CIRC 00-3649-BW-M3U - Leds-C4

CIRC
00-3649-BW-M3U
IN
Design by GROK Team
TECHNICAL CHARACTERISTICS
The photograph may not match the reference
exactly. Please read the product description to
identify the finish.
Type:
Pendant
IP Protection degrees:
IP20
Location:
DRY
Light source 1:
1 x LED
89W
Warm White - 3000K
9879 lm(N)
CRI 80
Voltage / Frequency:
120V/60Hz
Warranty (Years):
2
Option to extend the guarantee (Years):
5
Units per box:
1
Pes net (lb):
26.57
EAN:
8435381432522
MATERIALS / FINISHES
Download photometric file .ldt /.ies
Structure
material:
Aluminium
Diffuser material: Methacrylate
Structure finish:
Matt white
Diffuser finish:
Tinted
GEAR
Gear included: Yes, electronic
Lm(N): Nominal flow of light in actual working conditions. Its actual flow will depend on the environmental conditions and the efficiency of the optics and/or diffuser.
LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of
the product.
Please consult the sales team to clarify any doubt.
(+34) 973 468 100
[email protected]
www.leds-c4.com
OPTIONAL ACCESORIES
LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the
features of the product.
Please consult the sales team to clarify any doubt.
(+34) 973 468 100
[email protected]
www.leds-c4.com
LEDS, C4 S.A.
CIF/VAT: A-59.410.910
C/ Afueras s/n -TORA- 25750
(LLEIDA) SPAIN
TEL: 34 (73) 46 81 02
FAX: 34 (73) 46 81 06
SHEET: 1/2
EDITION: 01
REF: 00-3647, 00-3648, 00-3649U
FIGURE 7
FIGURE 6
FIGURE N 1. UNPACK THE FIXTURE: CHECK THE
CONTENTS OF THE BOX. YOU SHOULD RECEIVE:
FIGURE N 1. D BALLER LE PLAFONIER: V RIFIER LE
CONTENU DU CARTON, VOUS DEVEZ RECEVOIR:
8
9
x12
FIGURE 3, 4 AND 5 MOUNTING HARDWARE.
NOTE: TEST THE CONNECTOR BY GENTLY PULLING IT. IF IT PULLS OUT THE CONNECTION, TRY
AGAIN TILL YOU HAVE A FIRM CONNECTION. MAKE SURE NO BARE STRANDS OF WIRE STICK OUT
FROM UNDER THE CONNECTORS.
WHITE OR MARKED WIRE
FROM FIXTURE
WHITE WIRE FROM
OUTLET BOX
FIGURE 3
BLACK OR UNMARKED WIRE
BLACK
FIGURE 4
FIGURE 5
x12
FIGURE 3, 4 ET 5 MONTAGE DE L' QUIPE.
IMPORTANT: ESSAYER DE TIRER LE C BLE D'ALIMENTATION DOUCEMENT.S'IL SORT DE LA
CONNECTION, IL FAUDRAIT ASSURER QUE LA CONNECTION SOIT FERME. S'ASSUSER QUE LES FILS
DES C BLES NE SONT PAS D COUVERT DU CONNECTEUR.
C BLE BLANC OU MARQU
DU PLAFONIER
C BLE BLANC DE LA BO TE
FIGURE 3
C BLE NOIRE OU
NOU-MARQU
FIGURE 4
NOIRE
FIGURE 5
"Warning", "This product is to be
installed by a qualified electrician
only."
"Suitable for dry locations only"
"Attention", le raccordement
lectrique sera effectu par un
t chnicien lectricien qualifi "
"Ad quat seulement en lieux secs."
1.- Wrong lighting installation can be dangerous for your safety.
2.- Before starting, disconnect the power by turning off the general switch of the
electric installation.
3.- Install light bulbs (not provided) that must not exceed markings on the fixture.
4.- To change the bulbs, disconnect the power by turning off the general switch and
wait for the bulbs cool down.
1. Une mauvaise installation peut compromettre votre s curit .
2. D connecter la tension du r seau d'alimentation avant de r aliser toute op ration.
3. Installer les ampoules (non fournies), ne pas utiliser d'ampoules d'un autre type ou
d'une puissance sup rieure celle indiqu e sur l' tiquette de la lampe.
4. Pour changer les ampoules, d connecter la tension du r seau d'alimention et
laisser refroider les ampoules.
1.- Make electrical connections, carefully read the Electrical Connection section.
2.- Assemble lighting onto the outlet box as shown on fig. 6, & 7.
(See fig. 3,4 y 5)
1.- Connect the white wire from the fixture to the white wire of the electric installation.
2.- Connect the black wire from the fixture to the black wire of the electric installation.
3.- Connect the grounding conductor from the fixture to the grounding wire of the
electric installation.
4.- Spread out the electrical wires so that the black ones are on one side of the outlet
box and the white ones are on the other side, and carefully introduce them into the
1. Connecter au r seau, lire attentivement la section de "Raccordements lectriques"
2. Installer l'appareil la bo te de distribution comme indiqu dans les dessins 6 et 7.
1. Connecter le c ble blanc de l'appareil au c ble blanc de l'installation lectrique.
2. Connecter le c ble noir de l'appareil au c ble noir de l'installation lectrique.
3. Connecter le c ble conducteur de prise de terre au c ble de prise de terre de
l'installation lectrique.
4. Distribuer les c bles pour que tout le c blage noir soit par dehors et le c blage
blanc soit par dedans. Ajuster et immobiliser la bo te sans coincer aucun c ble.
LEDS, C4 S.A.
CIF/VAT: A-59.410.910
C/ Afueras s/n -TORA- 25750
(LLEIDA) SPAIN
TEL: 34 (73) 46 81 02
FAX: 34 (73) 46 81 06
10A
SHEET: 2/2
EDITION: 01
REF: 00-3647, 00-3648, 00-3649U
10B
10C
x3
x9