversale pour la conversion sur place ou comme pièce de rechange, consulter l’usine pour obtenir le numéro de la pièce. Les boulons de montage sont disponibles en tant que vis à tête creuse de 5/16-18 (4 sont requises) ainsi que 2 joints toriques. Consulter l’usine pour obtenir le numéro de la pièce. * Para pedir una válvula de alivio transversal montada en determinado motor, véanse las especificaciones de dicho motor. Para pedir una válvula de alivio transversal para conversión directa o como parte de repuesto, consultar con fábrica sobre el número de parte. Los pernos de montaje vienen en tipo de cabeza hueca hexagonal de 5/16-18 (se necesitan 4) y con 2 sellos toroidales (O rings). Consultar con fábrica sobre el número de parte. Consult factory for other available options, configurations ordering codes and lead times. 023 Nichols Options.indd, js 234 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Installation/Operation Information LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU Nichols™ Fluid Thru-Shafts To insure maximum motor performance and life, use a premium grade hydraulic or engine oil. FLuids with a minimum .125% zinc (or equivalent) anit-wear package should be used. A mineral or synthetic based 10W40 engine oil or hydraulic oil (200 SUS) is recommended. Nichols motor seals come standard in nitrile rubber. If a fluid that is not compatible with nitrile is to be used, flouroelastomer seal material can be specified. • Maximum fluid viscosity - 50 SUS • Recommended fluid operating temperature is -28°C to 82°C (-20°F to 180°F) • Minimum recommended fluid filtration 25 micron with a bet ration of 2. Shaft torque should not exceed 3000 lb-in. Performance Data Performance data shown in this catalog is the result of testing performed using petroleum based fluid at 120°F, 180 SUS. Actual performance will vary with fluid conditions. Lower viscosity will produce lower performance. Run-In For optimum performance and life, a 15 minute run-in period at no load and mid-flow conditions is recommended. Do not subject the system to full load until air has been bled from the hydraulic system and all contaminate particles have been filtered out. Pressure Operating the motor in its intermittent pressure range will shorten the life of the motor and should generally be restricted to 10% or less per minute. The reduced life resulting from continuous operation in the intermittent range may be acceptable in some applications. Consult the factory for details. Inlet Conditions Positive pressure must be available at the motor inlet while it is operating. If an overrunning load causes the motor to rotate faster than the pump can fill it, cavitation will occur. Consult the factory for inlet pressure requirements and speed limitations. Case Drain A check ball system drains the shaft seal to the outlet port regardless of direction of rotation of the shaft. This maintains low pressure on the shaft seal, reducing heat and friction for long seal life. If high pressure exists in the outlet port due to series operation, meter-out circuitry or other causes, the shaft seal can be externally drained to tank for low seal pressure. For continuous operation with outlet pressure above 1000 psi use of the external case drain is recommended for extended seal life. Other Operating Conditions Consult factory before operating at conditions exceeding any ratings or recommendations in this catalog. Installation Recommendations • To avoid contamination do not remove plastic port plugs until fittings are to be installed. • Motor mounting flange must make full contact with equipment mount; do not use the mounting bolts to force the motor pilot into the pilot hole to align the motor. • Pulleys, sprockets, wheels, or couplings should be properly aligned on the shaft to avoid excessive radial or thrust loads. • To avoid damaging the thrust system, do not hammer on the motor or shaft to install or remove couplings, pulleys, sprockets, etc. Shaft Loading The use of 1 inch and 25mm diameter shafts are not recommended when torque loads exceed 3500 lb-in. For 7/8 inch diameter shafts, torque should be limited to 3000 lb-in. Maximum thrust load on the shaft should not exceed 1000 lbs inward or outward. Stainless Steel Shafts Torque, speed, axial, and radial load ratings are reduced by 20% when operating with the stainless steel shaft that is optional on some series of motors. Maximum speed to be limited to 600 RPM. 024 Nichols Installation-Operation.indd, js 235 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors Engineering Data HY13-1590-005/US,EU Hydraulic Formulas Side Load Side loads are imposed upon the shaft of a motor by: QP HPin = 1714 • Driving the load through a pulley or gear • Supporting the weight of a vehicle or other load on the shaft Or both NT HPout = 63025 D Δ Pem T= 2π DN Q = 231 e v Where HP Q P ΔP T D = = = = = = N = em = ev = If the load above requires torque T pound-inches and is driven with a pulley on the motor shaft a with a radius of R inches, the side load imposed on the motor shaft is T/R pounds. If the motor shaft is connected to a sprocket for a chain drive, R is one half the pitch diameter of the sprocket. If an external load with a weight of W pounds is also being supported by the motor shaft above, the total side load on the shaft is: Horsepower Flow, GPM Pressure, PSI Pressure differential across the motor Torque, lb in Motor displacement, cubic inches per revolution Shaft Speed, RPM Mechanical efficiency Volumetric efficiency To Convert Into Into To Convert bars BTU/min BTU/min centigrade centimeters cu. cms. cu. cms. cu. inches cu. inches feet gallons gallons horsepower inches kilograms pounds pound-inches pound-inches radians square inches pounds/sq.in. horsepower kilowatts fahrenheit inches cu. inches liters cu.cms. liters meters cu. inches liters kilowatts millimeters pounds newtons newton-meters daNM degrees sq. cms. Multiply By Divide By 14.5 .02356 .01757 (C°x9/5)+32 .3937 .06102 .001 16.39 .01639 .3048 231 3.785 .7457 25.4 2.205 4.448 .113 .0113 57.3 6.452 (SL)2 = W2 + (T/R)2 Side Load(lb) = W2 + (T/R)2 Warning This Catalog is not a Controlled Document. All Dimensions listed herein are for reference only. Consult a Sales engineer for detailed information. 025 Engineering Data.indd, js 236 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors Engineering Data HY13-1590-005/US,EU Vehicle Propulsion Systems Hydraulic motors are often used to drive off-highway vehicles, either directly or through gear reducers. The power required to propel the vehicle, called "Tractive Effort," is supplied by the hydraulic motor(s). It is normally expressed in pounds and is the sum of the forces below: TE = (RR+GR+F+DP) x 1.1 Where: RR GR F = = = Rolling Resistance Grade Resistance Acceleration Force DP = Drawbar Pull Definitions • Tractive Effort (TE) Tractive effort is the total linear force that a vehicle can exert on the ground. Sometimes called "rim pull," it is the axle torque divided by the distance from the axle to the surface it is traversing. • Rolling Resistance (RR) Rolling resistance is the force in pounds required to propel a vehicle at constant speed over level terrain. It varies with the weight of the vehicle and the type of surface it is traversing. Soft sand, for example, offers more resistance to movement than concrete RR = GVW x R RR Surface Condition Concrete Excellent 0.010 lb. Concrete Good 0.015 lb. Concrete Poor 0.020 lb. Asphalt Good 0.012 lb. Asphalt Fair 0.017 lb. Asphalt Poor 0.022 lb. Macadam Good 0.015 lb. Macadam Fair 0.022 lb. Macadam Poor 0.037 lb. Cobbles Ordinary 0.055 lb. Cobbles Poor 0.085 lb. Grass where: = Rolling Resistance (lbs.) R Value 0.025 lb. Snow 2 In. 0.025 lb. Snow 4 In. 0.037 lb. Dirt Smooth 0.025 lb. Dirt Sandy 0.037 lb. Mud GVW = Gross Vehicle Weight (lbs.) R Surface Type 0.037 to 0.150 lb. Sand Level/Soft 0.060 to 0.150 lb. Sand Dune 0.150 to 0.300 lb. = Rolling Resistance Factor dependent upon type and condition of surface. Typical "R" values are shown in the accompanying table. 025 Engineering Data.indd, js 237 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors Engineering Data HY13-1590-005/US,EU • Grade Resistance (GR) V Grade resistance is the additional force required to move a vehicle up an incline. The grade of a slope is normally expressed as a percentage, and represents the number of feet of rise in 100 feet of length. A slope that rises 10 feet in 100 feet has a grade of 10%. The gradeability of a vehicle is defined as the maximum grade the vehicle can climb. = Change in Velocity (ft. per Second) (Final Velocity - Initial Velocity) GVW = Gross Vehicle Weight (lbs.) T = Time for Velocity Change (Seconds) Note - To obtain velocity in feet per second when MPH is known, Multiply MPH by 1.467. • Drawbar Pull (DP) GR = 0.01 x GVW x G GR = where: GVW = Gross Vehicle Weight (lbs.) G Grade (%) = Drawbar Pull is the force a vehicle can exert on a load in addition to the force required to propel itself. Grade Resistance (lbs.) Actual force to tow or push a load can be calculated based upon Rolling Resistance, Accelerating Force and Grade Resistance of towed or pushed load. The following table gives the approximate relationship between grade in percent and slope in degrees. • Motor Torque The total Tractive effort required to propel a vehicle is the sum of the forces due to Rolling Resistance, Grade Resistance, Acceleration and Drawbar Pull plus 10% for friction and other variables: Grade (Percent) Slope (Degrees) 1% 0° 35' 2% 1° 5% 2° 51' 6% 3° 26' 8% 4° 35' 10% 5° 43' 12% 6° 54' 15% 8° 31' 20% 11° 19' 25% 14° 32% 18° T 60% 31° TE = Tractive Effort 9' TE = (RR + GR + F + DP) x 1.1 When Tractive Effort has been calculated, hydraulic motor torque can be estimated by: T = The force required to accelerate a vehicle from an initial speed V1 (in feet/second) to speed V2 in T seconds is the accelerating force in pounds. If the acceleration is from rest, V1 is zero. V x GVW T x 32.16 GxN where: 3' = Hydraulic Motor Torque (lbs. in.) r = Rolling Radius of Driven Tires (inches) G = Gear Reduction Ratio Between Hydraulic Motors and Driven Wheels ( if none, use a value of 1) N = Number of Driving Motors • Acceleration Force (F) F= TE x r where 025 Engineering Data.indd, js 238 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors Engineering Data HY13-1590-005/US,EU • Slip Torque • Hydraulic Motor Speed Slip torque is the torque at the motor shaft that will cause the wheels or tracks to break traction and skid. It is affected by the weight of the vehicle and the coefficient of friction between the wheels or tracks and the surface. ST = VW x u x r GxN 168 x V x G S = r S = Required Hydraulic Motor Speed (RPM) V = Desired Vehicle Velocity (MPH) G = Gear Reduction Ratio Between Hydraulic Motors and Driven Wheels ( if none, use a value of 1) r = Rolling Radius of driven Tires (inches) where: ST = Hydraulic Motor Slip Torque (lb in) VW = Maximum Weight on Driven Wheel (lb) Including: Allowable Vehicle Overload Dynamic Weight Shift. u = Coefficient of Friction Between Tire and Ground. (A value of 0.6 is used for "normal" tires and an average road surface) r = Rolling Radius of Driven Tires (inches) G = Gear Reduction Ratio Between Hydraulic Motors and Driven Wheel. N = Number of Driving Motors where: The chart below will estimate the wheel RPM -vsvehicle velocity for various rolling radii. MPH -vs- RPM for different Rolling Radii 700 6"R RPM 600 8"R 500 10"R • Rolling Radius 400 12"R 300 The rolling radius should be based on actual application factors such as Plyrating, Rated Load and inflation pressure can result in different values. 14"R 16"R 18"R 20"R 200 100 5 10 15 20 25 MPH 025 Engineering Data.indd, js 239 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA LSHT Torqmotors™ and Nichols™ Motors HY13-1590-005/US,EU 025 Engineering Data.indd, js 240 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA High Speed Hydraulic Motors Catalog HY13-2600-800-001/NA 241 Introduction High Speed Hydraulic Motors High Speed HY13-1590-005/US,EU Features • High Starting Torque typically 90% of running torque. • Smooth Output Torque throughout the entire speed range of the motor. • High Speed Capabilities up to 7500 rpm on some models. • BiDirectional Operation built in checks internally relieve high pressure from the shaft seal. • High Pressure Shaft Seal allows back pressure to 400 PSI without the requirement of Case Drain. • Standard SAE Mounting 2 or 4 bolt mounting flanges, shaft and port dimensions conform to SAE standards. • Long Life & Quiet Operation Precision Gerotor Design results in a motor with extended operating life and noise levels below most other hydraulic motors. • Heavy Duty Bearings capable of withstanding radial and thrust loads. 026 High Speed.indd, js 242 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA High Speed Hydraulic Motors High Speed HY13-1590-005/US,EU Ordering Information XX X XX XX S XX N X Motor Series SAE Port & Mounting/ Valve Mount Product Code Port Size Port Type Shaft Style Drain Shaft Seal Series Drain Port Type Code Type Code M2 SAE 101 (B-Frame) S M4 SAE 82 (A-Frame) Type Code Type N Internal SAE Straight Thread Includes plugged external drain. Shaft Seal Port Size SAE Port & Mounting † Code Ports Mtg. B D† Side Side 2-Bolt 4-Bolt Type B Nitrile V Series Code SAE 10 10 M4 12 12 12 12 M2 16 16 M4 not available. Code Fluorocarbon Shaft Style Cod e † Type 20 † Long, Single-End 30 Short, Single-End 40 Spine, Single-End M4 only available with 20 code shaft. Product Code Series Code M4 M2 015 030 045 060 075 085 127 169 254 339 508 Theoretical Displacement cm 3/rev in 3/rev 2.45 4.91 7.37 9.83 12.29 13.9 20.8 27.7 41.6 55.6 83.2 .15 .30 .45 .60 .75 .85 1.27 1.69 2.54 3.39 5.08 THERMAL SHOCK WARNING: IF THE MOTOR IS TO OPERATED BY FLUID WHICH IS 80°F OR MORE ABOVE THE OPERATING ENVIRONMENT TEMPERATURE, CONSULT FACTORY. 026 High Speed.indd, js 243 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA High Speed Hydraulic Motors High Speed HY13-1590-005/US,EU Introduction Applications Parker motors serve our customers worldwide in many industries and in many applications. Typical applications include: Fan Drives High speed capabilities means increased cooling capacity. Rugged bearing design allows the fan to be mounted directly on the motor shaft. Swing Drives High starting torque and smooth output torque throughout the motor’s speed range means optimum control. Starting and running torque comparison between Parker Gerotor and typical Spur Gear and Vane Motors. Vibratory Drives Rugged design, high speed capabilities, and optional cross port relief valve means maximum life for vibratory drives. Wheel Drives High speed capabilities and high starting torque means faster road speeds and increased productivity. Winch Drives Smooth output torque throughout the speed range, high speed capabilities, and high starting torque means increased control, greater productivity. 026 High Speed.indd, js 244 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA High Speed Hydraulic Motors M4 Series HY13-1590-005/US,EU Technical Information Performance Data & Mounting Data M4-015 7 6 E W LO 2000 PSI F 30 3 20 1000 2 PSI 10 0 2000 4000 6000 OW 3000 PSI 4 50 2 1000 PSI 1 25 7500 0 1 1000 TORQUE 300 10 O FL 2000 PSI I P I PS 00 20 PSI 0 150 250 8 6 100 4 1000 PSI 50 0 1000 2000 3000 TORQUE (Lbs. In.) W 200 30 12 SI FLOW (GPM) 00 0 Displacement I (in3/rev) (.15) (.30) (.45) (.60) (.75) Weight 7.3 7.7 8.2 8.6 9.1 Kg Kg Kg Kg Kg (16 (17 (18 (19 (20 lb) lb) lb) lb) lb) F 0 30 PS 0 00 2 200 10 I PS I PS 0 8 150 100 2 50 3750 0 6 1000 PSI 4 2 1000 2000 3000 SPEED (RPM) Speed cm3/rev 2.45 4.91 7.37 9.83 12.29 W LO 2000 PS SPEED (RPM) Unit Unit Unit Unit Unit 14 3000 PSI TORQUE 250 TORQUE (Lbs. In.) 350 12 3000 PSI 5000 M4-075 300 015 030 045 060 075 3000 SPEED (RPM) M4-060 Unit Unit Unit Unit Unit 3 2000 PSI SPEED (RPM) 015 030 045 060 075 TORQUE 125 100 6 5 20 150 4 FL 40 TORQUE (Lbs. In.) I PS 00 PSI 0 0 20 PSI 0 30 00 5 FLOW (GPM) TORQUE (Lbs. In.) 50 FLOW (GPM) TORQU FLOW (GPM) 3000 PSI PS 3 I 00 0 0 PS PS I I 60 M4-030 Recommended 015 Unit 030 Unit 045 Unit 060 Unit 075 Unit Performance Curves: Range 75 to 7500 50 to 5000 50 to 5000 36 to 3600 30 to 3000 rpm rpm rpm rpm rpm Minimum speeds indicated are based on constant load. For speeds outside of the recommended range, consult the factory. Data based on: Oil: 65 cst (300 SSU) Mobil DTE-26 Temp: 38°C (100°F) Pressure † ‡ † ‡ Continuous: Intermittent, Max: Transient, Max: 2000 PSI 2400 PSI 3000 PSI Intermittent conditions are to be less than 10% of each minute. Transient conditions are to be less than 1% of every minute. 026 High Speed.indd, js 245 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA High Speed Hydraulic Motors M4 Series HY13-1590-005/US,EU Technical Information Performance Data & Mounting Data M4-045 300 12 30 00 PS I 250 200 3000 PSI 2 TORQUE I PS I PS 0 10 8 W O FL 150 6 2000 PSI 100 4 1000 PSI 50 0 FLOW (GPM) TORQUE (Lbs. In.) 0 00 Dimensions are shown in millimeters. Dimensions within ( ) are in inches. 1000 2000 3000 Code A B 015 143.26 (5.64) 107.44 (4.23) 030 149.61 (5.89) 113.79 (4.48) 045 156.21 (6.15) 120.14 (4.73) 060 162.31 (6.39) 126.49 (4.98) 075 168.66 (6.64) 132.84 (5.23) 2 4000 5000 SPEED (RPM) MOUNTING DATA 026 High Speed.indd, js 246 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA High Speed Hydraulic Motors M2 Series HY13-1590-005/US,EU Technical Information Performance Data M2-085 TORQUE N•m Lb.In. FLOW (US) GPM I/min. 48 80 400 3000 PSI 68 30 3000 PSI 30 20 00 P 00 S P I 0 PS SI I TORQUE 60 70 40 300 FLOW (US) GPM I/min. 600 20 TORQUE M2-127 TORQUE N•m Lb.In. 100 500 60 25 50 15 80 400 40 300 10 200 30 20 00 0 P 0 0 P SI PS S I I 40 FL 2000 PSI 20 2000 PSI 50 OW 30 W O FL 30 200 5 0 1000 2000 3000 4000 1000 PSI 10 100 5 0 M2-254 2000 1000 FLOW (US) GPM I/min. M2-339 TORQUE N•m Lb.In. 180 35 4000 160 FLOW (US) GPM I/min. 1600 40 TORQUE 3000 PSI 120 140 1200 3000 SPEED (RPM) 160 1400 20 0 0 5000 SPEED (RPM) TORQUE N•m Lb.In. 40 20 0 0 10 20 1000 PSI 100 10 140 1400 35 1200 30 30 TORQUE 3000 PSI 120 120 140 100 25 100 800 2000 PSI 120 20 100 2000 PSI 1000 80 25 30 0 20 0 P 00 SI 0 PS PS I I 30 20 00 00 PS 0 P PS I SI I 1000 100 80 80 FL FL 60 600 15 60 400 10 1000 PSI 40 200 5 0 1000 2000 10 200 5 0 0 0 400 20 20 3000 40 20 0 0 SPEED (RPM) 60 1000 PSI 40 40 80 O OW 60 15 20 W 800 600 20 60 30 20 10 15 500 1000 1500 2000 SPEED (RPM) 026 High Speed.indd, js 247 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA High Speed Hydraulic Motors M2 Series HY13-1590-005/US,EU Technical Information Performance Data M2-169 TORQUE N•m Lb.In. 750 120 TORQUE 3000 PSI Displacement FLOW (US) GPM I/min. 085 127 169 254 339 508 30 80 100 70 625 25 60 30 2 0 00 0 P 0 0 P SI PS S I I 20 50 30 15 OW 375 Pressure Continuous: M2-508 1000 PSI All other Units 2000 PSI 60 FL 40 250 10 1000 PSI † Intermittent, Max: M2-508 1400 PSI All other Units 2400 PSI ‡ Transient, Max: M2-508 1700 PSI All other Units 3000 PSI 40 20 125 5 500 PSI 20 10 0 0 1000 0 (in3/rev) (0.85) (1.27) (1.69) (2.54) (3.39) (5.08) 80 2000 PSI 500 Unit Unit Unit Unit Unit Unit cm3/rev 13.9 20.8 27.7 41.6 55.6 83.2 2000 † 3000 ‡ SPEED (RPM) Intermittent conditions are to be less than 10% of each minute. Transient conditions are to be less than 1% of every minute. Speed Recommended Range M2-508 TORQUE N•m Lb.In. 085 127 169 254 339 508 FLOW (US) GPM I/min. 140 200 1750 35 1500 30 1250 25 175 120 100 TORQUE 1 10 500 0 0 P 0 P PSI SI SI OW 1000 PSI 75 50 20 FL 750 to to to to to to 5000 4000 3600 3000 2000 1500 rpm rpm rpm rpm rpm rpm 1500 PSI 1000 100 50 40 36 30 20 15 Minimum speeds indicated are based on constant load. For speeds outside of the recommended range, consult the factory. 150 125 Unit Unit Unit Unit Unit Unit 500 15 80 Weight 085 127 169 254 339 508 60 10 40 5 20 Unit Unit Unit Unit Unit Unit 15.4 16.3 17.2 18.6 20.4 24.0 Kg Kg Kg Kg Kg Kg (34 (36 (38 (41 (45 (52 lb) lb) lb) lb) lb) lb) 500 PSI 25 250 0 Performance Curves: Data based on: Oil: 65 cst (300 SSU) Mobil DTE-26 Temp: 38°C (100°F) * Stall torque band is application dependent, consult factory. 0 0 500 1000 1500 SPEED (RPM) 026 High Speed.indd, js 248 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information High Speed Hydraulic Motors M2 Series HY13-1590-005/US,EU Mounting Data Dimensions are shown in millimeters. Dimensions within ( ) are in inches. Code Dimension “A” 085 158.8 (6.25) 127 165.1 (6.50) 169 171.5 (6.75) 254 184.2 (7.25) 339 196.9 (7.75) 508 222.3 (8.75) FLANGE OPTION SAE 101-4 Mounting DIMENSIONS PORT LOCATION DRAIN PORT 1. The shaft will rotate in the direction of this “ARROWHEAD” when Port “A” is the inlet “IN” or pressure port. 2. With Port “B” as the inlet “IN” or pressure port, the shaft will rotate in the direction of this “ARROWHEAD”. Drain Port Will Be: 1. No. 6-SAE for the SAE ported motors. 026 High Speed.indd, js 249 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information High Speed Hydraulic Motors M2 Series HY13-1590-005/US,EU Mounting Data SHAFT OPTIONS 026 High Speed.indd, js 250 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Technical Information High Speed Hydraulic Motors High Speed HY13-1590-005/US,EU Operating Pressures Dimensions Continuous: M2-508 1000 PSI All other Units 2000 PSI Intermittent, Max: M2-508 1400 PSI All other Units 2400 PSI Transient, Max: M2-508 1700 PSI All other Units 3000 PSI Published dimensions are nominal. Allowances should be made for dimensional variations of cast parts. Installation Requirements Pulleys, sprockets, and belts should be properly aligned on the shaft; and fan blades should be properly sized to prevent excessive thrust loads. Shaft Seal The standard Nitrile shaft seal is adequate for most applications. For applications which involve shaft speeds above 2500 rpm or synthetic fluids, the operational Viton shaft seal should be specified. Filtration 25 micron or less Fluids To insure ultimate component life, use premium quality hydraulic oils. Fluids with effective quantities of anti-wear agents or additives, (such as Mobil Oil DTE-26), are highly recommended. Static Seals All the o-rings included within the motor and the shaft dust seal are Nitrile. They may be used with all types of hydraulic fluids. However, since these seals swell after exposure to ester base synthetic fluids, they should be replaced if the motor is repaired. Viscosity Maximum Minimum 1000 centistokes 5000 SSU 13.5 centistokes 70 SSU Motor Precaution A hydraulic motor is not designed to hold a suspended load. Therefore, if the application requires a locked position, a mechanical holding device (such as a brake) must be employed. Consult factory for availability. Recommended Temperature Range -40°C (-40°F) to 82°C (180°F) For different operating conditions, consult the factory. Case Drain Precaution If outlet port exceeds 400 PSI, the external case drain should be used with no more than 400 PSI back pressure. 026 High Speed.indd, js 251 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA HY13-1590-005/US,EU 027 Offer of Sale-Sales Offices.indd, js 252 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Offer of Sale HY13-1590-005/US,EU The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized distributors are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiaries and its authorized distributors. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order for any such items, when communicated to Parker Hannifin Corporation, its subsidiary or an authorized distributor (“Seller”) verbally or in writing, shall constitute acceptance of this offer. 1. Terms and Conditions of Sale: All descriptions, quotations, proposals, offers, acknowledgments, acceptances and sales of Seller’s products are subject to and shall be governed exclusively by the terms and conditions stated herein. Buyer’s acceptance of any offer to sell is limited to these terms and conditions. Any terms or conditions in addition to, or inconsistent with those stated herein, proposed by Buyer in any acceptance of an offer by Seller, are hereby objected to. No such additional, different or inconsistent terms and conditions shall become part of the contract between Buyer and Seller unless expressly accepted in writing by Seller. Seller’s acceptance of any offer to purchase by Buyer is expressly conditional upon Buyer’s assent to all the terms and conditions stated herein, including any terms in addition to, or inconsistent with those contained in Buyer’s offer, Acceptance of Seller’s products shall in all events constitute such assent. 2. Payment: Payment shall be made by Buyer net 30 days from the date of delivery of the items purchased hereunder. Amounts not timely paid shall bear interest at the maximum rate permitted by law for each month or portion thereof that the Buyer is late in making payment. Any claims by Buyer for omissions or shortages in a shipment shall be waived unless Seller receives notice thereof within 30 days after Buyer’s receipt of the shipment. 3. Delivery: Unless otherwise provided on the face hereof, delivery shall be made F.O.B. Seller’s plant. Regardless of the method of delivery, however, risk of loss shall pass to Buyer upon Seller’s delivery to a carrier. Any delivery dates shown are approximate only and Seller shall have no liability for any delays in delivery. 4. Warranty: Seller warrants that the items sold hereunder shall be free from defects in material or workmanship for a period of 18 months from date of shipment from Parker Hannifin Corporation. THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO ITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHER WARRANTY, GUARANTEE, OR REPRESENTATION OF ANY KIND WHATSOEVER. ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR PURPOSE, WHETHER EXPRESS, IMPLIED, OR ARISING BY OPERATION OF LAW, TRADE USAGE, OR COURSE OF DEALING ARE HEREBY DISCLAIMED. NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR PARTIALLY, TO BUYER’S DESIGNS OR SPECIFICATIONS. 5. Limitation Of Remedy: SELLER’S LIABILITY ARISING FROM OR IN ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACT SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE ITEMS SOLD OR REFUND OF THE PURCHASE PRICE PAID BY BUYER, AT SELLER’S SOLE OPTION. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING FROM OR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR ITEMS SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACH OF CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TO WARN OR STRICT LIABILITY. 6. Changes, Reschedules and Cancellations: Buyer may request to modify the designs or specifications for the items sold hereunder as well as the quantities and delivery dates thereof, or may request to cancel all or part of this order, however, no such requested modification or cancellation shall become part of the contract between Buyer and Seller unless accepted by Seller in a written amendment to this Agreement. Acceptance of any such requested modification or cancellation shall be at Seller’s discretion, and shall be upon such terms and conditions as Seller may require. 7. Special Tooling: A tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired to manufacture items sold pursuant to this contract. Such special tooling shall be and remain Seller’s property notwithstanding payment of any charges by Buyer. In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in the manufacture of the items sold hereunder, even if such apparatus has been specially converted or adapted for such manufacture and notwithstanding any charges paid by Buyer. Unless otherwise agreed, Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time. 8. Buyer’s Property: Any designs, tools, patterns, materials, drawings, confidential information or equipment furnished by Buyer or any other items which become Buyer’s property, may be considered obsolete and may be destroyed by Seller after two (2) consecutive years have elapsed without Buyer placing an order for the items which are manufactured using such property, Seller shall not be responsible for any loss or damage to such property while it is in Seller’s possession or control. 9. Taxes: Unless otherwise indicated on the face hereof, all prices and charges are exclusive of excise, sales, use, property, occupational or like taxes which may be imposed by any taxing authority upon the manufacture, sale or delivery of the items sold hereunder. If any such taxes must be paid by Seller or if Seller is liable for the collection of such tax, the amount thereof shall be in addition to the amounts for the items sold. Buyer agrees to pay all such taxes or to reimburse Seller therefore upon receipt of its invoice. If Buyer claims exemption from any sales, use or other tax imposed by any taxing authority, Buyer shall save Seller harmless from and against any such tax, together with any interest or penalties thereon which may be assessed if the items are held to be taxable. 10. Indemnity For Infringement of Intellectual Property Rights: Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this Part 10. Seller will defend and indemnify Buyer against allegations of infringement of U.S. Patents, U.S. Trademarks, copyrights, trade dress and trade secrets (hereinafter ‘Intellectual Property Rights’). Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an action brought against Buyer based on an allegation that an item sold pursuant to this contract infringes the Intellectual Property Rights of a third party. Seller’s obligation to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten (10) days after Buyer becomes aware of such allegations of infringement, and Seller having sole control over the defense of any allegations or actions including all negotiations for settlement or compromise. If an item sold hereunder is subject to a claim that it infringes the Intellectual Property Rights of a third party, Seller may, at its sole expense and option, procure for Buyer the right to continue using said item, replace or modify said item so as to make it noninfringing, or offer to accept return of said item and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information provided by Buyer, or directed to items delivered hereunder for which the designs are specified in whole or part by Buyer, or infringements resulting from the modification, combination or use in a system of any item sold hereunder. The foregoing provisions of this Part 10 shall constitute Seller’s sole and exclusive liability and Buyer’s sole and exclusive remedy for infringement of Intellectual Property Rights. If a claim is based on information provided by Buyer or if the design for an item delivered hereunder is specified in whole or in part by Buyer, Buyer shall defend and indemnify Seller for all costs, expenses or judgments resulting from any claim that such item infringes any patent, trademark, copyright, trade dress, trade secret or any similar right. 11. Force Majeure: Seller does not assume the risk of and shall not be liable for delay or failure to perform any of Seller’s obligations by reason of circumstances beyond the reasonable control of Seller (hereinafter ‘Events of Force Majeure’). Events of Force Majeure shall include without limitation, accidents, acts of God, strikes or labor disputes, acts, laws, rules or regulations of any government or government agency, fires, floods, delays or failures in delivery of carriers or suppliers, shortages of materials and any other cause beyond Seller’s control. 12. Entire Agreement/Governing Law: The terms and conditions set forth herein, together with any amendments, modifications and any different terms or conditions expressly accepted by Seller in writing, shall constitute the entire Agreement concerning the items sold, and there are no oral or other representations or agreements which pertain thereto. This Agreement shall be governed in all respects by the law of the State of Ohio. No actions arising out of the sale of the items sold hereunder or this Agreement may be brought by either party more than two (2) years after the cause of action accrues. 9/91-P 027 Offer of Sale-Sales Offices.indd, js 253 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Parker Hydraulics International Sales Offices USA Eastern Region 23 Vreeland Road, Suite 101 Florham Park, NJ 07932 Tel: 973-966-5500 Fax: 973-966-5525 Chicago Region 500 South Wolf Road Des Plaines, IL 60016 Tel: 847-294-2628 Fax: 847-294-2630 Great Lakes Region 3700 Embassy Parkway, Suite 260 Fairlawn, OH 44333 Tel: 330-670-2680 Fax: 330-670-2681 Pacific Region 16655 Noyes Avenue Irvine, CA 92714 Tel: 949-660-7033 Fax: 949-852-9577 Southern Region 1225 Old Alpharetta Road, Suite 290 Alpharetta, GA 30005 Tel: 770-619-9767 Fax: 770-619-9806 Mobile Systems Division 595 Schelter Road Lincolnshire, IL 60069 Tel: 847-821-1500 Fax: 847-821-9597 Parker Europe A Canada 530 Kipling Avenue Toronto, Ontario M8Z 5E6 Tel: 416-255-7371 Fax: 416-255-2107 MEX Mexico Eje Uno Norte No. 100 Parque Indusrial Toluca 2000 Toluca, Edo. de Mexico C.P. 50100 Tel: 7-275-42-00 Fax: 7-279-93-08 D Germany Austria Parker Hannifin GmbH Buro Wien Muhlstrasse 2 A-4614 Marchtrenk Bei Wels Tel: 43 (0) 7242 569 21 Fax: 43 (0) 7242 569 21 20 Parker Hannifin GmbH Werk Kaarst Gutenbergstrasse 38 D-41564 Kaarst, Germany Tel: 49-2131-51 30 Fax: 49-2131-51 32 30 H B Hungary Belgium Parker Hannifin S.A.-N.V. Parc Industriel Sud Zone 2, 15, rue du Bosquet B-1400 Nivelles Tel: 32 (0) 67 280 900 Fax: 32 (0) 67 280 999 CZ Parker Hannifin Vezer ut 56-158 H-1148 Budapest Tel: 36 1 25 28 137 Fax: 36 1 25 28 129 I Italy Czech Republic Parker Hannifin Dopravákú 723 CZ-184 00 Prague 8 Tel: +42 (0) 2 830 85 221 Fax: +42 (0) 2 830 85 360 DK Parker Hannifin SpA Via Privata Archimede 1 1-20094 Corsico, Milano, Italy Tel: 39-2-45 19 21 Fax: 39-2-4 47 93 40 NL The Netherlands Denmark Parker Hannifin Denmark A/S Industrigrenen 11 DK-2635 Ishoj, Denmark Tel: 45-43-54 11 33 Fax: 45-42-73 31 07 Parker Hannifin B.V. Edisonstraat 1 7575 AH Oldenzaal Tel: 31-541-585000 Fax: 31-541-585459 N GB Norway England CAN HY13-1590-005/US,EU Parker Hannifin plc 66 Wakefield Road Ossett, W. Yorks WF5 9JS Tel: 44 (0) 1924 282200 Fax: 44 (0) 1924 282299 Parker Hannifin A/S Berghagan, Langhus P O Box 3008 N-1402 Ski Tel: 47 64 91 10 00 Fax: 47 64 91 10 90 PL Poland FIN Finland Parker Hannifin Oy Ylastontie 16 FIN-01510 Vantaa, Finland Tel: 358-0-476 731 Fax: 358-0-4767 3200 Parker Hannifin ul. Parowcowa 8B PL 02-445 Warsaw, Poland Tel: 48 22 8634942 Fax: 48 22 8634944 E Spain F France Parker Hannifin SA 142, rue de la Foret 74130 Contamine-sur-Arve, France Tel: 33-50-25-80-25 Fax: 33-50-03-67-37 Parker Hannifin Espana S.A. P.I. Las Monjas CI. Estaciones 8 E-28850 Torrejon de Ardoz Madrid, Spain Tel: 34-1-6757300 Fax: 34-1-6757711 9/1/96 027 Offer of Sale-Sales Offices.indd, js 254 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Parker Hydraulics International Sales Offices S Sweden Parker Hannifin Sweden AB Fagerstagatan 51 Box 8314 S-16308 Spanga, Sweden Tel: 46 8 5979 5000 Fax: 46 8 5979 5110 IND HY13-1590-005/US,EU RC Parker Hannifin India Plot EL 26 MIDC Mahape Navi Mumbay, India Tel: (91)(22) 790 7081 Fax: (91)(22) 790 7080 Taiwan Parker Hannifin Taiwan Co., Ltd. 8F-1, No. 102 Sung Lung Road Taipei, Taiwan, ROC Tel: 886 2 8787 3780 Fax: 886 2 8787 3782 ROK Asia Pacific Group AUS Australia Parker Hannifin Australia 9 Carrington Road Castle Hill, NSW 2154, Australia Tel: 61-2-634-7777 Fax: 61-2-842-5111 Latin American Group Korea Parker Hannifin Asia Pacific Co. Ltd. 237-4, Hagal-ri, Kiheung-eup Yongin-City, Kyunggi-do, Korea Yongin-city, Kyunggi-do,, 449-900 Tel: 82 331 280 3000 Fax: 82 331 281 9018 MAL USA Pan American Division Parker Hannifin Corporation 7400 N.W. 19th St., Suite A Miami, FL 33126 USA Tel: (305) 470-8800 Fax: (305) 470-8808 Malaysia CHN China Parker Hannifin Hong Kong Ltd. Suite B9-B11, 21/F, Hanwei Plaza No. 7 Guanghua Rd., Chaoyang District Beijing 100004 China Tel: 86 10 6561 0520-5 Fax: 861 10 6561 0526-7 Parker Hannifin Malaysia Suite E-08-16, Block E Plaza Mont’Kiara 2, Jalan 1/70C, Mont’Kiara 50480 Kuala Lumpur, Malaysia Tel: 60 3 6203 4482 Fax: 60 3 6203 4457 RA Argentina Parker Hannifin Argentina S.A.I.C. Stephenson 2711, esq. Costa Rica 1667 Tortuguitas Malvinas Argentinas Tel: (54) (11) 4752-4129 Fax: (54)(11) 4752-3704 NZ Parker Hannifin Hong Kong Ltd. Shanghai Office Room 703, Dynasty Business Ctr. No. 457 North Wu Lu Mu Qi Road Shanghai, 200040, China Tel: 86-21-624-99755 Fax: 86-21-624-94657 HK BR New Zealand Parker Hannifin (N.Z.) Ltd. 103 Harris Road, East Tamaki Private Bag 14906, Panmure Auckland, New Zealand Tel: 64-9-273-8944 Fax: 64-9-273-8943 J Hong Kong Japan Parker Hannifin Hong Kong Ltd. 8/F, Kin Yip Plaza, 9 Cheung Yee Street, Cheung Sha Wan, Kowloon, Hong Kong New Territory, Hong Kong Tel: 852-2428-8008 Fax: 852-2480-4256 Parker Hannifin Japan, Ltd. Shirokanedai Building 2nd Floor 3-2-10, Shirokanedai Minato-ku Tokyo 108-0071 Japan Tel: 81-3-6408-3900 Fax: 81-3-5449-7201 SGP Brazil Parker Hannifin Schrader Bellows Variante Lucas Nogueira Garcez 2181 CX.P.148 12300-000 Jacarei S.P., Brazil Tel: 55-123-517000 Fax: 55-123-545266 V Venezuela Parker Hannifin Venezuela S.A. Edf. Draza PB. Esq. Calle Miraima Con. Av. Principal Boleita Norte Caracas, Venezuela Tel: 58-2-2385422 Fax: 58-2-2392272 Singapore Parker Hannifin Singapore Pte. Ltd. No. 11 4th Chin Bee Road Jurong Town, Singapore 619702 Republic of Singapore Tel: 65-261-5233 Fax: 65-265-5125 Africa ZA South Africa Parker Hannifin Africa Pty. Parker Place 10 Berne Avenue Aeroport Kempton Park, South Africa Tel: 27 11 3927280 Fax: 27 11 3927213 06/28/01 027 Offer of Sale-Sales Offices.indd, js 255 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA HY13-1590-005/US,EU 027 Offer of Sale-Sales Offices.indd, js 256 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA HY13-1590-005/US,EU 027 Offer of Sale-Sales Offices.indd, js 257 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA HY13-1590-005/US,EU 027 Offer of Sale-Sales Offices.indd, js 258 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Parker Hannifin Corporation 6035 Parkland Blvd. Cleveland, Ohio 44124-4141 Telephone: (216) 896-3000 Fax: (216) 896-4000 www.parker.com About Parker Hannifin Corporation Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 500 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that control motion in some 1,000 industrial and aerospace markets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic, and electromechanical motion-control solutions. Our Company has the largest distribution network in its field, with over 7,500 distributors serving nearly 400,000 customers worldwide. WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. Offer of Sale The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated on the separate page of this document entitled “Offer of Sale”. © 2000, 2001, 2003, 2004, 2006 Parker Hannifin Corporation Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee, USA Parker Hannifin Corporation Parker’s Charter To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve profitable growth through premier customer service. Product Information North American customers seeking product information, the location of a nearby distributor, or repair services will receive prompt attention by calling the Parker Product Information Center at our toll-free number: 1-800-C-PARKER (1-800-272-7537). In Europe, call 00800-C-PARKER-H (00800-2727-5374). The Aerospace Group is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high-technology markets, while achieving growth through premier customer service. The Climate & Industrial Controls Group designs, manufactures and markets systemcontrol and fluid-handling components and systems to refrigeration, air-conditioning and industrial customers worldwide. The Fluid Connectors Group designs, manufactures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems. The Seal Group designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction. The Hydraulics Group designs, produces and markets a full spectrum of hydraulic components and systems to builders and users of industrial and mobile machinery and equipment. The Filtration Group designs, manufactures and markets quality filtration and clarification products, providing customers with the best value, quality, technical support, and global availability. The Automation Group is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide. The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical flow components for worldwide process instrumentation, ultra-highpurity, medical and analytical applications. LSHT Torqmotors™ and Nichols™ Motors Catalog No. HY13-1590-005/US,EU LSHT Torqmotors™ and Nichols™ Motors Parker Hannifin Corporation Hydraulic Pump/Motor Division 2745 Snapps Ferry Road Greeneville, TN 37745 USA Tel: (423) 639-8151 Fax: (423) 787-2418 www.parker.com/pumpmotor HY13-1590-005/US,EU © Copyright 2006 Parker Hannifin Corporation All rights reserved. HGF Series Hydrostatic Steering Unit Catalog HY13-1560-002/US Parker Hannifin Corporation Catalog HY13-1560-002/US Hydraulic Pump/Motor Division 5000, 02/03, EcoQuest Printing 2745 Snapps Ferry Rd. Greeneville, TN 37745 USA Tel: (423) 639-8151 Fax: (423) 787-2418 Web Site: www.parker.com/pumpmotor Parker Hannifin Corporation 6035 Parkland Blvd. Cleveland, Ohio 44124-4141 Telephone: (216) 896-3000 Fax: (216) 896-4000 www.parker.com About Parker Hannifin Corporation Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 500 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that control motion in some 1,000 industrial and aerospace markets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic, and electromechanical motion-control solutions. Our Company has the largest distribution network in its field, with over 7,500 distributors serving nearly 400,000 customers worldwide. WARNING Parker Hannifin Corporation Parker’s Charter To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve profitable growth through premier customer service. Product Information North American customers seeking product information, the location of a nearby distributor, or repair services will receive prompt attention by calling the Parker Product Information Center at our toll-free number: 1-800-CPARKER (1-800-272-7537). In Europe, call 00800-C-PARKER-H (00800-2727-5374). The Aerospace Group is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high-technology markets, while achieving growth through premier customer service. The Climate & Industrial Controls Group designs, manufactures and markets system-control and fluid-handling components and systems to refrigeration, air-conditioning and industrial customers worldwide. The Fluid Connectors Group designs, manufactures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems. The Seal Group designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction. The Hydraulics Group designs, produces and markets a full spectrum of hydraulic components and systems to builders and users of industrial and mobile machinery and equipment. The Filtration Group designs, manufactures and markets quality filtration and clarification products, providing customers with the best value, quality, technical support, and global availability. The Automation Group is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide. The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical flow components for worldwide process instrumentation, ultra-high-purity, medical and analytical applications. FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. Offer of Sale The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the "Offer of Sale". Copyright 2003, Parker Hannifin Corporation, All Rights Reserved Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee US Catalog HY13-1560-002/US Introduction Hydrostatic Steering Unit HGF Series Hydraguide™ brand hydrostatic steering units were developed to meet the requirements of a broad range of off-highway applications. The HGF series is designed for light duty applications such as lawn and garden equipment, small agricultural equipment, small off-highway vehicles and material handling equipment. HGF Series Features • Compact Size—The compact size of the HGF permits mounting in tight spaces to add overall machine design flexibility. • Full-Pressure Shaft Seal—The Parker full pressure input shaft seal is able to withstand full system back pressure up to the pressure rating of the Hydraguide. This enables operation of auxiliary hydraulic functions downstream of steering. • Pressure Dams—Pressure dams provide a barrier of pressurized system oil between metered oil and return. Pressure dam valving provides more precise steering due to the reduction of leakage oil from the metering element. • Needle Thrust Bearing—The needle trust bearing reduces input torque required to steer, resulting in lower steering efforts. • SAE #6 Female O-Ring Ports Standard. • Integral Mounting Studs—Integral mounting bolts minimize hardware cost and simplify installation, resulting in fewer service parts. • Manual Emergency Steering—A ball check valve allows manual steering in emergencies when pump flow is interrupted. If the vehicle is large enough to require more that 100 ft.-lb. steering wheel torque in the manual mode, another means of emergency steering is recommended. • Integral Relief Available—Five pressure settings from 500 to 1740 psi. Preset to protect steering unit from excessive system pressure. 1560-002.P65, pm 1 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit HGF Series Catalog HY13-1560-002/US Model Number Explanation Hydraguide™ Series XX 08 10 12 16 20 24 X 2 4 HGF XX XXX X 0 1* Type Nonreversing Nonreversing (low noise) 2 Open Center Reversing 6 Power Beyond Nonreversing 3 Power Beyond Reversing 4 Closed Center Nonreversing 7 Closed Center Reversing * Only available with port option 2 HGF Displacement in3/rev cm3/rev 3.30 54.1 4.13 67.7 4.95 81.1 6.60 108.2 8.25 135.2 9.90 162.3 Porting Female #6 SAE O-Ring Female #6 SAE O-Ring Side Port X 2 4 7 6 8 System Open Center Open Center Relief Option No Relief 921 psi (64 Bar) 1200 psi (83 Bar) 1560 psi (108 Bar) 1740 psi (120 Bar) P R Example: HGF08220 signifies HGF Hydraguide series unit with 3.30 in3/rev displacement, open center, nonreversing with female #6 SAE O-Ring ports. 1560-002.P65, pm 2 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit HGF Series Catalog HY13-1560-002/US Specifications HGF Hydraguide™ Series 16 20 24 3.30 54.1 4.13 67.7 4.95 81.1 6.60 108.2 8.25 135.2 9.9 162.3 Operating Pressure (psi) (Bar) Maximum 1800 125 1800 125 1800 125 1800 125 1800 125 1800 125 Operating Temperature (°F) (°C) Maximum 200 93.3 200 93.3 200 93.3 200 93.3 200 93.3 200 93.3 Continuous Rated 8 30.3 8 30.3 8 30.3 8 30.3 8 30.3 8 30.3 Recommended2 (120 rpm) 1.71 6.47 2.15 8.14 2.57 9.73 3.43 12.98 4.29 16.24 5.14 19.45 8.8 3.99 9.04 4.10 9.28 4.21 9.77 4.43 10.25 4.65 10.75 4.88 “A” Dimensions3 (in) (mm) 4.37 111.0 4.50 114.2 4.62 117.3 4.87 123.6 5.12 130.0 5.42 137.5 “B” Dimensions (in) (mm) 5.3 134.6 5.4 137.1 5.6 142.2 5.8 147.3 6.1 154.9 6.4 162.6 English dimensions are control values; metric values are conversions. For two handwheel turns per second. Length from mounting face to end of Hydraguide end. Fluid/Filtration Automatic transmission fluid (ATF) or contact your Parker Sales Engineer for other fluid recommendations. HGF Delta P -vs- Flow at 130° F (54.5° C) (113 SUS) 4 (PSI) Use 20-50 micrometer nominal filtration. 8 11 Inlet Flow (LPM) 15 18 23 26 30 34 38 120 8.3 100 6.9 80 5.5 60 4.1 40 2.8 20 1.4 1 2 3 4 5 6 7 8 9 10 Inlet Flow (GPM) 1560-002.P65, pm 3 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA (BAR) 3 12 English Metric Weight (lbs) (kg) 2 10 Displacement (in3/rev) (cm3/rev) Flow (gpm) (liters/min) 1 08 Hydrostatic Steering Unit HGF Series Catalog HY13-1560-002/US Dimensions HGF Open Center HGF Power Beyond (HGFXX2X0) (HGFXX2X6) "A" LENGTH 3.05 (77.5) Max .67 Max 1.00 (25.4) OUT OUT LT 45˚ TYP AUX LT RT RT IN IN 72˚ TYP (4) 5/16-24 UNF-2A Thread Studs Equally Spaced & Located On A Ø3.250 (82.55) Circle 9/16-18 Straight Thread SAE #6 Female O-Ring Ports on a Ø1.66 (42.16) Circle 3.05 (77.3) MAX TYP “A” Dimensions Series (in) (mm) 08 4.16 105.7 10 4.28 108.7 12 4.41 112.0 16 4.66 118.4 20 4.91 124.7 24 5.16 131.1 HGF Open Center Sideport (HGFXX4X0) Dimension “B” 2.76 (70.1) 45˚ TYP LT IN RT AUX OUT 3.17 (80.5) Max 1.00 (25.4) 1.25 (31.8) .62 (15.7) (4) 5/16-24 UNF-2A Thread Studs. Equally Spaced & Located on a Ø3.250 (82.55) Circle .56 (14.2) 9/16-18 Straight Thread O-Ring Ports “B” Dimensions Series (in) (mm) 08 5.38 136.6 10 5.50 139.7 12 5.63 143.0 16 5.88 149.3 20 6.13 155.7 24 6.38 162.1 Note: 1. All dimensions are for reference only. 2. Add .50 in (12.7 mm) for integral relief. (Porting option 2 only) 3. Reversing units shall be used with balanced area cylinders. Adapter Fittings 411085A1 411090A1 Straight Thread SAE #6 O-Ring Parker Seal-Lok 9/16 x 18 Straight Thread SAE #6 O-Ring Male JIC 37o Flare 1560-002.P65, pm 4 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit HGF Series Catalog HY13-1560-002/US Dimensions HGF Power Beyond Sideport (HGFXX4X6) Dimension “B” 2.76 (70.1) (4) 5/16-24 UNF-2A Thread Studs Equally Spaced & Located on a Ø3.250 (82.55) Circle 1.25 (31.8) .51 (13.0) LT IN RT AUX OUT .62 (15.7) 45˚ TYP 3.17 (80.5) Max 1.00 (25.4) .56 (14.2) Note: 1. All dimensions are for reference only. 2. Add .50 in (12.7 mm) for integral relief. (Porting option 2 only) 3. Reversing units shall be used with balanced area cylinders. 9/16-18 Straight Thread SAE #6 O-Ring Ports (5) on a Ø1.66 (42.16) Circle “B” Dimensions Series (in) (mm) 08 5.38 136.6 10 5.50 139.7 12 5.63 143.0 16 5.88 149.3 20 6.13 155.7 24 6.38 162.1 1560-002.P65, pm 5 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit HGF Series Catalog HY13-1560-002/US Columns Standard Column “B” Length .50 Ø1.60 .858 Dia. Gage 1.38 .89 REF .623 Taper Per Foot .156 .875 x 36 Straight Serrations 13/16-20 UNF-2A Thd. Hornwire Column 4.00 “B” Length .89 REF 1.38 .50 .50 Ø1.60 1.00 .156 .858 Dia. Gage (Single or Dual Contact) .623 Taper Per Foot 2.13 .875 x 36 Straight Serrations 13/16-20 UNF-2A Thd. Notes: 1. All dimensions are for reference only. 2. Jacket tube diameter of all columns is 1.50 inches. 3. Column support is required for columns longer than 10 inches. 4. For “B” length see HGF Steering Column Selection Chart, page C16. 1560-002.P65, pm 6 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Catalog HY13-1560-002/US Steering Column Selection Hydrostatic Steering Unit HGF Series HGF Standard Single Hornwire Dual Hornwire Part Number SKF000780400 SKF000780600 SKF000780800 SKF000781200 SKF000781600 SKF000782200 SKF000782400 SKF000783200 SKF000783450 SKF001780800 SKF001781200 SKF001781600 SKF001782400 SKF001783200 SKF002780800 SKF002781200 SKF002781600 SKF002782400 SKF002783200 “B” Length - in (mm) 4 (101.6) 6 (152.4) 8 (203.2) 12 (304.8) 16 (406.4) 22 (558.8) 24 (609.6) 32 (812.8) 34.5 (876.3) 8 (203.2) 12 (304.8) 16 (406.4) 24 (609.6) 32 (812.8) 8 (203.2) 12 (304.8) 16 (406.4) 24 (609.6) 32 (812.8) Specification 7/8" x 36; no horn contact 7/8" x 36; no horn contact 7/8" x 36; no horn contact 7/8" x 36; no horn contact 7/8" x 36; no horn contact 7/8" x 36; no horn contact 7/8" x 36; no horn contact 7/8" x 36; no horn contact 7/8" x 36; no horn contact 7/8" x 36; single horn contact 7/8" x 36; single horn contact 7/8" x 36; single horn contact 7/8" x 36; single horn contact 7/8" x 36; single horn contact 7/8" x 36; dual horn contact 7/8" x 36; dual horn contact 7/8" x 36; dual horn contact 7/8" x 36; dual horn contact 7/8" x 36; dual horn contact HGF Standard Single Hornwire Dual Hornwire Part Number SKF000340400 SKF000340600 SKF000340800 SKF000341200 SKF000341600 SKF000342200 SKF000342400 SKF000343200 SKF000343450 SKF001340800 SKF001341200 SKF001341600 SKF001342400 SKF001343200 SKF002340800 SKF002341200 SKF002341600 SKF002342400 SKF002343200 “B” Length - in (mm) 4 (101.6) 6 (152.4) 8 (203.2) 12 (304.8) 16 (406.4) 22 (558.8) 24 (609.6) 32 (812.8) 34.5 (876.3) 8 (203.2) 12 (304.8) 16 (406.4) 24 (609.6) 32 (812.8) 8 (203.2) 12 (304.8) 16 (406.4) 24 (609.6) 32 (812.8) Specification 3/4" x 40; no horn contact 3/4" x 40; no horn contact 3/4" x 40; no horn contact 3/4" x 40; no horn contact 3/4" x 40; no horn contact 3/4" x 40; no horn contact 3/4" x 40; no horn contact 3/4" x 40; no horn contact 3/4" x 40; no horn contact 3/4" x 40; single horn contact 3/4" x 40; single horn contact 3/4" x 40; single horn contact 3/4" x 40; single horn contact 3/4" x 40; single horn contact 3/4" x 40; dual horn contact 3/4" x 40; dual horn contact 3/4" x 40; dual horn contact 3/4" x 40; dual horn contact 3/4" x 40; dual horn contact Notes: 1. Steering wheel horn button not included in column kits. Order part number 465611 separately. 2. Steering wheel nut included with column. 3. For column lengths or horn wires not shown above, contact your Parker Sales Engineer. 1560-002.P65, pm 7 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit Catalog HY13-1560-002/US Design Advantages Hydraguide™ Each Hydraguide unit consists of a directional control valve and metering section. The valve directs the pressurized oil supplied to and from the cylinder and the Hydraguide metering section. The metering section “meters” out the pressurized oil to the steering cylinder. The Hydraguide works in conjunction with the vehicle’s hydraulic system, which consists of a steering cylinder(s), relief valve, reservoir, filter, fluid lines, and an engine driven pump. The systems must be tailored to the specific vehicle type and service for which it will be used. Parker offers engineering advice and assistance (and encourages use of our engineering assistance) when applying hydrostatic steering to any vehicle. RELIEF VALVE FILTER RESERVOIR CYL. SUPPLY PUMP Typical Steering Circuit 1560-002.P65,pm 8 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Catalog HY13-1560-002/US Hydrostatic Steering Unit System Terminology Open Center, Nonreversing Open Center, Reversing The nonreversing unit keeps the steered wheels in the steered position when the operator releases the steering wheel. The cylinder ports are blocked in the neutral valve position. The operator must steer the wheels back to the straight ahead position. The reversing unit allows the steered wheels to return to the straight ahead position after the operator releases the steering wheel. This happens only if the steering geometry exerts a centering force on the steering cylinder. The cylinder ports are interconnected with the metering section so that the steering wheel follows the wheels back to center position. Reversing steering units should only be used in systems where the opposing cylinder chambers are of equal volume. DO NOT USE with a single unequal area/volume cylinder. STRG. WHL. STRG. WHL. Open Center, Power Beyond (5-line) The Hydraguide has an auxiliary fifth port as a Power Beyond feature to supply fluid to other functions downstream of the Hydraguide (Circuit #1). The Hydraguide automatically takes priority flow for steering, with the remainder available for auxiliary functions. When not steering, all flow is available to auxiliary functions. This system eliminates a flow divider or a separate steering circuit, thus saving energy and component cost. STRG. WHL. 1560-002.P65, pm 9 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Catalog HY13-1560-002/US Hydrostatic Steering Unit System Terminology Closed Center System Closed Center, Nonreversing Closed center systems utilize a variable displacement pump providing variable flow to the steering circuit. All ports of the Hydraguide™ are blocked when the vehicle is not being steered. The amount of flow through the steering circuit depends upon steering speed and displacement of the Hydraguide. STRG. WHL. TO OTHER CIRCUITS NOTE: If the auxiliary circuit requires a large demand from the pump, such that an inadequate amount of pump flow is available for steering, then a flow limiting control valve should be applied to the auxiliary circuit. This is needed to guarantee steering capability under all operating conditions. 1560-002.P65,pm 10 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit Catalog HY13-1560-002/US System Design Process Flow Chart Use the following chart as a guide to design hydrostatic steering systems. 1 2 3 Existing System New system where steering forces and cylinder stroke(s) are known. New system where steering forces and cylinder stroke(s) are unknown. Step I Calculate Kingpin Torque See selection guide for replacement unit. Choose the closest or the next smaller standard displacement. A smaller displacement provides for faster steering speed and more turns lock-to-lock. If necessary, calculate the new valves. Step II Select Steering Unit Step III Calculate Cylinder Force Step IV Determine Cylinder Area Step V Determine Cylinder Stroke Step VI Calculate Swept Volume of Cylinders Step VII Calculate Hydraguide™ Displacement Step VIII Calculate Pump Flow Step IX Measure Maximum Steering Pressure Step X Select a Relief Valve Setting 1560-002.P65, pm 11 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit Catalog HY13-1560-002/US System Design Process STEP I Calculate approximate Kingpin torque (KT) 1.1 Determine coefficient of friction: Select the coefficient of friction (mu) from Chart 1 after calculating E/B. (Kingpin offset/nominal tire width). See Diagram 1. mu Chart 1 (Rubber tires on dry concrete) .7 .6 .5 .4 .3 .2 .1 .2 .4 Diagram 1 .6 1.0 .8 1.2 E B STEP II Select steering unit STEP IV Calculate cylinder area (CA) For small garden tractor-type vehicles, select an HGF — for larger vehicles select HGA or HGB. The purpose of this is to establish what pressure to use in Step IV. CF CA = —— P Where: CF = Cylinder force (pounds) P = Pressure (psi) (This is the pressure rating of the steering unit chosen.) STEP III Calculate approximate cylinder force (CF) KT CF = —— R Where: KT = Kingpin torque (inch-pounds) R = Minimum radius arm (inches) (see Diagram 2) Select the next larger common cylinder bore size available. If one cylinder is used, use the rod end area only and, if two are used, use the rod end area plus the head end area to select the cylinder (Step VI). Diagram 2 f Minimum Radius Arm = R STEP V Determine cylinder stroke Calculate using diagram 2 as a guide and the desired vehicle turning circle. STEP VI Calculate swept volume (SV) of the cylinder(s) 6.1. One balanced cylinder, double acting SV = (Bore area - rod area) x cylinder stroke π SV = — [B2 - R2] x S 4 6.2. One unbalanced cylinder, double acting B E Stroke 1.2 Calculate Kingpin torque: _______ √—B8 a. Head side π x B2 SV = ——— x S 4 2 KT= W (mu) + E2 NOTE: If steered axle wheels are driven (powered), double KT. b. Rod side Same as 6.1 above Where: KT = Kingpin torque in inch-pounds W = Weight on steered axle in pounds (Use maximum overloaded weight anticipated.) mu = Coefficient of friction B = Nominal Tire width (inches) E = Kingpin offset (inches) at the intersection with the ground 1560-002.P65,pm 12 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit Catalog HY13-1560-002/US System Design Process 6.3. Two unbalanced cylinders, double acting πxS SV = ——— (2B2 - R2) 4 Where: SV = Swept volume (volume of oil to move cylinder full stroke) in cubic inches B = Bore diameter (inches) R = Rod diameter (inches) S = Cylinder stroke (inches) STEP VII Calculate Hydraguide™ displacement (HD) SV HD = —— n Where: SV = Swept volume in cubic inches from Step VI n = Number of steering wheel turns lock-tolock (from one end of cylinder stroke to the other). This ranges from 3 to 6 depending on the type of vehicle. Where: Q = Pump flow (gallons/ minutes/ revolutions) HD = Hydraguide displacement (cubic inches) SS = Steering speed (revolutions/ seconds) (Ideal speed of steer = 120 rpms.) When one single rod cylinder is used, calculate n for each direction because it will be different. Select the next closest displacement. If desired, recalculate n as follows: SV n = —————————— Displacement of selected Hydraguide™ Steering Speed The minimum normally considered is 1 rev/sec (60 rpm). An example would be an articulated vehicle. This depends on the safety considerations for avoidance of obstacles under minimum and maximum flow conditions during all speed possibilities of the vehicle. STEP VIII Calculate minimum pump flow (Q) 1.5 rev/sec (90 rpm) is common, and 2 rev/sec (120 rpm) is considered about the maximum input speed achievable by an average person. HD x SS x 60 Q = —————— 231 If the steering wheel speed becomes greater than the pump flow, a dramatic increase in steering wheel effort is felt. STEP IX Measure maximum steering pressure on prototype vehicle Compare this pressure with the pressure rating of the Hydraguide. If it is higher, return to the last part of Step III and recalculate through Step IX again. STEP X Select a relief valve setting The cracking pressure of the relief valve, which is usually defined as the pressure when the relief valve starts to open and discharge flow to the return line, should be greater than the maximum pressure measured on the vehicle. The full flow pressure of the relief valve, which is defined as the pressure when maximum flow is going over the relief valve, must not exceed the pressure rating on the steering unit. NOTE: Reversing units used with balanced area cylinders. HGF Series Open Center Closed Center Power Beyond Operating Parameters: 1800 PSI 8 GPM 3.3 to 9.9 cu. in. Typical Systems: Turf, Material Handling, General Purpose, and Light Agricultural Vehicles. 1560-002.P65, pm 13 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit Catalog HY13-1560-002/US Hydraguide™ System Data Sheet Date _______________ Salesperson ______________________ Phone ___________________ Fax. ___________________ 1. Customer Company _____________________________________________________ Address ______________________________________________________ City _______________________ State ________ Zip Code _________ Country ____________ Customer Contact _________________________ Telephone ____________ Fax ___________ E-Mail Address ___________________________ 2. Vehicle Truck Tractor Lift Truck Earth Mover Articulated Ackerman Tricycle 4-Wheel Other _______________ 3. Vehicle Specifications 3.1 Number of Steered Wheels ___________ Front Wheel Steer Rear Wheel Steer Articulated 3.2 Gross Vehicle Weight and Maximum Weight on Steered Axle: G.V.W. _____________ Lbs. (Kg) G.F.E.W. ____________ Lbs.(Kg) 4. Steering Unit Operating Parameters 4.1 Number of Hand Wheel Turns Requested: _____ 4.1.1 Steering Effort @ Expectations ____ In Lb (Kg. cm.) 4.2 Speed of Steer (Seconds - Lock to Lock): Low Idle ____________ Sec. High Idle ____________ Sec. 4.3 Displacement of Steering Unit: ______________ In.³/Rev. (cc/Rev.) 4.4 Reversing (Load Reactive) (Open Cylinder) 4.5 Power Beyond 4.6 Options Non-Reversing (Non-Load Reactive) (Closed Cylinder) Open Center Closed Center Shock Valves (Crossovers) Load Sense Anticavation Checks ___________________ Relief Valve in Steering Unit Yes No Setting _______ PSI/Kg/cm² 4.7 Hose Line Size ___________ 5. Steering Cylinder 5.1 Number Used ____________ 5.2 Bore ___________ In. (cm) Balanced Yes No 5.2.1 Stroke ____________ In. (cm) 5.2.2 Rod Dia. _____ In (cm) 5.3 Amount of Stroke Used _____________ In. (mm) 5.4 Cylinder Cross Port Relief Valves Yes No Pressure Settings _________ PSI (Kg/cm²) 5.5 Cylinder Line Size (I.D.) _________________ Length ____________________ 5.6 Expected Maximum Pressure __________________ 1560-002.P65,pm 14 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Hydrostatic Steering Unit Catalog HY13-1560-002/US Hydraguide™ System Data Sheet 6. Pump Model Number _______________________ Displacement: 6.1 Flow Control Yes No 6.2 Pressure Relief Integral External 6.3 Flow Divider Yes No 6.4 Pump Flow 6.5 Flow Available Maximum Steering Flow _____ GPM (L/min.) 6.6 Full Engine Speed _________ RPM Fixed Integral Variable External Maximum Relief Setting _______________ PSI (Kg/cm²) High Idle ___________ GPM (L/min.) Low Idle _____________ GPM (L/min) Minimum Steering Flow ____ GPM (L/min) Idle Engine Speed _________ RPM 7. Reservoir 7.1 Capacity _________ Gal. 7.2 Location ____________________________________________________________________________ Integral with Pump Yes No Separate _________________________ (Head Relative to Pump) 7.3 Filtration _________ Micron Normal 7.4 Expected Operating Temperature _______ Absolute 8. Column and Steering Wheel Data 8.1 Steering Wheel Diameter____________ (In/cm) 8.2 Shaft Serration 8.3 Upper Column Extension _____ Length Extended 8.4 Length Required ____________ In/(cm) 3/4 x 40 7/8 x 36 Other ____________________ Yes No Additional Information: 1560-002.P65, pm 15 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Catalog HY13-1560-002/US Hydrostatic Steering Unit 1560-002.P65,pm 16 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA Parker Hannifin Corporation 6035 Parkland Blvd. Cleveland, Ohio 44124-4141 Telephone: (216) 896-3000 Fax: (216) 896-4000 www.parker.com About Parker Hannifin Corporation Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 500 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that control motion in some 1,000 industrial and aerospace markets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic, and electromechanical motion-control solutions. Our Company has the largest distribution network in its field, with over 7,500 distributors serving nearly 400,000 customers worldwide. WARNING Parker Hannifin Corporation Parker’s Charter To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve profitable growth through premier customer service. Product Information North American customers seeking product information, the location of a nearby distributor, or repair services will receive prompt attention by calling the Parker Product Information Center at our toll-free number: 1-800-CPARKER (1-800-272-7537). In Europe, call 00800-C-PARKER-H (00800-2727-5374). The Aerospace Group is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high-technology markets, while achieving growth through premier customer service. The Climate & Industrial Controls Group designs, manufactures and markets system-control and fluid-handling components and systems to refrigeration, air-conditioning and industrial customers worldwide. The Fluid Connectors Group designs, manufactures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems. The Seal Group designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction. The Hydraulics Group designs, produces and markets a full spectrum of hydraulic components and systems to builders and users of industrial and mobile machinery and equipment. The Filtration Group designs, manufactures and markets quality filtration and clarification products, providing customers with the best value, quality, technical support, and global availability. The Automation Group is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide. The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical flow components for worldwide process instrumentation, ultra-high-purity, medical and analytical applications. FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. Offer of Sale The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the "Offer of Sale". Copyright 2003, Parker Hannifin Corporation, All Rights Reserved Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee US HGF Series Hydrostatic Steering Unit Catalog HY13-1560-002/US Parker Hannifin Corporation Catalog HY13-1560-002/US Hydraulic Pump/Motor Division 5000, 02/03, EcoQuest Printing 2745 Snapps Ferry Rd. Greeneville, TN 37745 USA Tel: (423) 639-8151 Fax: (423) 787-2418 Web Site: www.parker.com/pumpmotor